Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
PCI Express Analog and Digital I/O
826
-
Six advanced 32-bit counters Directly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement 16 analog inputs, 16-bit, 300 ks/s 8 analog outputs, 16-bit, 900 ks/s 48 digital I/Os with edge capture Watchdog timer, 3 stages
-
Product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
Digital I/O Module
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Analog Backplanes
MSXB 031
-
Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical.
-
Product
PCI Digital I/O
APC464
-
Four 16-bit multifunction counters/timers are configurable for pulse width modulated output, watchdog timer, event counter, frequency measurement, pulse width measurement, period measurement, or one shot pulse output. The four 16-bit counters can also be configured into two 32-bit counter/timers.
-
Product
PCI D/S, S/D, I/O & Comm Board
76CS3
Multifunction I/O
NAI’s 76CS3 is a PCI/PCIe multifunction I/O and communication board designed for applications requiring Digital-to-Synchro/Resolver (D/S) and Digital-to-LVDT/RVDT (DLV) stimulus output, as well as I/O and communication functions. This full-slot board contains five independent, function module slots. The board can be configured for 6 separate D/S channels, or for D/S in combination with I/O and communication modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Modbus RTU Analog Input
-
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
Product
Light-to-Analog Sensors (Current)
-
Renesas' light-to-current silicon optical sensors combine a photodiode array and current amplifiers on a single monolithic IC. These devices are ideal for display and keypad dimming, as well as industrial and medical light sensing applications.
-
Product
16-Ch Source-Type Digital Output EtherCAT Slice IO Module
AMAX-5057SO
Digital I/O Module
Channels:16 (Source Type)Voltage Rating:10~30VDCRated Current Output:0.5A per channel atsignal "1"Leakage Current:10 μA per channel atsignal "0"Output Delay:From logic level 0 to 1:150μs; From logic level 1 to 0: 2ms
-
Product
16-bit, 200KHz, 16 Isolated Differential Analog Input Board, 8 Isolated 24V Digital I/O
APCI-3002
-
Analog input board, 16-bit resolution, 16 differential inputs with 200 kHz sampling rate.
-
Product
8-Ch Analog Input Module
ADAM-5017
Analog Input Module
Accuracy: ±0.1% or betterEffective resolution: 16-bitInput range: ±150 mV, ±500 mV, ±1 V, ±5 V, ±10 V; ±20 mASampling rate: 10 samples/sec. (total)Isolation voltage: 3000 VDCFault and overvoltage protection: withstands overvoltage up to ±35 Vlnput type: mV, V, mAChannels: 8 differential
-
Product
Analog Only Oscilloscopes
-
Isolated Signal Generator (0-65MHz, Sine Wave Only) for serial numbers above 4000. The CS701 is rated at 300V RMS isolation (class III), and offers output levels from 1 mVp-p to 7 V p-p. You can use the CS701 for Power Supply FRA without needing an isolation injection transformer.
-
-
Product
miniPCIe IO and Processing Module
Solar Express 50 (SE50)
-
Sundance Multiprocessor Technology Ltd.
The SE50 Mini PCIe card is a small form factor board used to implement the PCI Express interface to expand embedded PC I/O. The card size is 30mm wide by 50.95mm long.
-
Product
IoT Ethernet I/O Modules
WISE-4000/LAN
-
The WISE-4000/LAN series is a newly designed IoT Ethernet I/O module which supports new RESTful web API for IoT applications. A HTML5 web configure interface enables users to configure WISE modules without the limitation of a platform or operation system. The built-in data logger function logs data with time information, then be retrieved in a bundle. Wide operating temperatures enable the WISE series to be implemented in more IoT data acquisition applications.
-
Product
Analog In-Circuit Tester
406C
-
The 406C is an open architecture power up test platform designed to facilitate the implementation of functional testing after the MDA test is completed. Internally dubbed as "Armadillo" the new architecture provides the user almost unlimited flexibility by combining the best of the VME buss and a dedicated ICT buss.
-
Product
Multi I/O FMC Module
FMC155
-
The FMC155 is an FPGA Mezzanine Card (FMC) per VITA 57.1 standard, offering a small footprint and allowing for general-purpose I/O expansion. The FMC155 provides sixteen LVDS input/outputs, eight RS-485/422 RX plus eight RS-485/422 TX, and sixteen single-ended +3.3 V input/outputs.
-
Product
Analog Filter
SIM965
-
Stanford Research Systems, Inc.
The SIM965 Analog Filter is ideal for signal conditioning applications where Bessel or Butterworth filters are needed. Bessel filters offer clean step response (negligible overshoot) and linear phase response, while Butterworth filters provide excellent pass-band flatness with some overshoot
-
Product
PXI RF Analog Signal Generator
Signal Generator
PXI RF Analog Signal Generators deliver the functionality of RF signal generators to the modular, compact PXI form factor. These modules support frequency ranges from 250 kHz to 20 GHz. You can combine PXI RF Analog Signal Generators with other PXI modular instrumentation to design automated test systems for radar, RF integrated circuits (RFICs), and automotive test applications.
-
Product
Ethernet I/O Modules
ADAM-6000
-
Advantech's Ethernet I/O Modules, ADAM-6000 series, accomplishes this integration easily through the latest internet technology, so that it can remotely monitor the device status more flexibly. ADAM-6000 modules are empowered by Peer-to-Peer (P2P) and Graphic Condition Logic (GCL), and can perform as standalone products for measurement, control and automation with Advantech's P2P and GCL technology.
-
Product
8-Ch, 16-Bit, 200 KS/s Isolated Analog Input USB 3.0 I/O Module
USB-5817
Data Acquisition Module
USB 3.0 SuperSpeedDaisy chainable by built-in USB hub8 x 16-bit analog input channels with 2,500 VDC isolationSupport voltage and current measurementWide common-mode voltage range (±275 V)Removable European-type connectorSupported operating systems: Windows 10/11
-
Product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
Analog Output Module
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
Digital I/O Card
PCIe-DIO-120
-
This product is a x1 lane PCIe DIO board available in economy to high-performance models ranging from basic 72-, 96, and 120 DIO lines to advanced COS detection. The card emulates 8255 compatible chips using FPGA technology, providing up to 120 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs.
-
Product
Analog Isolation Board
MSXB 027
-
The MSXB 027 Analog Isolation Board accommodates up to 8 isolation modules in any combination of input and output. Up to 64 5B Analog Isolation Boards can be connected to a single DAP for a total of 512 isolated channels. When used in conjunction with Analog Output Expansion Boards, up to 66 of these channels can be specified as isolated analog outputs.
-
Product
SignalScope Pro for iOS
SignalScope Pro
-
SignalScope Pro for iOS devices is a real-time analysis toolset, suitable for use in areas such as acoustics, audio, electronics, and vibration. SignalScope Pro includes 4 tools for dynamic signal analysis, as well as a signal generator for producing test signals. See YouTube for video demos.SignalScope Pro also turns your iOS device into a platform for data acquisition, storing acquired data in CSV or TXT files, MAT-files, or PDF or JPEG images for later retrieval from your device.
-
Product
Remote I/O Systems
-
The clear assignment of a signal to a terminal while maintaining the existing instrumentation and wiring is a major advantage of remote I/O . A second is the significantly reduced wiring through the use of a bus interface to the control system - remote I/O offers the best of two technologies and is therefore ideally suited for modernizing and expanding process plants.
-
Product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
Digital I/O Module
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
Industrial Automation & I/O
-
Advantech offers versatile I/O and automation devices from sensor modules, add-on DAQ cards or portable modules, remote I/O and wireless I/O devices, to IoT I/O gateways, RTUs, embedded automation computers, HMIs and software tools, which not only satisfy data acquisition, measurement, control, and communication needs but also allows cloud integration for wider area data management systems.
-
Product
I/O Signal Marshalling
-
We offer you a variety of solutions for I/O signal marshalling in process automation:The flexible VIP I/O marshalling signal marshalling system makes I/O signal marshalling for universal I/O consistent, from the field to the controller. Our Termination Carriers provide you with a Plug and Play solution for standard I/O system signal marshalling enabling you to connect classic DIN rail devices to the standard I/O cards of your automation system.
-
Product
Analog Input DAQ Cards
-
Advantech analog input card provide AI channels that provide continuous, non-stop, high-speed, streaming A/D data conversion samples to host memory.
-
Product
Digital Module For Remote I/O
ITA
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
