Non-contact Voltage Testers
check for presence of electricity.
-
product
DMX Tester
DMXter4 RDM
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
product
Audio Circuit Tester
25500
Handy device for locating short and open circuits. Horn sounds when circuit is complete. Long 5 foot leads permit technicians to work around corners, under dash boards and in trunks. For use on all 6 and 12 volt circuits.
-
product
Digital Igniter Tester
Alpha 4314KRC
The Alpha 4314KRC Digital Igniter Tester packaged per NSN 6625-01-460-1499.
-
product
Digital Insulation Tester
SDIT300
ACV ; 600V. Safety standard ; IEC1010-1, IEC1557, CAT. 600V. Operating Temperature ; 0 to 40. Operating Humidity ; RH 70% MAX. Storage Temperature ; -10 to 50. Storage Humidity ; RH 80% MAX
-
product
Non-contact Sheet Resistance/resistivity Measurement Instrument With PC
NC-10 (NC-20)
*Easy operation and data processing by PC*No damage measurement by non-contact eddy current method*Replaceable probes by meas. range (*Second or more probe is for the option)*1 point measurement of center position*5 types of model for each measuring range*Temperature correction for silicon wafer function
-
product
Voltage Controlled Oscillators
World's widest selectionWideband up to full octaveLinear tuning
-
product
Polysilicon Resistivity Tester
HS-POSRT
HS-POSRT polysilicon resistivity tester is an advanced resistivity tester, it has features of wide resistivity measuring range, high testing accuracy, high stability, swift body and easy operation. It is a good friend to Siemens polysilicon material producer,SH4 polysilicon material producer, UMG polysilicon material poroducer and so on
-
product
Oxygen Index Tester
TESTEX Testing Equipment Systems Ltd.
Oxygen Index Tester, to determine the minimum oxygen concentration required for the combustion of a sample in the mixed gas of oxygen and nitrogen under the standard conditions.
-
product
Vacuum Switch Tester
KVZK
KV Hipot Power Test Equipment Co.,Ltd
KVZK Vacuum Switch Tester with an electromagnetic discharge measuring method is applied to measure the vacuum degree of vacuum switches.
-
product
Dual Channel High Voltage Linear Amplifier
F10AD
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
product
Shore Hardness Tester
Beijing TIME High Technology Ltd.
A device used to measure the hardness of materials like rubber, plastics, and elastomers by measuring their resistance to permanent indentation.
-
product
Non-contact Displacement Sensors
This is a flexible sensor that can be installed anywhere and is equipped with high environmental resistance enabling use in harsh environments.
-
product
Proximity Voltage Detectors
Verify the presence of voltage without contacting the conductor. Audible and visual alert when voltage is present. Powered by a rechargeable Li-Ion battery. HI/LO proximity voltage detector with two voltage ranges, 50V-4kV and above 4kV.
-
product
Voltage References
Renesas' wide selection of voltage reference (Vref) circuits offer accurate and stable reference voltages unaffected by external influences such as variation in temperature, input voltage and time.
-
product
AMIDA VCSEL Tester
AMIDA VCSEL tester can be divided into three parts: LIV measurement system, Near Field measurement system and Far Field measurement system. To achieve the above three measurements, in addition to the necessary optical components and optical instruments, the core technology is to provide fast and stable current pulses to drive the VCSEL laser diode to emit light, and then to test various optical and electrical properties
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Surge Voltage Generator
SSG 3000
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
product
Tablet Hardness Tester
* Complied with USP* Pretty design with an easy operation* The model can be rotated 180 degrees position to do an error calibration.* Sample diameter range: Ø3 ~ Ø30 mm* The model can double as a tensile tester.* Pressure gauge with a variety of specifications to provide choice.
-
product
Voltage Meter
MN3I
М-module МН3И is a mezzanine module designed to measure the instantaneous voltage value of high-frequency signals via 3 galvanically isolated channels from each other, control circuits and crate frame.
-
product
High Voltage Pulse
For thicker coatings such as coal tars, extruded and tape coatings, It has a range of infinite voltage settings from 1,000 to 15,000 volts. This wide range permits you to maintain a steady inspection rate on most types of coatings on most pipe sizes without changing detectors. Pulse voltage output only.
-
product
Low Operate Voltage Relays
DGG Series
Heavy duty relays wth extremely sensitive coil (pull-in 0,4 x Unom) for demanding applications.
-
product
WAN Tester II
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
product
Mechanical Tester
TriboLab CMP
Leveraging over 20 years of CMP characterization expertise with its predecessor product (Bruker CP-4), TriboLab CMP brings a complete set of capabilities to the industry-leading TriboLab platform. The resulting accuracy and measurement repeatability enables the highly effective qualification, inspection, and ongoing functionality testing required throughout the CMP process.
-
product
Tearing Tester
TGT-01
Jinan Leading Instruments Co., Ltd.
TGT-01 Tearing Tester is applicable in thetearing test of films, sheets, flexible PVC, PVDC, waterproof films, wovenmaterials, polypropylene, polyester, paper, cardboard, textile and non-woven,etc.
-
product
Pile Height Tester
TF630
TESTEX Testing Equipment Systems Ltd.
The flat stainless steel gauges are inserted into the pile, by using successive gauges, the gauge nearest the pile length can be determined. The measuring range is 3 to 25mm in 1mm steps.
-
product
Hydrostatic Testers
Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 30 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07. In addition to U.S. Military stock listed hydrostatic testers, we manufacture both standard and custom hose proof test stands, portable hydrostatic testers, hydrostatic test chambers and ancillary equipment to fit individual customers’ needs as required. We can typically ship standard units within 24-72 hours, sooner if required.
-
product
Rust and Corrosion Testers
Liquefied petroleum gas copper corrosion tester, lubricating oil rust characteristics tester, rust characteristics and corrosion tester, copper strip corrosion tester





























