-
Product
BH Curve Tracer
6700BH Series
-
This BH curve tracer is adopted pole coil measuring method. The limit of size and shape for measuring work is very little and it can measure the difference of both face and reverse side of magnet.
-
Product
Impulse Cable Tracer
Wayfind'r
-
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
Product
IV Curve Tracer
IVCT
-
In recent years, we have been developing a sophisticated IV curve tracer for PV modules including a maximum power point tracking (MPPT) function. The IV curve tracer is designed for operation with any market-available steady-state solar simulator. Through our web-based software design, the operator can supervise the test results from every computer in a company network. The software contains functions such as an irradiation sum counter that helps to check requirements stated in a stabilization test like they are defined in IEC 61215 (MQT 19). We have also included a correction function to correct the traced IV curves to standard test conditions (STC) when the user enters the required temperature coefficients. One of the most important features is the multi-IV curve tracing function, which enables the user to display more than 150 IV curves in one graph. This eases the analysis of the weakest cells in hot-spot tests, which are required in IEC 61730 (MST 22) and IEC 61215 (MQT 09).
-
Product
Cable Tracer Prober M-CTP-240A
Cable Tracer Prober M-CTP-240A
-
Fuzhou Metricu Technology Co Ltd
Cable Tester, network tester
-
Product
Hysteresis Loop Tracer
MESA
-
The MESA is the only hysteresis loop tracer on the market that can make measurements in the frequency range of 10 Hz and below. Competing units operate with more-easily generated 60 Hz drive fields, and can have errors of as much as 30% in coercivity (Hc) measurements.
-
Product
Wires and Pipe Locator
LKZ-720
-
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
Product
Wire Mount Testers
-
Is designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
Product
Curve Tracer
CS-3000 Series
-
CS-3300 / CS-3200 / CS-3100 three model line-up. Maximum peak voltage: 3,000V (high-voltage mode for all models) in CS-3000 Series.Maximum peak current: 1,000A (CS-3300 high-current mode). The CS-3000 Series are CE-marked and UL listed.
-
Product
Parameter & Device Analyzers, Curve Tracer
-
Precision Current-Voltage Analyzer Series ensures accurate and efficient current-voltage measurements that give a clear insight into IV characteristics across a wide range of applications. The powerful characterization software and integrated source and measurements units (SMUs) make it much quicker and simpler to obtain accurate IV characterization. The EasyEXPERT group+ software supports all the characterization tasks such as measurement setup and execution, data analysis, data management and protection and so on, using the graphical intuitive user interface and mouse/keyboard operation. The Series provides a wide selection of IV analyzers suitable to your specific measurement needs in the range from an economic model to the most advanced analyzer capable of supporting cutting-edge applications.
-
Product
Precision Curve Tracer
CurveMasterTM
-
The CurveMasterTM delivers new price/performance efficiency to curve tracing and Failure Analysis. Curve trace has been a standard feature in our full-power chip tester for years, so the CurveMasterTM is built with today’s components and technology. With all new high-accuracy DC Parametrics, you’ll enjoy the most powerful curve tracer you have ever used.
-
Product
Benchtop Wiring Analyzer
2115
-
The Model 2115's compact size makes it the ideal choice for many benchtop or portable test applications. The small size does not mean you sacrifice any functionality. The 2115 delivers a full 1500 volt isolation and 2 amp continuity test stimulus. With the optional AC breakdown test providing 1000 VAC test stimulus, you will meet all test requirements.
-
Product
Semiconductor Curve Tracer
CS-8000 Series
-
The CS-8000 series are equipped with a high-voltage source of up to 5 kV and a high-current source of 2 kA. It features Pulse output, Gate pattern, and very small current measurement capabilities, and it supports the design evaluation of wideband-gap semiconductors such as SiC and GaN.
-
Product
Handheld Wiring Analyzer
HT-128+
-
Reduce your wire harness assembly and installation difficulties now. The NEXU HT-128+ test platform provides a valuable tool for multi-point wiring continuity analysis. Our versatile, lightweight, handheld unit can serve your wiring test and maintenance needs from harness layout to product field support. The HT-128+ performs testing and troubleshooting, automated ring-out, directed assembly plus other features to resolve wiring issues quickly to achieve increased product availability!
-
Product
Thermocouple Cable / Wire
-
Labfacility offer a wide range of thermocouple, PRT and extension cable / wire in stock for immediate despatch. Thermocouple cables are available in IEC or ANSI colour codes. Insulation types include PFA, PTFE, PVC & Fibreglass.
-
Product
Temperature Wire And Cable
-
Omega’s temperature wire, cable, mineral insulated cable, heating wire and cable offer covers all your needs for measuring and managing temperature. Take a closer look for the right product for you.
-
Product
Wire Harness Tester
NX Pro
-
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
Product
Wire Abrasion Tester
SG-D03DG
-
This machine is mainly based on UL1581 / UL83 standard abrasion test wire and cable testing requirements .
-
Product
Power Device Analyzer / Curve Tracer
-
The B1505A Power Device Analyzer / Curve Tracer is focused on the needs of power device manufacturers, while the B1506A Power Device Analyzer for Circuit Design is focused on the needs of power electronics circuit / product manufacturers. The B1507A Power Device Capacitance Analyzer helps both power device development engineers and power circuit designers maximize product value by revealing device capacitance characteristics.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
MTA Wiring Analyzer
2650
-
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
Product
Resistance Wire Bonding
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
-
Product
Wire and cable slicer
CX-18
-
Shenzhen Chuangxin Instruments Co., Ltd.
Wire and cable slicing machine is a kind of used products factory la bequipment. Using mechanical transmission feed, blade cutting structure, it can be cut1 to 12 mm range plastic various thickness, sheet material, etc., they are availablRubber, leather material and hardness of the material must be sliced, the machine is widelyUsed in rubber, plastic, leather, electric wire, cable, scientific research units, etc.
-
Product
Parametric Curve Tracer Configurations
Keithley PCT
-
Developing and using MOSFETS, IGBTs, diodes and other high power devices requires comprehensive device-level characterization such as breakdown voltage, on-state current and capacitance measurements. Keithley's line of high power Parametric Curve Tracer configurations supports the full spectrum of device types and test parameters. Keithley's Parametric Curve Tracer configurations include everything necessary for the characterization engineer to develop a complete test system quickly.
-
Product
4 Wire Earth Resistance Testers
2734 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled with advanced safety features.● 4-wire testing only.● Automatic C spike check.● Auto power-off.● Auto data hold.● Large LCD (2000 counts).● Protective terminal cover.
-
Product
PV Analyzer I-V Curve Tracers
-
The Solmetric line of PV Analyzer I-V curve tracers are widely used in Commissioning, Auditing, O&M, and Troubleshooting of PV systems.
-
Product
Multi-purpose Cable Tester and Cable Tracer
165 CB
-
Standard Electric Works Co., Ltd
165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.
-
Product
Hipot Wire Harness Testers
NX Hipot
-
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
Product
Gauge Type T Thermocouple Wire
W-TW-24
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
4 Wire Earth Resistance Testers
4234 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth testing at 2Ω, 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test.● 3-Wire test.● 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● Robust, compact and easy-to-carry.
-
Product
Wire Damaged Tester
WDT-1
-
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
