Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
product
PMC-Parallel-IO
PMC-Parallel-IO provides 64 independent IO in one PMC slot. 64 mA open drain buffers on each IO. Two interrupt sources. External or internal clock reference. Custom state machine designs.
-
product
Digital and Serial I/O
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
product
Analog Multiplexer Board
104-AIM-32
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
product
High-Voltage, High Current I/O Module
Model JI-4516
The JI-4516 module is a versatile, easy-to-use device for adding high-voltage, high-current digital I/O capability to a computer system via a USB connection. The module is comprised of 8, low-side power MOSFET switches, and 8 high-voltage inputs. I/O ground isolation eliminates ground-loops and provides protection from noise and switching transients during high-current load switching. The JI-4516 is available as either a desktop unit or low-cost OEM board.
-
product
Voltage Input Module For Remote I/O
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
product
Avionics I/O Computers
With so many built-in capabilities, these highly-flexible avionics I/O computers are the ideal fit for a wide range of applications.
-
product
Isolated Digital I/O Card
PCIe-IDIO-24
This product is a x1 lane PCIe isolated digital input and FET output board with Change of State (COS) detection capabilities. In addition to the isolated signals, 8 (or 4) TTL/CMOS input/output pins are available, for your application’s convenience.
-
product
Analog Output Module, 16-bit D/A
IP230A
Jumper-selectable output ranges give you the choice of unipolar or bipolar voltage output. And for greater flexibility, the IP230A module accepts conversion start triggers from software commands, or from external sources for synchronization to specific events.
-
product
Analog Oscilloscope
PS-1000
* 100MHz BANDWIDTH. * 20MHz LIMIT. *1mV SENSITIVITY. *2.0nS RESOLUTION. *CE. TUV GS, UL, CUL, IEC1010
-
product
I2C Interface for Digital I/O Control
EE301-I2C
Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable
-
product
Analog Output DAQ Cards
Analog output cards are ideal for DAQ applications where multiple A/O channels are needed for voltage and current output.
-
product
Analog Output Cards
PCIe-DA16-6
The PCIe-DA16-6 series are x1 10.5” cards that can be installed in long PCIe slots. They contain six, four, or two digital-to-analog converters (DACs) and 16 bits of digital I/O.
-
product
Analog Discovery Pro Line
Despite Digilent's origin in education, there is a growing demand for products that provide flexibility along with more robust capabilities that professional applications need. Digilent's Analog Discovery Pro line gives engineers the ability to tap into the efficiency of the WaveForms software while offering a wider selection of specifications in products created with the professional in mind.
-
product
I/O Wiring Cable
PCL Series
I/O wiring cable sets are designed for easy field wiring capabilities. The PCL-1050 I/O wiring cable series can be used with multiple I/O cards.
-
product
4-CH Analog Output Module
HSL-AO4-U
The HSL-AO4 offers four analog output channels with a high drive capacity based on the HSL bus. The HSL-AO4 also features 16-bit resolution and offset/gain calibration to minimize the power-on 0-voltage drift to meet precise analog output requirements.
-
product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
I/O Board
For more expansion and convenience, we offer a ready to use I/O boards which are specially designed for Pico-ITX SBCs.
-
product
Digital I/O Card
PCI-DIO-120
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
Analog Limiter
SIM964
Stanford Research Systems, Inc.
The SIM964 Analog Limiter provides upper and lower voltage limits for conditioning dynamic signals. Limits are set between ±10 V with 10 mV resolution. Two rear-panel TTL signals are activated when upper or lower limits are exceeded.
-
product
Isolated/Relay Digital I/O Terminal
Isolated digital I/O terminals boards and I/O wiring boards offer isolated input channels. The I/O terminals also feature high-voltage protection.
-
product
PLD For Bridging, Infinitely Reconfigurable I/O Expansion.
MachXO
*Up to 27.6 Kbits sysMEM™ embedded block RAM and up to 7.7Kbits distributed RAM*SRAM based logic can be reconfigured in milliseconds using JTAG port*IOs support LVCMOS, LVTTL, PCI, LVDS, Bus-LVDS, LVPECL, RSDS*Up to two analog PLLs per device that enable clock multiplication, division, and phase shifting*Available in TQFP, csBGA, caBGA and ftBGA packages
-
product
Analog Test Instruments
Analog test building blocks for high performance ATE. VXI-based Core System Instruments (CSi) ZT-Series™ PXI/LXI instruments.
-
product
SignalScope Pro for iOS
SignalScope Pro
SignalScope Pro for iOS devices is a real-time analysis toolset, suitable for use in areas such as acoustics, audio, electronics, and vibration. SignalScope Pro includes 4 tools for dynamic signal analysis, as well as a signal generator for producing test signals. See YouTube for video demos.SignalScope Pro also turns your iOS device into a platform for data acquisition, storing acquired data in CSV or TXT files, MAT-files, or PDF or JPEG images for later retrieval from your device.
-
product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Thermalert Clinical Montoring Thermometer With Analog Output
TH-5/AOP
The TH-5?AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-5/AOP offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-5 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
product
Virtex-4 FPGA with Plug-in I/O
PMC-LX
Acromag’s PMC-LX boards use a high-performance Xilinx® Virtex-4TM FPGA, but maintain a relatively low price point. They are optimized for high-performance logic, featuring a high logic-to-feature ratio and a high I/O-to-feature ratio. Two modules let you select a FPGA to match your logic requirements.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
FMC-LPC I/O Module
FM191
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
product
PoE-PSE I/O Board
AX93280
*PoE-PSE I/O board complies with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device





























