Battery Internal Resistance
-
Product
Surface Resistance Meter
WL MIDGET
-
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
Product
Medical Grounding Resistance Tester
2678YM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Medical Grounding Resistance Tester，Product Introduction2678YM Medical Grounding Resistance Tester Is Used To Measure The Internal Electrical Equipment Of Grounding Resistance,Which Reflects The (Contact) Resistance Of Total Grounding Terminal Of Electrical Equipment.It Suitable For Measuring All Kinds Of Motors,Electrical Appliances,Instruments,Household Appliances And Other Equipment Resistan
-
Product
Easy and Non-Destructive Airflow Resistance Measurements of Materials and Parts
CARE+
-
The control of airflow resistance in the production of materials and components is a growing requirement in the automotive industry. CARE+ (Concentric Airflow Resistance Evaluator) is an apparatus designed to measure the airflow resistance of materials and parts. Measuring non-destructively, CARE+ is particularly applicable in the quality control of parts and materials.
-
Product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
miniMasterCharger
-
The miniMasterCharger is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the miniMasterCharger can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.
-
Product
PXI Microwave Relay, Single SPDT, 26.5GHz, 50Ω, SMA, Internal Termination
40-781A-221
Microwave Relay Module
The 40-781A-221 (PXI) and 42-781A-221 (PXIe) are single SPDT 26.5GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Battery Holders And Battery Racks
-
Arbin offers a wide range of options and systems for connecting various types of batteries for testing. From coin cell and cylindrical cell holders and trays to flat/pouch cell holders and racks, we have the full solution for your battery test setup.
-
Product
5V50mA Coin Cell Battery Test Equipment
TOB-5V50mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
Temperature Control Battery Short Circuit Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL'S Temperature control battery short circuit test chamber is designed to comply with standard. According to the short-circuit test requirement, the short-circuit must be less than 5 mΩ to achieve maximum curren.
-
Product
Battery Chargers
-
Following a power outage, various power engineering objects such as power plants should operate on battery back-up systems. It is necessary that these batteries are being properly charged in order to compensate its energy loss and keep their voltage within the predefined limits. DV Power’s chargers are portable and universal battery charging solution. They are primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300 V DC level.Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge. Variety of implemented protections, such as thermal, overcurrent, undervoltage and overvoltage, assure the charging process is safe for the battery and the charger itself.
-
Product
Safety Shoe Electrical Resistance Tester
UI-FT06
-
Safety Shoe Electrical Resistance Tester is to test the electrical resistance of conductive footwear and antistatic footwear.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
-
Product
Surface Resistance Meter
-
Wolfgang Warmbier GmbH & Co. KG
Starterkit for testing conductive an dissipative surfaces and electrostatic fields/surface potentials
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
Product
Battery Charge Discharge Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
-
Product
Winding Resistance Meter
TRM 25
-
SCOPE introduces 25 A state of the art precision winding resistance meter, specially designed for field testing as well as factory testing of large transformers up to 500 MVA. Winding resistance value of transformer and rotating machine are directly displayed on 5.7” TFT display. TRM 25 is designed to work in live EHV switchyard conditions, ensuring operator’s safety and repeatability of results. Maintenance time saving is ensured by one time connection to transformer with simultaneous resistance measurement of three / six windings, measurement of resistances of all taps with automated tap change and demagnetization facility. The meter is protected against the back-EMF offered by large inductive windings.
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
Digital Battery Load Tester
DBT125
-
Battery load test. Depending on the size of the battery, this product adds a very high load to the battery (125 A). It enables the reading of battery condition by voltages and by its ability to maintain the load, thus determining levels of sulphation.
-
Product
Battery Voltage Recorder
BVR Series
-
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and temperature.The BVR Series is the perfect tool for that purpose. All measurements are automatically saved in device’s internal memory. Additionally, DV-B Win software helps the user to download all measured results. Furthermore, the user can create test reports and export them to various formats.BVR series includes two models: BVR11 and BVR22. These are rechargeable handheld devices intended for performing monthly battery inspections and support tools during capacity testing. The list of the applications of these instruments includes:Efficient supplement to BLU series of battery load units during battery discharge testingMonthly inspections of large battery banksAmbient temperature measurementCurrent measurement using current clampsUSB and Bluetooth communication with PCSimultaneous string voltage and current measurement to analyze a discharge test processThe BVR22 model provides Bluetooth communication with an external density meter, for transferring electrolyte specific gravity and temperature readings.
-
Product
Automatic Battery
BATLV1200
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltageinstalations
-
Product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
-
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Software And Hardware Battery Emulation Bundle
E36731ABV
-
The Keysight E36731ABV battery emulation bundle is a complete software and hardware solution for performing battery profiling and emulation, current drain analysis, and battery run-down and cycle testing.
-
Product
CT5 TIME TO GO Battery Charger
40-255
-
The groundbreaking CT5 TIME TO GO (part #40-255) battery charger and maintainer is a world first because it answers the question ‘When will my battery be fully charged?’This means you can plan your day around your battery charging because the CT5 TIME TO GO gives you an accurate prediction of the remaining charging time in hours. Not only that, it’ll also tell you when you can safely try to start your vehicle before the battery is fully charged. The CT5 TIME TO GO uses advanced technology to give you three charging and maintenance programs – Normal, AGM and Recond. It’s easy to use and fully automatic, so it can be connected directly to the battery indefinitely, if required, and it won’t over or under charge. The CT5 also has built-in temperature sensing capabilities.
-
Product
Resistance System Kit
PMK-151
-
The PMK-151 Basic Measurement Kit has all the functionality of the PMK-152, but adds computer downloading capabilities. It contains all the instruments you need to take a variety of resistance measurements.The PMK-151 includes Prostat's PRS-801 Resistance Set with modified 5 pound conductive rubber electrodes, the PRS-801 wide range resistance meter, and Prostat PRS-801 Connectivity software for computer data downloading. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
Product
Battery Test Software
-
Landt Battery Test Systems use different programs for data acquiring and data process. The acquiring software comes with a very user-friendly interface, which allows new users to operate with minimal training. Data process software shows different kinds of plots (Voltage vs. Capacity, Capacity vs. Cycle Number, Efficiency, etc.), which can be easily exported.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
High Voltage Capacitor Batteries
-
Lifasa - International Capacitors, SA
There are a series of elements and materials, just like in the BT equipment, for their operation in AT and that must accompany our AT capacitors for the proper functioning of these and for our installation / network, as well as the rest of equipment that compose it and that are in operation in parallel to the capacitor / s that we want to put into service for the correction of the power factor (compensation of the consumption of reactive energy).
-
Product
Automatic Battery Monitor
BA24-2020
-
The BA24-2020 automatic battery tester makes it easy and efficient to test each cell of a battery. It makes it possible to receive a new battery and to revalidate it regularly.
-
Product
Regenerative Battery Pack Test System
17040E
Test System
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
-
Product
Dual channel battery charger and analyser
TS25 MKII
-
Rugged and reliable designed for busy maintenance workshops, the TS25 MKII charger is suitable for every industry where batteries are used. It features a software controlled self-calibration facility which amounts to zero downtime for calibration.
-
