Shock wave
short moment intense amplitude faster than sound wave
See Also: Wave, Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave
-
Product
Hydraulic Vertical Shock Test System
KRD10 series
-
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
-
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
Product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
-
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
Product
Pressure Sensors For Blast Testing
-
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
Product
Acoustic Scoring System
AcoustiScore
-
Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Product
Pneumatic Horizontal Shock Test System
KRD12 series
-
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Thermal Shock Testing
-
Thermal shock is a very important test for determining the reliability of a product when subjected to sudden changes in temperature and how this stress source can accumulate deterioration or physical damage in performance.
-
Product
Wave and Tide Sensor
-
Aanderaa Wave and Tide Sensors are compact fully integrated sensor for measuring the wave and tide conditions designed to be mounted on the Aanderaa multiparameter SeaGuard Platform or via cable connected to SmartGuard datalogger.
-
Product
Shock Tester
DP-1200
-
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
Thermal Shock
-
Trialon routinely test products for the automotive, military, medical, aerospace, heavy truck and customer markets in our facilities in Michigan and Indiana.
-
Product
Mechanical Shock
-
Trialon has Mechanical Shock systems that provide sudden acceleration and deceleration to your components and systems along with the supporting capabilities to measure and analyze the response.
-
Product
Pendulum Shock Testing Machine
UDAR-1
-
Pendulum shock testing machine “UDAR-1” is intended for calibration and verification of measuring transducers (both analog and digital) by means of shock impact as well as for shock testing of various specimen.
-
Product
Shock Test
-
Shock testing determines the ability of equipment to withstand the infrequent non-repetitive shocks encountered in handling, transportation, and service and to continue to function, where required. Also, shock tests verify that equipment will not detach from its mounting during these tests.
-
Product
Millimeter Wave Control Devices
-
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
Product
Shock Reactance
ICR260 330
-
Lifasa - International Capacitors, SA
Shock reactors are necessary to limit the transient currents that occur in the connection of the capacitors.
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
Product
Industrial Shock Absorbers
-
ACE industrial shock absorbers work hard. Their application means moving loads are evenly decelerated over the full stroke. The result: the lowest braking force and shortest braking time. The MAGNUM series from ACE is viewed as the reference standard for medium-sized damping technology.
-
Product
Shock Test Systems
-
Accurately measure the fragility of products and evaluate how they respond to specific shock inputs.
-
Product
Thermal Shock Chamber
-
Allows for the rapid transfer of products between temperature extremes, or the alternating heating and cooling of test articles in cyclical manner.
-
Product
Traveling Wave Fault Locator
XC-2100E
-
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Viscoelastic Shock Absorbers
-
This series is the interesting addition to ACE's security portfolio. Simple and compact in design, durable and maintenance-free in operation, these dampers are effective alternatives to existing emergency stop solutions.
-
Product
Thermal Shock Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Thermal Shock Chambers are designed for the safe, efficient, and accurate environmental testing of electronics and consumer products, and aerospace, telecommunications, and military and defense components.
-
Product
Millimeter Wave Orthomode Transducers
-
We are developing a series of millimeter wave orthomode transducers. These orthomode transducers are fullband, compact components. They achieve astounding cross-polarization while maintaining Micro Harmonics’ impressively low insertion loss.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
Microwave/Millimeter Wave Devices
-
We at AET Associates, Inc. take pride in our engineers who have in-depth technical knowledge in the areas of microwave and millimeter wave technology. We hope that we can serve you to benefit your research and development, production, and purchase strategies.
-
Product
Thermal Shock Test Chamber
-
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
