DC Sources
A highly repeatable and stable DC voltage and current source.
-
product
Noise Source Family
347
The R347B waveguide noise source cover the R-band (26.5 to 40 GHz frequency range), while the Q347B model cover the Q-band (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices.
-
product
AC / DC Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
For the separation and conversion of sinusoidal and non-sinusoidal alternating currents and voltages into standard signals. TRMS Education / True-RMS. Calibrated switchable versions with Weitbereichsnetzeil and high working voltage up to 3600 V AC / DC.
-
product
Multichannel Source Measurement Unit
AXS7720
Extremely low noise with linear output stageVery fast rise and fall timesProgrammable current pulseIntegrated current measurement unitIntegrated voltage measurement unit
-
product
Microwave Noise Source Generators
Noise Sources supply white gaussian electronic noise. The output is a flat instantaneous broadband electronic random noise. The noise source converts a DC input to noise. Units are available in bands between 10MHz thru 26.5 Ghz.
-
product
Broadband Coaxial Noise Sources
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
product
Programmable DC Power
TS Series
The TS Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power''''s rugged current-fed power processing, enables confidence in even the most demanding applications.
-
product
VCSEL Light Source
ams supplies LiDAR systems with specific light sources, called VCSEL (Vertical Cavity Surface Emitting Laser). These VCSELs offer specific advantages over other types of light sources as for instance Edge Emitter Lasers:
-
product
DC Electronic Load
EE30180A
The EE30180A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running.
-
product
Light Source
pE-300white
CoolLED's pE-300white offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. The pE-300white Light Source can be fitted directly to the microscope or specified with a liquid light guide. The system is a mercury-free alternative that is safer, more controllable, and repeatable than conventional high-pressure gas discharge illuminators. Spectral coverage is from the UV (DAPI excitation) to the Red region (Cy5 excitation). The system is perfect for hospital and regular research laboratory environments.
-
product
Relay Testing Voltage Source
PTE-FCN
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
product
Bench-top Optical Light Source
STC-BTOLS2201 series
Shanghai Stone Communication tech Co., Ltd
STC-BTOLS2201 series high stable Bench-top light source are microprocessor controlled laser diode sources which can support the variety of emitters such as: DFB,FP,PUMP,SLED etc. It is specially used in passive components testing, power meter calibration and general laboratory uses.
-
product
AC And DC Motors
Omega's AC and DC motors are built to deliver reliable long-term performance. With a variety of models available, we have motors for all your application's needs.
-
product
Open Source Logic Analyzer
Logic Pirate
8 channels 256,000 Samples recording size 20 MHz sampling speed, can potentially be overclocked to 60 MHz No compromise on sample size when combining different speeds or number of channels Simple configurable edge detection triggers on all inputs (simple OR trigger) Configurable ratio of samples from before and after the trigger (rolling sample buffer) 5 V tolerant inputs (LOW-level voltage < 0.8 V, HIGH-level voltage > 2.0 V) About 500 kB/s transfer speed to the PC (256 kSamples take about 0.5 seconds) Data capturing can be stopped from the host software anytime Cross platform host software for Windows, OS X, and Linux DIY-friendly 0603 parts and SOIC packages used on a 2-layer board On board 3.3 V regulator can supply up to 400 mA to an external circuit Tiny 3cm x 3cm PCB Firmware updates via built-in USB bootloader Probe cables and acrylic case available from Seeed Studio Open source PCB (EAGLE) and firmware files
-
product
Light Sources
Fiber optic light sources are a low-cost way to analyze and identify accurate fiber optic readings, while certifying optical fiber. Receive the ability to measure fiber optic light continuity, loss, and quality of the signal.
-
product
Dual Filament Source
Get the optimal thermal profile for different materials and situations with the Veeco Dual Filament Source. This source is designed for growing high-quality Ga- and In-containing materials, while preventing charge material recondensation and significantly reducing defects. Dual Filament Sources are available for use with both SUMO and conventional crucibles (including Group III production crucibles).
-
product
Multi-Channel, Programmable Current Source
CS-48-100
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
product
Module Type ASE Light Source
Module type ASE light sources are small in size and easy to integrate into equipments. The dimensions are different between models, and five sizes are available from the smallest MSA to S, M, M2 and L. All of them are operated on 5 VDC and the optical properties are the same as the corresponding bench-top models.
-
product
Sound Source And Power Amplifier
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
product
Brushless DC Motors
CAES offers brushless DC motors in 2 or 3 phase and with optional commutation.
-
product
Portable Light Sources
FOD 2113
The FOD 2113 provides three wavelengths: 1310&1550 nm in one port and 850 nm 10mW in another port. Available adapter types: FC, SC, ST, Universal 2.5mm. All adapters are changeable
-
product
3-Phase Programmable AC Source
61700
Chroma Systems Solutions, Inc.
Power: 1500VA, 3 (61701); 3000VA, 3 (61702); 4500VA, 3 (61703); 6000VA, 3 (61704); 12000VA, 3 (61705)Voltage: 0~150V/0~300VFrequency: 15~1.2KHzPhase angle: 0~360Built-in PFC, provides input power factor over 0.98Advanced PWM technology delivers high power density in a compact rack-mountable packageBuilt-in output isolation relaysAC+DC output modeProgrammable slew rate setting for changing voltage (optional function)Turn on, turn off phase angle controlUser-definable power-on statusPower line disturbance (PLD) simulation capability (optional function)Comprehensive measurement capability: V, Irms, Ipk, I inrush, P, PF, CF of current etc.Programmable r.m.s. current limitFull protection: OP, OC, OV and OT protectionGPIB and RS-232C interface (optional)Easy-use software for operation
-
product
DC Power Supply
PW-3063R
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-3063R as high as 0.1v and 0.01A.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
product
DC Power Products
West Mountain Radio offers a variety of power management devices to protect both the radio equipment and the power systems they are connected to. These devices provide both battery charge management and load management features. They are for public safety, commercial, marine and amateur radio applications. All products designed and tested by Ham radio operators.
-
product
Blackbodies & Extended Area Sources
The Infinity Series of blackbody radiation sources and extended area sources combine leading edge technology with features that support the expanding test requirements of the latest high performance sensors. SBIR designs the most stable, uniform, accurate and highly emissive blackbodies available. SBIR now offers VANTABLACK®S-IR as an optional coating, providing the E-O test community an unprecedented flat plate source emisisivty. SBIR continues to offer blackbody systems that provide the test community with unequaled performance, reliability and ease of integration into test systems. Our blackbody family includes six different varieties to choose from. The Infinity line offers four types of precision blackbody systems and our extended area sources offer two additional types of precision blackbodies to support all levels of IR testing.
-
product
DC Power Supplies
DCS Series
AMETEK Programmable Power, Inc.
The DCS Series of 1 kW, 1.2 kW and 3 kW programmable power supplies provides a highly reliable power platform. It utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a low profile chassis. This DCS power supply family has an easy-to-use front panel with 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and over voltage protection, status and constant-voltage/current mode operation. The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/local programming and preview status of voltage, current and OVP setpoints.
-
product
AC Power Sources
Test basic AC power with confidence using the most stable, reliable AC power sources More effectively simulate and analyze high-performance AC environments with built-in measurement capabilities Lower your cost of ownership with global support and the longest standard warranty in the industry
-
product
Blackbody Sources
Gemini R Model 976
The Gemini R comprises a blackbody with which radiation pyrometers (infrared thermometers) can be calibrated. The temperature of the cavity can be set to 0.1C over the temperature range 30C to 550C.
-
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
High-Standard Bench-Top Laser Source
Shanghai Stone Communication tech Co., Ltd
These bench-top laser source has built-in high-feature Semi-conductor laser device, it is the SM output, with less than 10MHz plus width. Based on the advanced micro-processor control system, this instrument integrated high precision ATC and ACC(APC) to control the electric circuit, in order to realize the high stable output of the laser device, and make the operation easily and directly. We also can provide user required communication port with the software to realize remote control from the PC.
-
product
Source Phase Control
S93088B
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
