Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Real-Time Pulse Detection Firmware
FWPD
-
The core challenge in pulse detection is to design a system for random events. The Teledyne SP Devices’s firmware option FWPD, for the ADQ14 and ADQ7, is tailored to detected and analyze pulses in demanding measurement applications where the properties of the pulses (such as timing or length) are not known in advance.
-
Product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX02
Frequency Extender
The N5293AX02 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 110 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
Terminal Board
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
Electro Optical Terahertz Pulse Reflectometry
EOTPR 3000
-
The EOTPR 3000 system is configured with a manual probe station to meet today’s tough FA environment which requires to isolate fault location in minutes rather than hours or days, while maintaining the EOTPR’s world leading sub-5 μm fault isolation accuracy.
-
Product
100mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
RF Medium / High Power Amplifier
-
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Amplifiers
-
Transcat is your premier provider of frequency/waveform generator Amplifiers. We carry an extensive inventory of test & measurement equipment, with over 3000 products available for same-day shipping. For many instruments, new instrument calibration is also available, ensuring that your product is tested and ready for use as soon as you get it.
-
Product
High-Power Pulsed Magnetron-based generators
Pulsed DNP
-
Insight Product Company offers High-Power Pulsed Magnetron-based generators for pulsed Dynamic Nuclear Polarization (DNP) experiments.
-
Product
Measurement Amplifier In Rugged IP65 Housing
-
INELTA Sensorsysteme GmbH & Co. KG
For DMS Force Sensors and LVDT
-
Product
Pulse And Universal Generator With 25 Or 50MHz Models, Single Or Dual Channel
TGP3100 Series
-
The TGP3100 Series are true pulse generators using all digital techniques. They can replicate the capabilities of traditional pulse generators whilst adding many additional facilities such as pulse modulations.As well as operating as pulse generators, the instruments can act as high performance noise generators and as function/arbitrary generators - making them truly universal waveform generators.
-
Product
Multifunction Counter (Pulse Input)
CM1-CT
-
CM1-CT multifunction counter(position) display controller, is design to have 2 pulse input, for proximity switch, photoelectric sensor, encoder etc.. Counting increase or decrease, positioning batch count etc.. display, with External input and Modbus communication port.Multiple types of input mode, trip mode setting to fulfil easy usage and requirement for counter controller. For different requirement, the meter can be with 2 relay or 1 Analogue output or 1 RS485(Modbus RTD mode) communication. (Choose 1 kind of output from the 3 options)
-
Product
Trip Amplifiers
-
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
Product
4-Quadrant Power Amplifier
PAV10000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Voltage Pulse Generator
LSG-65C
-
Shanghai Sanki Electronic Industries Co., Ltd.
The waveform parameters of the voltage pulse generator LSG-65C fully meet the requirements of IEC60065 and GB8898; the pulse voltage output of up to 10kV can meet the requirements of different test levels of users; the self-developed high-voltage electronic switch is adopted , which has high stability, low noise and long service life. Long; digital display mode, intuitive and easy to operate.
-
Product
Fluorescent Lamp Asymmetric Pulse Tester
UI2002C
-
UI2002C is designed according to the latest update in IEC 61347-2-3 about the test requirements for local rectifying effects on tubes. It imitates the condition when tube is under local rectifying status and tests the abnormal protection function of ballast by adopting fluorescent lamp asymmetry pulse test method with 3 windows for displaying rectified voltage, rectified current, and rectified power. It is easy for operation and with high test accuracy. • Measure lamp voltage, lamp current , average and total power of lamp. • Lamp voltage range: 10~300V • Lamp current range: 10mA~1.0A • Lamp power range: 0.5~300W • Tolerance is 5%
-
Product
30A, 50 MHz High Sensitivity Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP030B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Amplifier Module
LNAM-B
-
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
-
Product
Femtosecond Autocorrelators - Pulse Measurement Systems
Reef
-
The autocorrelation technique is the most common method used to determine laser pulse width characteristics on a femtosecond time scale . Del Mar Photonics autocorrelators have been specifically designed to measure the width of pulses from femtosecond lasers.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM-12
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Components - Power Amplifiers (FPA)
FPA Series
-
FPA series driver amplifiers and power amplifiers are discrete and/or MMIC pHEMT device-based amplifiers that operate over the frequency range 18 to 110 GHz for high output power applications. The amplifiers are offered in two categories, standard and custom built up to 250 GHz.The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration. The optional input and output integrated isolators are available to further improve the port return loss.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
-
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-12010A
-
High Power Pulse Instruments GmbH
The high-current TLP/HMM test system TLP-12010A offers advanced features intended for the characterization of semiconductor devices, discrete components, such as TVS, varistors, capacitors, gas tubes, circuits and systems in the high power time domain. It includes high current I-V characteristics inpulsed operation mode, turn-on/off transient characteristics of the device, breakdown effects, charge recovery effects e.g. reverse recovery, Safe-Operating-Area (SOA) and ESD measurements in general.
-
Product
Single Channel High Voltage Linear Amplifier
A400
-
The A400 is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of 200. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Module Type Amplifiers
-
Optical amplifier Gain Blocks are compact in size and suitable for built-in use. FiberLabs provides a wide wavelength range of optical amplifier Gain-Blocks over the O-, S-, C- and L-bands. These Gain Blocks can be used for B-PON system using three wavelengths of 1.31 μm, 1.49 μm, and 1.55 μm (ITU-T [compliant with G.983.3]), DWDM system and 100 GbE (IEEE 802.3ba) using the 1.3 μm band.
-
Product
Amplifiers
-
Fully automatic, legal limit plus headroom amplifierAlpha’s low-drive, tube amplifier design delivers the cleanest possible signalOperates on all Amateur Radio Bands 160M thru 10MSingle, easy to find, inexpensive 3CX1500A7 8877 type tubeInternal, automatic 4 port antenna switch capable of combining any 2 antenna portsAlpha’s Legendary service and support4 year limited warranty on hardware, 1 year on tube1500W, 100% duty cycle, no time limitation, key down foreverRugged construction built to last
-
Product
Pulsed And CW ESR/EPR: Quasi-continuous Powerful Millimeter (mm-wave) And Sub-millimeter (sub-mm Wave) Orotron Generator
-
Insight Product Company offers Quasi-continuous powerful millimeter (mm-wave) and sub-millimeter (sub-mm wave) Orotron Generators which can be used for both continuous wave (CW) and pulsed electron spin resonance (ESR) and electon paramagnetic resonance (EPR) experiments.
-
Product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
-
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
-
Product
Bi-directional Amplifiers (BDAs)
-
Triad’s legacy and expertise in amplifying long range, high data rate radio links has yielded many small and lightweight COTS BDAs that are simple to integrate, reliable, and rugged enough to pass any MIL-STD-810G test thrown at them. Our BDAs are the first choice for many radio system designs in applications where more RF power is required to create ultra-long range unmanned data links and other radio communications, and/or in applications that require the highest data throughput.
