Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Transconductance Amplifier
1620A
-
The 1620A provides high accuracy current levels from dc to over 10 kHz for calibrating ammeters, current transformers and shunts. It also provides output current up to 100 Amperes and as such may also be used as a high accuracy power supply, and as a power source in welding and bonding applications.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
High Voltage, High Current Linear Amplifier
P100
-
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Cable Type]
PM-45
-
Panasonic Industrial Devices Sales Company of America
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Cable Type]
-
Product
Pulse Data Logger
Pulse101A
-
The Pulse101A is one of MadgeTech's best selling data loggers. It is part of an original series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Product
Panel-mounted Amplifier(Power System Simulation )
PA30Bi-H
-
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
-
Product
High Speed High Voltage Amplifier
WMA-300A/360
-
The WMA-300A/360 model is a -180V to +180V (360Vpp) high speed, high voltage amplifier designed for driving capacitive loads, such as piezo actuators, capacitive MEMS and EO-modulators.
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Pulse Oximeter Simulators
-
Take control of all your simulations with the next-generation SpO2 pulse oximeter simulator, OxSim Flex. The world’s smallest SpO2 tester now provides complete flexibility in selecting saturation, pulse rate and perfusion index. Users can create customized Preset Simulations for faster testing of oximeter performance and for alarm testing without having to change the monitor’s alarm settings!
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
Signal Amplifier
9100A
Amplifier
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
High Throughput 1 ns Pulsed IV Memory Test Solution
NX5730A
Test Platform
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
Product
RF Amplifier
SA1012
-
Hangzhou Softel Optic Co., Ltd.
*Forward path use import low noise push pull amplify module or GaAs push pull module,2 Power-Double module or GaAs amplify module are used as output stage, Output level is stable and nonlinear index is good, import high index amplify module are used on return path, It's distortion is little and SNR is high.*It is more convenient to debug because of plug-in(or adjustable) duplex filters, plug -in fixed(or adjustable)equalizers, plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Separate Amplifier Pressure Sensor
AP-40 Series
-
Separate Amplifier Pressure Sensor. The industry's smallest and lightest air pressure sensor head, weighing only 7g. The super-small sensor head can be mounted close to the detection point decreasing response time.
-
Product
For Detecting Low Range And Leakage AC/DC/Pulsed Current.
FDAZCT-20L-0.6S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Lowest Influence from Magnetization,Temperature *Change,Residual Current and Terrestrial Magnetism.*Low Cost and High Performance (Output Linearity ±1% F.S)
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Solid State Power Amplifiers (SSPAs)
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
* Ruggedized for use in pulsed airborne, naval and ground radar* Found in weather forecasting Doppler radar systems* Utilized world-wide in air traffic control and precision approach radar systems
-
Product
Test & Measurement Instrument Amplifiers
MPA-series
-
The MPA-series Test & Measurement Instrument Amplifiers are based on state-of-the-art GaN PA modules and operate from 0.7 to 26.5 GHz (multiple frequency options are available). They provide High continuous power across the band, high linearity for wideband communications testing, have variable gain adjustment and a high-resolution display shows amplifier status. Amplifiers offer a wide range of application-specific requirements including simultaneous high-power, wide bandwidth, low harmonic power and high linearity.
-
Product
Miniature Measuring Amplifiers
MAL Series
-
5B connection technology is based on the common 5B industrial standard and is intended to be a supplement to the 5B measuring amplifiers
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Pulse Laser
-
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
