-
Product
Friction & Peel Strength Tester
FPT-F1
-
FPT-F1 Friction Peel Tester can be used to test coefficient of static and dynamic friction of plastic films, sheets, foils, paper, cardboard, woven bags, fabric (fabric style test), metal-plastic composite belt for communication cable, convey belt and textile, as well as peel strength of adhesive laminated products, medical adhesive bandage, release paper and protective films.
-
Product
Hot Temperature Hardness Tester
1200C
-
Rtec high temperature hardness tester is used to do high temperature materials testing up to 1200C. To prevent oxidation of tip and the samples the high temperature indenter comes with sealed chamber with inert gas. High resolution programmable down force control and XY stage allows to do multiple indents on same or multiple samples with ease.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
Go No Go Testers
-
Go No Go Testers are developed in portable formats. Typically these are utilized at 'I' Level and 'O' Level test requirements and clear the aircraft LRU for flight.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
Thermal Sensitivity Tester
NTE-2A
-
The NTE-2A Thermal Probe is a sophisticated, non-invasive device for the clinical evaluation of neuropathy and the assessment of short fiber neurological function. Individual thresholds are compared to normals to statistical normals. These results provide an accurate means of tracking chronic changes in small fiber nerve function. It can be used for pain studies and in any application were a variable, accurately-controlled temperature stimulus is required. The NTE-2A is often used in conjunction with the Vibratron II to assess peripheral neuropathies.
-
Product
2 Ch Linear Vibration Motor Tester
BK2120C2
-
If it's not broke, break it. And when our BK2120C was a top selling product, we redesigned it. We took all the feedback from our customers and implemented it with a modular design to come up with a system that is more versitile, easier to use, and easier to set up. The core concept is the same; the BK2120C runs up to 4 vibration sweeps, which you define, to check whether your linear vibration motor is within the limits you set. And now you can set up your own feedback so it's even easier to determine the class of pass or the reason for failure. You still get fast, high quality testing for your linear vibration motors on the product line. And it's still versitile enough to be used for QA or QC as well.
-
Product
IK Level Tester
IK07-10
-
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
Product
Force Displacement Testers
-
Force displacement testing measures how much force is required to displace or deform a specific component or material. It’s an important aspect of quality control in manufacturing as well as material science. It’s necessary to help ensure products are made to the proper standards and to verify the properties of certain materials. Imada provides a range of force displacement testers that provide precise and accurate measurements, with numerous features to help technicians complete testing as quickly and effectively as possible.
-
Product
Quasar Smart Relay Tester
-
The Quasar is the most advanced three-phase relay test set designed for the testing of secondary and IEC-61850 protections of any type with special focus on industrial and routine maintenance applications.
-
Product
Display Tester
-
Yuyao City Yinte Neon-Electroscope Factory
This neon-electroscope is applicable for directly detection of 12-240V zero line indirect detection of DC.
-
Product
Downloadable PAT Testers
-
Whether you are PAT testing in house on a regular basis or an electrical contractor testing 1000's of items a week, we have a downloadable PAT tester to suit your testing requirements.
-
Product
Multi Function Automobile Tester
6521
-
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance and power providing testing.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Mask ventilation resistance and pressure differential tester
WKS-3102
-
Mask ventilation resistance and pressure differential tester is used to measure the inhalation and exhalation resistance of mask under specified conditions. Applicable to mask manufacturers, labor protection equipment inspection agencies to carry out related testing and inspection of mask products, mask breath resistance tester, breathing valve air tightness tester, breath resistance machine for measuring respirator and mask protection products in Inspiratory resistance and expiratory resistance under specified conditions.
-
Product
Endurance Tester
-
Premier's Endurance Tester, also known as on-off tester and life tester, is used to perform the life test of the unit. The Endurance Tester, switches on the unit for a set time and then turns it off for a set time. This entire cycle is repeated multiple times, to simulate the behavior of the unit under extended use
-
Product
Static Soil Tester
GEO-probe
-
The complex is implemented on the basis of a portable computer and the CompactRIO control and measuring system. The software for recording and displaying measured signals and control of measuring equipment is developed on LabVIEW. The second modification of the measuring system includes, developed by our company, a miniature digital measuring module of a strain gage with a built-in ADC and inclinometer and a USB interface for connecting the digital measuring module of the probe to the computer.
-
Product
Digital Clamp Tester
M-1800
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*80mmφCT window and wide AC current measurements from 0.1A to 1000A.*DCmV analog data output for recorder.
-
Product
Primary Current Injection Tester
SLQ
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
It's a high voltage generator insutrment for tesitng.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Semiconductor Testers
Test Instrument
Our integrated team of semiconductor test innovators delivers a complete system tailored to achieve your specific objectives, incorporating:Test strategyHardware designSoftware development and integrationManufacturingInstallationProgram managementOngoing support
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
Product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Hipot Testers
-
We've been manufacturing hipot testers for over 75 years & have supplied many of the worlds leading manufacturers instruments with features that satisfy every type of requirement
-
Product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
-
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
Product
Waterproof pH Tester
pHTestr 10BNC
-
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
Product
Electrical Safety Testers
STW-9900 Series
-
* 500VA AC Test Capacity* 240 x 64 Ice Blue Dot Matrix LCD* Manual/Auto Mode* Function Key for Quick Selecting* High Intensity Flash for Caution & Status Indication* Safety Interlock Function* Zero Crossing Turn-on Operation* Zero Crossing Turn-on Operation* True RMS Current Measurement * High Resolution : 1μA for Measuring Current, 2V for Setting Voltage* PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing* Max. 100 Memory Block for Test Condition (Step) Setting. And Each Step can be Named Individually* Remote Terminal on the Front Panel for“Start”and“Stop” Control by External* Interface: RS-232C, USB Devise, Signal I/O and GP-IB (Option: OPT.1)
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Product
Solenoid Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
Product
Masks Particle Filtration Efficiency Tester
-
Sataton Instruments Technology CO., Ltd
Face masks particle filtration efficiency (BFE) tester is device to determine the particle filter penetration and filtration efficiency for respiratory protective devices and face masks. The tester with particle generator can provide sodium chloride particles and paraffin oil particles. It can measure the particle penetration, filtering efficiency and the breathing resistance delta P. It is widely used in quality control, research and development, certification, manufacturing or testing industry, etc.
