Non-contact Voltage Testers
check for presence of electricity.
-
product
AC and DC Current or Voltage Transducers
VT7 AND VT8 Series
The Model VT7 Series dc voltage transducer produces an output which is directly proportional to the input from dc to 10kHz. It functions as a millivolt dc shunt or a high voltage isolator to 1000V
-
product
AC-DC High Voltage Power Supplies
These modular High Voltage supplies may be used as constant voltage or constant current sources. They may be remotely programmed by means of either voltage or resistance, and have provisions for remote monitoring and output inhibiting. All control and monitoring connections are on a pluggable terminal block that functions as a connector, providing wiring convenience and permitting easy and rapid connect/disconnect. Outputs are arc/short circuit protected.
-
product
Multi-Network Cable Tester
3PK-NT007N
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
product
HiPot Testers
Testwave LLC has been selling, renting and servicing Hipot Products for over eight years.
-
product
Memory Tester
RAMCHECK LX DDR3
Quickly test DDR3 DIMM and SO-DIMM memory. In just seconds, RAMCHECK LX will perform a thorough test of the module and provide complete identification. Also tests expensive LRDIMM modules.
-
product
PXI High Voltage Multiplexer, 24-Channel
40-320A-101
The 40-320A-101 is a single 24-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
product
Adhesion and Peel Tester
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
product
Automated Headlight Tester
VLT 0936/MK2
Fully computerized controlled CCD Head-light Beam Tester, with fully automated vertical and horizontal movements, with automated searching of the hot spot of the beam. This robot type Headlight Beam Tester is connected to the Vehicle Test Lane Computer system and displays instructions and results to one of the large overhead SVGA monitors of the Test Lane.
-
product
Impulse Withstand Voltage Tester
SUG255
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
product
Automated Torque Tester
NJY-H5
NJY-H5 Automated Torque Tester is professionally suitable for testing the torque value of the caps of packaging products such as bottles, beverage bottles, mineral water bottles, and milk bottles. It is an ideal configuration instrument for offline or online testing of production units in the packaging industry.
-
product
Validation Testers
M Series
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
-
product
Tester & Programmer
TP-TACT
TP-TACT is designed to test the efficiency and program the operating range of electronic turbocharger controllers.
-
product
Primary Adhesive Tester
DRK129
Shandong Drick Instruments Co., Ltd.
DRK129 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
product
Motor Stator Tester
DZ901
Shanghai Aoboor Electric Co., Ltd.
Applicable to precision electrical properties test of stators of y-type three-ohase motors, single-phase motors, hub generators, brushless motors and servo motors.
-
product
Medical Leakage Tester
GLP2-CE
For testing the leakage current of medical equipment to standards EN 60990 + EN 60601.
-
product
Electrical Tester
T+Pro
Safer than solenoid testers and fully compliant with NFPA 70E, (when used properly per Article 110.4 Use of Equipment (A) Test Instruments and Equipment), the T+Pro helps electricians and technicians work safer by indicating the presence of voltage, even when the batteries are dead.
-
product
Continuity Tester
69133
Quickly reveals shorts or broken circuits in all types of electrical devices and controls.Tests for continuity of circuit with power off.Bulb in handle glows when circuit is complete (bulb included).Pointed 3-3/4'' (95 mm) probe gets right to the problem.Deluxe 4'' (102 mm) long handle with removable nylon cap holds replaceable bulb and battery.36'' (914 mm) test lead with alligator clip.Uses one AAA battery (not included).Replacement bulb (Cat. No. 69131)
-
product
Multifunction Installation Testers
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
product
Battery Testers
Battery testers are electronic devices designed to test the remaining capacity of a battery's overall charge.
-
product
Cone Penetration Tester
DRK8096
Shandong Drick Instruments Co., Ltd.
Determination of compliance with national standards GB / T26991, were compact design, LCD display, automatic data collection and the corresponding statistical calculations, measurement report printout.It can connect the PC output data.The entire testing process is very simple, in full compliance with the provisions of the State Pharmacopoeia. Accurate measurement results, which has good reproducibility, stability of the system.
-
product
Insulation Tester
AD-2025
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
product
HV DC Voltage Generators
Fivestar HV Testing Equipment Co., Ltd.
HV DC voltage generators are used to generate high voltage DC test voltages for routine, type and development test on components and complete systems found in electrical power supply systems and operating on DC voltage (HV transmission systems etc). There are K and M series, and available for indoor and outdoor.
-
product
Concrete Tester & Surveyor
CTS-02V4
CTS-02V4 (Concrete Test and Surveyor) is a Non-destructive testing device for estimation of compressive strength of concrete. CTS estimates the compressive strength of concrete based on Mechanical Impedance Method by measuring a waveform of impact force with an accelerometer which mounted on the hammer unit.
-
product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-01
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
product
High Voltage Detector
AC HotStick
High sensitivity voltage detector for emergency responders. The AC HotStick is a safety device designed for professional rescuers which provides warning of exposed high voltage AC from a safe distance.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
Anaerobic Jar Tester
LD-LAJ-A11
Anaerobic JarLD-LAJ-A11with 2.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.





























