Flux Density
See Also: Density, Hysteresis Loop, Gauss
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-154
The 40-297A-154 (PXI) and the 42-297A-154 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Electro-mechanical Relay Module, 75xSPST, Normally Closed
42-145A-101-NC
The 40-145A-101-NC (PXI) and 42-145A-101-NC (PXIe) 75xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-035
The 40-297A-035 (PXI) and the 42-297A-035 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 201 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
3U CPCI High Density I/O & Comm Board
75D4
NAI’s 75D4 is a 3U cPCI High-Density I/O and Communication Board with a single, high-density function module slot. In addition, the motherboard also includes an option for an integrated four-channel RS232/423/422/485 serial communication complement. This low-power/high-performance board is ideally suited for rugged defense, commercial aerospace, and industrial applications.
-
product
PXI High Density MUX BRIC, 96-Chan, 10-Pole
40-570-416
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 4-Channel, 32-Pole
42-614D-020
The 40-614D-020 (PXI) and 42-614D-020 (PXIe) 1-bank, 4-channel, 32-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 31.5Ω
50-298-010
The 50-298-010 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Very High Density Mux 5 Ch 32 Pole
40-670A-022-5/32
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI/PXIe High Density Electro-mechanical Relay Module, 100xSPST, Normally Closed
40-145A-201-NC
The 40-145A-201-NC (PXI) and 42-145A-201-NC (PXIe) 100xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-120
The 40-297A-120 (PXI) and the 42-297A-120 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Ultra High Density 4mm Reed Relays
120-1-A-5/2
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A5 V Coil
-
product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 1.51MΩ
40-298-050
The 40-298-150 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 32-Channel, 4-Pole
40-614D-017
The 40-614D-017 (PXI) and 42-614D-017 (PXIe) 1-bank, 32-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
192 X 4 / Dual 96 X 4, cPCI High Density Matrix Module
DP-cPCI-4149
Matrix switches are the most versatile type of switching system. Any input can be connected to any output, singly or in combination. A matrix switch simplifies the signal routing in an overall system, through reduced internal connection path.DP-cPCI-4149 offers ultra high density matrix in a single slot 6U sized cPCI module with flexibility to configure in the following ways:192 x 4 (Single- wire).Dual 96 x 4 (Single -wire).96 x 4 (Two-wire)DP-cPCI-4149 uses magnetically screened reed relays.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 472Ω
50-298-120
The 50-298-120 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 64-Channel, 2-Pole
42-614D-016
The 40-614D-016 (PXI) and 42-614D-016 (PXIe) 1-bank, 64-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
LXI High Density 50x50 2A Matrix with BIRST
60-552-921
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 102kΩ
50-298-040
The 50-298-040 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI High Density MUX 94-Channel 1-Pole
40-640-022-94/1
This series of high density multiplexer modules feature a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The multiplexer module is available as a 47-channel 2-pole, 94-channel 1-pole or 47-channel 1-pole with screened relays. Connections are made via a front panel 96-pin connector. It may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available for this 1-pole version).
-
product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-144
The 40-297A-144 (PXI) and the 42-297A-144 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 1.51 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 773kΩ
40-298-143
The 40-298-143 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-123
The 40-297A-123 (PXI) and the 42-297A-123 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-033
The 40-297A-033 (PXI) and the 42-297A-033 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 52.4 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
LXI High Density 32x64 2A Matrix with BIRST
60-552-023
It is constructed from 8x64 sub-assemblies, permitting the matrix to be supplied in a variety of sizes from a single 16 x 64 to 64 X 64 and dual 8x64 to 32x64. Larger configurations can be easily achieved by utilizing the Loop thru connections on either the X or Y bus, for instance, four 64x64 units can be linked to create a 128x128 matrix.
-
product
PXI Very High Density Multiplexer, 10-Channel 8-pole
40-670C-021-10/8
The 40-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
LXI High Density 384x8 2-Pole 2A Matrix With BIRST
60-555-026
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
PXI Very High Density Multiplexer, 5-Channel 16-pole
40-670C-021-5/16
The 40-670C-021-5/16 is a 5-channel, 16-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI Very High Density Multiplexer, 24-Channel 4-pole
40-670C-021-24/4
The 40-670C-021-24/4 is a 24-channel, 4-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).





























