-
-
product
Active Voltage Probes
Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the active voltage probe becomes the everyday probe for all different types of signals and connection points.
-
product
IC Tester
ICE1
The IC Test System was developed to measure the EMC behavior of circuits (ICs) in the event of targeted field or line-related interference and for measuring emissions. The test IC is tested in function. The test environment ICE1 creates the functional environment of the test IC. The respective measurement task is carried out with the corresponding probe set.
-
product
Standard 0.79 (23.40) - 1.75 (49.60) High Frequency Probe
CSP-40G-021
Your product description goes here.
-
product
Logic Analyzer Probe, 20 MHz, 4VDC to 18VDC
72-190
A compact and lightweight probe for the analysis and troubleshooting of logic circuits. The probe will recognise high, intermediate and low level pulses in DTL, TTL, HTL and CMOS logic circuits. Works as a pulse detector, pulse stretcher and a pulse memory.
-
product
Antenna Kits
A.H. Systems offers 10 models of portable antenna kits. Each kit provides all the reliable antennas, current probes and accessories needed to satisfy a wide array of customer requirements. Each component has a specific storage compartment in the carrying case therefore, loss and breakage are virtually eliminated. Cables, a tripod with azimuth and elevation head and a tripod carrying case accompany each antenna kit. Click on a model below to learn more about it''s characteristics and included antennas.
-
product
Benchtop Test System
300 Series Benchtop ATE
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
-
product
6-12V Heavy Duty Circuit Tester With Long Probe
1668A
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. To indicate whether there is an electrical potential at any low voltage point in the system. By using the pointed contact tip to pierce insulation on cables, it will also indicate if current is present. This can be helpful when tracing faults or add cable to a circuit.
-
product
Ultra High 1.16 (33.00) - 9.70 (275.00) Long Travel Bead Probe
BPLT-25C-9.7
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
product
2kV, 120 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3206A
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
Ultra High 3.38 (96.00) - 10.00 (283.00) Bead Probe
BTP-72HC-10
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,700Overall Length (mm): 43.18
-
product
Deluxe DMM w/Amp Shutters
582
*Huge 2 inch LCD Display, easy to see from across the room *Display is backlit for use in Dark Spaces *Amp Shutters prevent mistaken operation, improve safety and saves fuses by blocking unused amp jacks! *Great Meter for Electrical Trouble Shooting *11 Test Functions, 33 Test Ranges *Measures Temp in Both F and C, Probe Included *Desireable 20 Amp Test Range *Modern Design, the Protective Holster is Built-In *Data Hold *Carrying case, Test leads, Temp probe, Instructions and Battery included
-
product
AFM Atomic Force Microscope
FM-Nanoview 6800
Zhengzhou Nanbei Instrument Equipment Co. Ltd
All-in-one design, smart structure and shape.Scan head and sample stage are designed together, strong anti-vibration performance .Precision laser detection and probe alignment device make laser adjustment simple and easy.Adapt servomotor to drive the sample approaching tip manually or automatically, to realize precision scanning area positioning.
-
product
Y Lead Adapter for ZD Differential Probes Qty 1
PACC-ZD001
Y lead Adapter for ZD differential probes Qty 1
-
product
Alternate 0.66 (19.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-62H-6-S
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
-
product
Probes And Cables
The iProbe is an intelligent temperature sensor that can be calibrated independently of SBIR’s blackbody systems or 104i precision thermometers. These ultra-stable, highly responsive iProbes are used to provide long term accuracy and repeatability of under 0.010°C. Each iProbe incorporates onboard flash memory that allows all calibration constants and calibration date information to be stored independently of the blackbody or thermometer system. This allows iProbes to be exchanged for use on a blackbody or thermometer without any loss in stability or accuracy. To re-calibrate a system you need only exchange the current iProbe with a recently calibrated one. No special equipment is required and there is no down time in the test area.
-
product
Standard 2.20 (62.00) - 4.80 (136.00) General Purpose Probe
EPA-4A
Current Rating (Amps): 7Average Probe Resistance (mOhm): 35Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,320Overall Length (mm): 33.53
-
product
In Line HT Ignition Tester
1177
Establishes whether there is a high tension spark potential at the spark plug. Hands free operation means no risk of electric shock to user. Ideal for modern vehicles with sensitive electronics. Probe is 55mm long with a lead 100mm in length.
-
product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1L24-4
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Borescopes
Displays clear images through a flexible camera probe. It is useful for viewing details of automobiles engine, pipelines, inner building walls, drain pipes, and other hard to reach locations.
-
product
Multimeter Electronic Test Leads Kit
VERSATILE KIT includes 2 alligator clips with removable insulation, 2 extended range plunger mini-hooks with pass-through banana plugs, 2 heavy duty test probes, 2 42” lead extensionsUNIVERSALLY COMPATIBLE with either 0.16” banana plugs or shrouded banana plugs on all ends
-
product
Line Automation Equipment
5000 Series In-line Handler
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
product
Automotive Fuse Current Probe
FUSE PEEKER
Automotive Diagnostics and Publishing
Automotive Fuse Peeker Current Probe for Testing Injectors, Coils, Solenoids and most components. The FUSE PEEKER Automotive Fuse Current Probe works with your own scope, the Auto Scope 1 or any other type of oscilloscope. It uses magnetic sensor technology, which is accurate and safe for your tool. It can detect small amounts of current as small as 5 milli-amps.
-
-
product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-1Z1-10
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Light Probes (LED-Test)
As the original inventors of light probes for in-circuit color and intensity test of LEDs, our business partner Optomistic Products has been a leader in LED test for over 20 years, providing LED solutions to customers worldwide. Our unique patented LED test solution offers unparalleled reliability and is widely accepted by the LED test industry.
-
product
BGA Interposer, LPDDR4 200-ball, 2-wing For Logic Analyzer, Connects To 61-pin ZIF
W6601A
The W6601A LPDDR4 2-wing BGA interposer for LPDDR4 200-ball BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A logic analyzer module it is compatible with. The W6601A is the smallest BGA interposer for LPDDR4 200-ball DRAM capable of capturing simultaneous read and write traffic at data rates in excess of 3.2 Gb/s. U4208A and U4209A probe/cables connect W6601A LPDDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W6601A BGA interposer wings. Refer to the W6601A data sheet for complete list of LPDDR4 signals probed with the W6601A.
-
product
Carbon Monoxide Analyzers
706
Test Products International, Inc.
The 706 is an advanced state-of-the-art carbon monoxide (CO) gas analyzer designed to provide part per million readings from 0- 10,000 ppm. The 706 is capable of performing ambient as well as flue gas checks with its hot air probe and internal pump.
