-
Product
6-48V Nixie Digital Display Circuit Tester
1674B
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12, 24 and 48V systems.
-
Product
Mixed Signal Oscilloscope: 16 GHz, 4 Analog Plus 16 Digital Channels
MSOV164A
Oscilloscope
16 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Programmable Digital Panel Meters
RS485
-
Kusam Electrical Industries Limited
• Manages sending and receiving signal of multiple Modbus RTU instruments.• Programmable address for reading data• Data form: Unsigned Int / Signed Int• Max.Baud rate: 38400• Programmable address:1 ~ 255• With alarm setting and analog output
-
Product
Digital In-Duct Mini Vane Anemometer
DAFM4
-
UEi Test & Measurement Instruments
The DAFM4 is the tool for all your air flow measurement needs. With the DAFM4 you can directly capture air temperature, relative humidity and air velocity. It also calculates wet bulb temperature, dew point temperature and air volume. Enter duct dimensions for live or timed average of air flow in CFM (or CMM), or use the effective area of a grill for outlet volume measurements. Air volume is displayed in real-time, or choose a timed average with start/ stop capabilities to traverse ductwork.
-
Product
Bench Digital Multimeter
8012
-
Model 8012 is a high performance, 20,000-count digital benchtop multimeter. It measures DC and AC voltage, DC and AC current, Resistance, Capacitance, Hz, hFE, Diode, and Continuity. 8012 features a large 4-1/2 digit LCD display with backlight. Maximum voltage measurement is up to 1,000V DC and 750V AC with resolution up to 10 µ V. Maximum current measurement is up to 20A. AC measurement is performed by high accuracy RMS.
-
Product
Digital and Serial I/O
-
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
Product
Software for Making Digital Twins
Replica
-
The next frontier of technological advancement is not new treatment processes or equipment, but instead lies in dynamic process simulation models, advanced visualization techniques, and/or data-driven analysis, leveraged through that can be used for process analysis and project optimization.Digital twins allow solutions to be investigated and tested without putting equipment, public health or the environment at risk. These realistic simulations of facility behavior allow organizations to assess “what if” scenarios in the digital domain and solve for some of the most perplexing challenges, before they can occur — enhancing system understanding and achieving improved system design, optimized operations performance and reduced capital and operating costs.
-
Product
Digital Rotational Viscometer
D443
-
Complete with stand and spindle set - direct display of viscosity in centipoise or millipascal/seconds, percent torque, spindle number and speed (18 speeds 0.3-100RPM). Complete with set of spindles for low or medium viscosity. Complete with hard carrying case. Measures viscosities of dye solutions, pastes, sizing compounds, lubricants or adhesives.
-
Product
High-Speed Digital Cameras
HS Series
-
Fastec Imaging's HS Series high-speed camera is designed with the serious researcher in mind. Image access as well as storage and retrieval have been rethought in order to maximize utility and reduce cycle times.
-
Product
Digital Micron Gauge
DMG150
-
UEi Test & Measurement Instruments
The DMG150 is a Digital Vacuum Micron Gauge with accuracy and precision required by HVAC and refrigeration technicians. Featuring measurements in 5 units including Microns, Pa, mBar, mmHg and mTorr. And is backed by a 1-Year limited warranty.
-
Product
Digital Multimeters
-
Digital multimeter is a must-have tool for professional electrical engineers, electrical technicians and electronics engineers. Multimeters are tools used to detect and troubleshoot electrical and electronic devices. UNI-T’s wide range of multimeter selection guarantees that you can find the most suitable multimeter within your budget that satisfies your needs.
-
Product
Configurable CAN FD Modules With A Focus On Digital I/Os
PCAN MicroMod FD Digital 1&2
-
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The main boards PCAN-MicroMod FD Digital 1 and 2 focus on digital inputs and outputs, which are provided with the appropriate protective circuit. The digital outputs of Digital 1 are equipped with low-side switches and those of Digital 2 with high-side switches.
-
Product
Digital ESU Analyzer
ESU-2050P
-
Calibration quality analyzer; uses external precision non-inductive test loads and wide band current transformer. The Pulsed Model is compatible with all continuous output generators (same as standard model), plus generators with pulsed output waveforms.
-
Product
Digital Torque Meter
TS-3200A
-
The TS-3200A is greatly improved in setting and usability with large sized LCD which offers easy and clear view of good contrast. Setting conditions and measurement data can be displayed in the same screen.
-
Product
Digital Load Calibrator
HS 2000
-
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
Product
Digital Stik Liquid Level Sensor
7250
-
The 7250 Series digital stiks take field proven magnetostrictive sensing technology and packages it for greater reliability and easier installation. This liquid level sensor is ideal for liquid level monitoring, interface level and leak detection in a variety of liquid media in above ground and underground storage tanks. It was designed to meet EPA Leak Detection and API Inventory Monitoring requirements and has been approved for use in hazardous environments.The 7250 Series is series has an inherently lower cost design which results in savings. It provides the same performance and reliability as sensors that consume more power.
-
Product
True RMS Digital Multimeter
MM68
-
The MM68 is a True RMS digital multimeter which measures AC voltage up to 750V, DC voltage up to 1000V and both AC and DC current up to 10A.
It measures frequency, capacitance, resistance, and also has duty cycle, diode test and an audible continuity test which sounds at less than 100Ω. The 4½ digit LCD screen displays the results as values and on a 22 segment analogue bar graph. The MM68 also has an auto-power off feature and on screen low battery indication.
-
Product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
Digital I/O Module
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Ethernet 48-Channel Digital I/O Interface
2410
-
Controls/monitors 48 digital signals over Ethernet PWM output mode Programmable input debounce Input edge detection with asynchronous host notification Compatible with standard solid state relay racks Embedded HTTP and Telnet servers Open source API
-
Product
Professional Automotive Digital Multimeter
CT8027
-
Full autorange features. Large 4 digit LCD display with analog bargraph. AC/DC Voltage measurement up to 600 Volt. AC/DC Current measurement up to 10 A. Tachometer function with inductive pickup measures from 30 to 20000 rpm
-
Product
Multi Range/Multi Gas Digital Mass Flow Controller
SEC-Z500X Series
-
This is HORIBA's best selling model for digital mass flow controllers. It has multi-range/multi-gas functions enabling users to change the type of gas or full-scale flow rate on-site quickly and easily.With high accuracy +/- 1.0% S.P, piezo actuator valve, high speed response and being all-metal this mass flow controller is suitable for process yield improvement and simplified parts management. Digital/Analog, DeviceNet™, and EtherCAT® communications are all available.
-
Product
PXIe-4082, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
783131-01
Digital Multimeter
PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter—The PXIe‑4082 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXIe‑4082 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, frequency, period, and basic L and C measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4082 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
Digital Test Instrumentation
EDigital-Series™
Test Instrument
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
Product
Digital Pressure Gauge
m1M
-
AMETEK Sensors, Test & Calibration
Affordably Accurate! Featuring a 3 year recommended calibration interval, DNV approval, and an easy-to-use, time-saving user interface.
-
Product
Digital Thermometers
-
A large selection of digital thermometers including the Master Class Folding Cooking Thermometer, GM1311, GM1312 general purpose digital themometer, Therma1, Therma Plus waterproof, Therma differential, Therma Hygrometer and Digitron range.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - XMC
Model 71610
-
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- RoHS Compliant Lead-Free Version Available
-
Product
Digital Force Gauge
-
*Compact and light weight*3-way power supply*Display hold function is equipped*Easy zero adjustment function*Automatic recognition of the type of sensor*Judgment function (Hi&Low) is equipped
-
Product
Digital Inclinometer
ZET 7154
-
Digital inclinometer ZET 7154 is used in static systems for platforms positioning control (2-axial mode) with a tolerance below 0,1 %. Low power voltage and CAN protocol enable integration of ZET 7154 digital inclinometer into almost any industrial system. “Set to zero” option allows to calibrate the sensor to zero in every axis, thus preventing platform critical tilt in the set coordinate.
-
Product
Digital Meter Relay
CSS-4/5
-
● Measuring DCA, DCV, ACA, ACV, Hz● Process signal mA, Vdc, Strain Gauge, Potentiometer, Pt100Ω● High accuracy and resolution● User function, easily programmed from the front panel by push-button, and set-point by Dip-Switch● Modular design, and popular input range programmable● Three relay ( Hi / Low / Go ) outputs● Optional excitation supply available
-
Product
Digital Module For Remote I/O
ITA
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
