MIxed Signal Test Systems
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, Mixed Signal Testers
-
Product
Swept Test System For Optical Components
-
measurement platform for optical components with a fastscan speed, high resolution and accuracy. The systemcombinesour tunable lasers, polarization controller, power meter and software.
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
High Performance EV Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
The 6V series battery test system uses a full-bridge circuit topology with a higher digit sampling chip. It can provide higher precision and more dynamic test data, and can provide a complete test program for mainstream lithium-ion batteries and batteries with a variety of material systems such as sodium batteries.
-
Product
Signal Amplifier
A10160
Amplifier
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
Product
Mobile Measuring & Testing Systems
-
Individual testing tasks for technical plants and large machines often require the use of a large number of measuring instruments on site, which are difficult to network with each other and which, in the case of complex measurements, require a lot of experience and time in operating the measuring equipment and analysing the recorded measured values. The applications and possible uses can be quite different:
-
Product
Mixed Signal Oscilloscope: 33 GHz, 4 Analog Plus 16 Digital Channels
MSOV334A
Oscilloscope
33 GHz analog bandwidth4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
High Voltage Cable/Harness Test System
CKT1175-50
-
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
Product
Digital Interconnect Test System, Reference Solution
Test System
When you need to measure advanced S-parameters with a fast, low-cost and easy-to-use test solution, the Digital Interconnect Test System gives you a significant edge. It provides a full 32-port vector network analyzer (VNA) configured within a single PXI chassis – ideal for high-speed cable testing. And lets you test any linear passive interconnect faster and easier, including backplanes, connectors and PCBs. Sharpen your edge with Keysight’s Digital Interconnect Test System that enables signal integrity characterization of multiport interconnect products.
-
Product
Signal Analysis
STA/LTA Detector
-
The STA/LTA Detector program is a representation of a detector of various events in triaxial or single-component time signals. The software is based on one of the STA/LTA detector types.
-
Product
Test Management Software
ActivATE™
test
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Electroluminescence Test Systems
-
The products of the SolarModule EL-inline family are integrated into a module production line, before lamination, after lamination or at the end directly after the performance measurement. High-resolution cameras provide excellent image quality and allow the automatic detection of relevant defects. A manual evaluation of images is no longer necessary, which means that considerable costs can be saved. Communication to upstream and downstream processes is flexible and can be adapted to all common interfaces.
-
Product
Signal Analyzers
-
Anritsu's Mobile Wireless Signal Analyzers are the very latest high-performance signal analyzers for next-generation communication applications.
-
Product
Accelerated Life Test Systems
-
Test systems for accelerated life testing and product burn-in utilize Intepro’s electronic loads that are ideal where high power bulk loading is required. Characterization applications within Telecommunication and Aerospace sectors benefit from Intepro’s environmental stress screening (ESS)/Burn-in solutions
-
Product
Wireless Test System
WTS-80
-
CETECOM offers a wide range of services and solutions to help companies develop and execute product testing plans to determine a product’s compliance status and master the increasingly complex regulatory issues of the international market.
-
Product
Memory Test System
T5801
Test System
Capable of Testing Ultra-High-Speed DRAM Devices, Supporting Next-Generation GDDR7, LPDDR6, and DDR6 Technologies
-
Product
Vibrator Test System
Sandwich Box Kit
-
"Gold standard” for vibrator tests provides more information than radio, wireline similarities or internal analysis. Other forms of vibrator QC use the vibrator controller accelerometers to measure vibrator motion. The Sandwich Box system includes external accelerometers which are used to independently record vibrator motion, thus providing a check of the whole vibrator system including the accelerometers.
-
Product
Automated Test Systems
-
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
200 Vdc External Voltage Bias Fixture
16065A
Test Fixture
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
Mixed Signal Oscilloscope, 100 MHz, 2 Analog Plus 16 Digital Channels
MSOX3012A
Oscilloscope
100 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Mixed Signal Oscilloscope
iMSO-104
-
the first mixed signal oscilloscope designed specifically for the iPhone, iPod touch, & iPad. It's intuitive and easy to use, which is why it's the preferred scope for the next generation of inventors. But don't take our word for it. Download iMSO in the App Store and test drive the interface for free.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
-
Product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
Brake Test Systems
GIANT 9000 Series
-
The major test target is to detect noise and vibrations generated by the vehicles brake. Our intention was to build a dynamometer that can operate either with brakes mounted to the complete vehicle, or with just the axle module mounted to a universal adaptor system or wheel suspensions.
-
Product
Brake Test Systems
-
Worldwide, high-speed transport is getting more important. Only through continued improvement and expansion of braking systems, will suppliers all around the world provide a solid foundation for safe traffic. HORIBA has been successfully making brake test stands for more than 90 years.
-
Product
Dynamic Component Test Systems
-
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
Product
Analog Mixed Signal Testers
-
- PC-performance independent: multiple SPEA CPUs provide test program timing, while pc replacement does not require the test program requalification- Pattern-based programming: -30% test time vs competitors- 64-line synchrobus and 16-line high-speed synchrobus for real-time instrument synchronization: no embedded delay when running pattern-based testing- 99% parallel test efficiency- Multi-site test capabilities for up to 256 devices in parallel- High-density, floating instruments, for true parallel analog test- Universal slot architecture, up to 1,408 channels- RF generators up to 3 GHz
-
Product
Signal Conditioner
SA420
-
Features • Works with a remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • Accepts wide range of input frequencies 0.01 Hz to 10 kHz • 4-20 mA and 0-10 VDC outputs proportional to shaft speed • Field adjustable calibration • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • DIN rail mount
-
Product
Handset Noise Under RF Test System
BK8021
-
If you need to evaluate the resistance of cellphones to RF interferance, the BaKo Type BK8021 Handset Noise Under RF Test System is what you need. It performs four tests to evaluate the Sending Noise, Sending Sensitivity, Sending Loudness, Sidetone Masking, Receiving Sensitivity and Receiving Loudness. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When testing is complete, you can print the data as an MS Excel report or save it for comparison and analysis.
