Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
Analog and Other I/O
-
Our I/O portfolio covers everything from simple discrete to high speed analog control and delivers flexibility, performance, reliability and connectivity.
-
Product
Provides 3 Wire Voltage Output
SEM1620
-
The SEM1620 signal conditioner provides a 3 wire isolated voltage output signal and accepts RTD, Thermocouple, mV and passive current sensor inputs
-
Product
GPIB Analog Interface
Model 4861B
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
PCI-6510, 32-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated Digital I/O Device
779081-01
Digital I/O Module
The PCI-6510 is an industrial digital input interface, with a single bank of isolated channels. If a computer or application fault occurs, the PCI-6510 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Four outputs FTTB CATV optical receiver
B9428
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai B9428 product series, 47~862MHz operate bandwidth, output level Vo=88dBμV ( Pin=-2dBm ), suitable for FTTP optical fiber access network, which is a low power consumption, high performance, and excellent cost performance RFTV broadcast network ONU(Optical network unit). This series of product adopts high sensitivity receiving tube and Huatai special low noise matching circuit Under 3.8% modulation, when transmitting in full channels and with receiving power of -10dBm, the CNR can still reach high index of 45dB. Therefore, if adopting B9428, it is only need very low optical power to reach 45dB CNR required by the user.
-
Product
300W to 400W - Single Output
EFE Series
-
*Open frame, U channel, Cover options*High Efficiency*Active Power Factor Correction*Universal input (90 - 264VAC)*High peak loading capability*Suitable for 1U applications
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
7-Ch Thermocouple Input Module
ADAM-5018
Temperature Input Module
Accuracy Bandwidth: ±0.1% or better, 13.1 Hz @ 50 Hz, 15.72 Hz @ 60 HzSampling Rate: 10 samples/sec. (total)High Common Mode: 2000 VDCIsolation Voltage: 3,000 VDCFault and Overvoltage Protection: Withstands over voltage up to ±35 VCMR @ 50/60 Hz: 92 dB minInput Impedance: 20 MΩ. (Build-in 120 Ω Register for Current Input)Built-in TVS/ESD ProtectionFilter function: Yes
-
Product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 3 Bus Matrix Inputs
40-569B-113
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-113 is a 8 slot module fitted with 3 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
783731-01
Current Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 … includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
Product
25W to 200W - Single Output
LS Series
-
*Superior op. temp. performance up to 70 °C*Very High efficiency up to 87%*Very low cost*Compact Size*Withstands 300VAC surges (5s)*Convection or fan cooled (LS200)*Five year warranty
-
Product
Modular Analog & Digital Systems Solid-state, Digital and Relay Modules
G2T Series
-
Universal Switching Corporation
Our Series G2 product family is a field proven and versatile modular platform for both signal switching and distribution. Numerous digital and analog configurations and modules are available for a cost effective and compact solution.
-
Product
16-Ch Digital Input Modules
ADAM-5051
Digital Input Module
Input voltage: 30 VmaxCircuit type: Pull-Up current: 0.5 mA (Source Type)Power consumption: 0.53 WChannels: 16
-
Product
Infiniium V-Series Oscilloscope: 13 GHz, 4 Analog Channels
DSAV134A
Oscilloscope
13 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Oscilloscope, 500 MHz Bandwidth, 4 Input Channels, 50 Mpts/ch, 10 GS/s
HDO6054B
Oscilloscope
500 MHz, 4 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch High Definition Oscilloscope with 15.6" Display.
-
Product
Analog Meter
-
An electromechanical device that measures and displays physical quantities—such as voltage, current, resistance, or temperature—by using a needle (pointer) that moves across a calibrated, numerical scale.
-
Product
Analog Voltmeters
-
*Dual stick MARK series measure voltage and perform phasing operations from 0V to 75kV*No batteries or calibration required*Determines in-phase or out-of-phase*Determines underground cable faults*Discharges underground cables and other equipment that hold capacitive charges*Versatile for overhead and underground applications
-
Product
Infiniium V-Series Oscilloscope: 20 GHz, 4 Analog Channels
DSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Transforming Analog Circuit Breaker Testers
MAC-21
-
The MAC-21 uses proven microprocessor and A/D converter technology to provide real-time waveform analysis. This ensures accurate true-RMS readings of current pulses, even with DC offset and distortion, which are typical in primary injection testing. Intelligent threshold algorithms provide accurate trip time measurement. Integration of measurement and control functions allow advanced features such as preset on times, auto ranging, and optional printer or computer interface.
-
Product
80W Triple Output Power Supply, 6V, 5A & 25V, 1A
E36311A
Power Supply
The 80-Watt E36311A is a clean reliable bench power supply for general purpose applications. It combines convenient benchtop capabilities with flexible system features in a compact intuitive package. This is the most basic of the three models in this product family. For more advance capabilities such as data logging, output sequencing, list mode and auto parallel/serial explore the E36312A (80 W) and the E36313A (160 W) models.
-
Product
Oscilloscope 59 GHz, 4 Channels, 1mm inputs
UXR0594BP
Oscilloscope
The UXR0594BP is the 59 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
Analog Control Cable for Electronic Loads
EE105T-xx
-
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Product
8-Channel Relay Output Board With Housing for Mounting on a DIN Rail
PX8500-G
-
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3016-8
-
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-8-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2 GHz, 4 Analog Plus 16 Digital Channels
MSOS204A
Oscilloscope
2 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.5 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
Mixed Signal Oscilloscope 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014G
Oscilloscope
The MSOX3014G 100 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Analog Multiplexer Board
104-AIM-32
-
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
Product
SparkFun Analog MEMS Microphone Breakout
ICS-40180
-
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield.
