Network Load
-
product
3U VPX RL Thermal Load Simulation Module
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
product
Network Management
FUSEMATE
FUSEMATE eliminates the risk of personal injury when replacing LV fuses.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Road Load Data / Durability
Vehicle Durability Testing and Road Load Data AcquisitionA road load data acquisition system from Dewesoft is a perfect vehicle durability testing solution for real-drive tests or tests on the road simulator test benches. Our advanced DAQ technologies will shorten time to test dramatically and make sure you get the correct measurements right the first time.
-
product
Network Analysis
Network analysis includes a powerful set of analytical tools that allow for simulation, prediction, design and planning of system behavior utilizing an intelligent one-line diagram and the flexibility of a multi-dimensional database.
-
product
Compression Load Cell
EST-20
Technopark Automation & Control
The EST-20 is an industry standard Compression Load Cell that can also be used in tension. This load cell can be supplied with load button and cup as well as ball and cup mounting options and is typically used on high capacity silos, hopper scales, batching systems, platform scales, force measurement and tension measurement applications. It is available in capacities from 1 ton to 50 ton.
-
product
Loaded Spectrophotometer
DSCD-900
DSCD-900 is a highly performance spectrophotometer with test caliber upward. The instrument adopts the geometric conditions of D/8 lighting and observation of CIE recommendations, integration of the full band LED composite light source, double beam optical system, ETC every-time calibration technology, spectral reflectance standard deviation within 0.08, maximum of colorimetric values ΔE*ab is 0.03, to provide all the necessary color formula. It could be widely used for coating, printing, textile, meet plastic, food, medicine, automobile field to meet customers’ measurement requirement.
-
product
Impedance Stabilization Network
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.
-
product
VME Load Card
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
product
Regenerative AC load function
61800 Series Optional Function
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
-
product
Electronical Load Board 3U CompactPCI (air cooled)
045-097
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Load Testing for Evolved Packet Core (ePC/VePC)
Flare
Linkbit Flare is designed for load testing of Evolved Packet Core (ePC) networks, and the upcoming VePC deployments. It is based on the technology initially develped for Linkbit functional testers, and as a result is extremely flexible.
-
product
Heat Exchangers RF Coaxial Loads
86500 Series
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
product
Programmable DC Electronic Load - (Economical)
63200E Series
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
product
Wireless Cmmunications and Networks
Fraunhofer Institute for Telecommunications
The Wireless Communications and Networks Division has been working on mobile and wireless radio communications solutions for more than 20 years. The work covers a wide range and ranges from information and network theory via channel measurements and radio channel modeling, algorithms and protocol design, systematic reviews at link, system and network level to prototypical implementations in demonstrators and field tests.
-
product
Wireless Networking Systems
ZigBee®
Silicon Labs is the vendor of choice for OEMs developing ZigBee networking into their products. The Silicon Labs ZigBee platform is the most integrated, complete and feature rich ZigBee solution available a family of Wireless SoCs, based on ARM Cortex processor and 2.4 GHz transceiver, together the most reliable, scalable and advanced ZigBee software and supported by best-in-class development tools.
-
product
Spring Loaded Contacts
ATE Probes, Pogo pins and Contact Pads. Gold-plated, spring-loaded, capable of thousands of cycles. Probes for Automated Test Equipment (ATE). Various height SMT contact pins. Flat SMT contact pads. Spring loaded contacts consist of a plunger (or head), barrel (or body), and a fully encapsulated fine spring, to provide the spring force required to maintain positive contact. All have a high durability, exceeding 10,000 mating cycles.
-
product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
product
Loadpin Load Cell
LP
Designed to replace pins or bolts that carry a loadStainless steel constructionCapable of 100% humidity, 30G mechanical shock and 5G vibrationUsed with clevises, or pulley shafts to monitor loadsCapacity 1,740 lbf
-
product
Photonic Networks and Systems
Fraunhofer Institute for Telecommunications
The Photonic Networks and Systems Division develops solutions for high-performance optical transmission systems for use in in-house, access, metro, long-distance and satellite communications networks. The researchers are focusing on increasing capacity as well as improving safety and energy efficiency. The department has the latest measurement technology, very well-equipped system laboratories, powerful simulation tools and the ability to carry out field tests.
-
product
Electronic Loads
Electronic loads are indispensable tools in several fields of electrochemistry, for example in the research of batteries and fuel cells. Using an additional external power supply you easily can extend an EL to a two-quadrant potentiostat you need e.g. in the field of electrolysis.
-
product
Low Voltage High Current DC Electronic Load
N62400 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N62400 series is developed based on NGI's years of experience in testing for fuel cell. It is with high accuracy, high reliability and high cost-effective. N62400 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
product
48V / 200 Amp Load
BD12-48P-24/12
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
product
Streamline Vector Network Analyzer, 100 KHz To 26.5 GHz, 2-port
P9375B
Compact, faceless, vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 26.5 GHz.
-
product
Millimeter-wave Test Set Controller For PNA/PNA-X Network Analyzer Series, 2- Or 4-port
N5292A
The N5292A millimeter-wave controller provides 2- or 4- port interface capability to the millimeter-wave frequency extender modules and with a PNA or PNA-X Series B model network analyzers.
-
product
Wireless Network Adapter
BR-310AC
BR-310AC is a high-performance wireless network adapter which enables any Ethernet device to become an 802.11a/b/g/n/ac dual band wireless network device, giving the freedom to place it anywhere in your facility.
-
product
1U Rackmount Network Appliance Platform With Intel® Atom® Processor C2558/C2758 Up To 2.40 GHz And 6 GbE LANs
NA361R
The NA361R is 1U rackmount network appliance platform for VPN, Firewall, UTM and other network applications. It supports low power Intel® Rangeley Atom™ Soc up to 2.4 GHz processor. The NA361R empowers its performance on Rangeley with 8 cores and supports Intel® AES New Instructions (AES-NI) and VT-x virtualization while the new Crypto Engine enables Intel® 4 x DDR3 UDIMM socket up to 32GB, unbuffered non ECC/ECC memory (dual channel) and QuckAssist Technology that supports 128, 192 and 256-bit AES, 3DES, DES. To prevent problems from sudden shutdown, the NA361R supports LAN bypass function through software program, and supports two 2.5" SATA HDD or one CompactFlash™ for storing event log data. It also supports one expansion slot for 1G or 10G NIC card for optional.
-
product
Network Operation Center Automation
VIRTUAL NOC
Automate 100% of the first-line Network Operation Center (NOC). With our closed-loop solution, network operators can automate the ticket handling process, reduce OPEX, time to action and improve customer experience.
-
product
Large Compressive Load Cell
CCLG-3.0
DLM’s range of Large Compressive load cells can be used independently or in combination as part of weighing platforms.
-
product
Programmable DC Load Current Waveform Generator
9923
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
