High Voltage Testers
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
Line Leakage Tester
LineCHECK II
-
Designed for Automated Test ApplicationsFull Compliment of Automation InterfacesComplete Line Leakage Testing SolutionEnhanced Graphic LCDCompatible with Scanning Matrix for Patient Lead TestingContinuous Run FeatureSoftware CompatibleSafety Agency Listed
-
Product
Power Supply Voltage Fluctuation Simulator
SG Series
-
Simulator to reproduce DC supply voltage variations phenomena in the vehicle environment for evaluating immunity of automotive electronics. This simulator can perform various tests against voltage variations required by ISO 16750 and other international standards. Please contact us for voltage variations testers to perform testing to manufacturers' private standards.
-
Product
Endurance Tester
-
Premier's Endurance Tester, also known as on-off tester and life tester, is used to perform the life test of the unit. The Endurance Tester, switches on the unit for a set time and then turns it off for a set time. This entire cycle is repeated multiple times, to simulate the behavior of the unit under extended use
-
Product
SOLAR CELL TESTER
-
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-355-HI
-
The 40-230-355-HI (PXI) and 42-230-355-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Voltage Detectors
-
Available with a digital readout or a simplified LED display Seaward's specialist range of voltage detectors have the versatility and durability to cope with all types of user demands.
-
-
Product
Waterproof Ozone Tester
ORPTestr 10
-
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
Ink Rub Tester
RT-01
-
Ink Rub tester, also known as abrasion resistance tester, using ASTM D5264 and is designed to measure the ink resistance against rubbing on packaging materials. RT-01 Ink Rub Tester is designed for the abrasion resistance of surface coating layers of printed materials, such as ink layer or photosensitive coating.
-
Product
4 (High Voltage) D/A Outputs (+20 VDC to +80 VDC)
DA4
-
The DA4 module features 4 high-voltage D/A output channels with a maximum full-scale range of ±80 VDC at ±10 mA (max).
-
Product
High Impedance Active Probes
18C & 19C
-
High impedance probes, PICOPROBE® MODEL 18C and MODEL 19C, combine the most advanced MOS and bipolar technologies with special, low capacitance packaging techniques to achieve truly remarkable electronic measurement capabilities. While being manufactured each instrument is individually optimized for the best possible performance. The extremely low input capacitance, high input impedance, and almost negligible input leakage current permits the direct probing of even the most sensitive MOS dynamic nodes. At the same time, the full dc capability of this Picoprobe coupled with the high speed capability permits the full characterization of circuits.
-
Product
Insulation Resistance Tester
UDH-50-1-T
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated•Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV •Resistance range to 1TΩ •Continuous digital display on LCM•Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
Product
CCTV Monitor Testers
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA CCTV Moniter Tester has a built-in high-resolution and wide-size high-definition screen display, automatic video signal detection (AHD / TVI / CVI). The design of the monitor and wristband is ergonomic and convenient to use at any time and place.
-
Product
Insulation Testers
-
Rishabh Instruments Pvt. Ltd.,
Rishabh Insulation Tester is a Digital Insulation Tester with selectable test voltage up to 10kV and Insulation. Resistance measurement upto 20 TΩ. Ideal for testing insulation in live switchyards.
-
Product
CT Admittance Tester
505B
-
Red Phase Instruments Australia Pty Ltd.
Field testing kWh meters is easy, field testing CTs when live is much more difficult. Our admittance tester can test CTs live with 50Hz or 60Hz current in the metering circuit. This technique does not confirm the accuracy of a CT but it will detect faults that give metering errors, such as shorted turns, metering circuits shorted to ground and tampering of CTs. CT faults can cause large revenue losses. Admittance testing only adds 10 minutes to a routine polyphase meter test, giving cheap insurance.
-
Product
DC Hipot Testers
DPC series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
DPC series hipots are used for proof testing of high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for electrical equipments. Other areas include: Cable breakdown testing, capacitor charging and general laboratory use.
-
Product
Medium Voltage Drives
-
Target markets include Oil and Gas, Water and Wastewater, Power Generation, Rubber and Tire, Mining, Cement and other industrial applications. They can be applied equally well to applications requiring Constant Torque (CT) output performance as well as the traditional Variable Torque (VT) pump and fan loads.
-
Product
Demattia Flex Tester
UI-FT33
-
Demattia Flex Tester & Demattia Flex-Cracking Tester is used to test rubber crack growth under repeated bending or flexing. Unuo manufactures demattia flexing fatigue tester which meets test methods of ASTM-D813, GB/T 13934, HG 2873, ISO 132:1999(E), BS 903-A10 and etc.
-
Product
Tester For Maintenance
-
Mobile wiring testers in Multibox design or in customer specific housing for maintenance on military vehicles.
-
Product
Optical Probes- High Bandwidth
DPO7OE
-
The DPO7OE series optical probes with a DPO70000 real-time scope deliver the performance and advanced debug capabilities designers need to fully troubleshoot 400G PAM4 signals, up to 56 GBaud, and reduce time to market.
-
Product
CMOS Drive High Voltage SIL Reed Relays for up to 3 kilovolts
Series 101
-
Direct drive from 74HC/HCT Cmos SIL Relay. Dry or Mercury Wetted switches. 5 Volt coil for 1A dry version is 1600 0r 3000 Ohms
-
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-133-HI
-
The 40-230-133-HI (PXI) and 42-230-133-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Vapor Pressure Tester
-
The MINIVAP laboratory and process vapor pressure analyzers are the worldwide accepted standard instruments for the determination of the vapor pressure of gasoline, crude oil and LPG.
-
Product
High Performance Cameras
-
High performance cameras for imaging and image analysis. A variety of products offer unique performance in spectral sensitivity, spatial resolution and readout speed for needs in various applications. Variety of software products from standard software comes with camera products to specialized software such as controlling peripheral devices, image processing and image analysis.
-
Product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
42-321-103-HI
-
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
Magnetic Field Tester
MS-440
-
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
