Up Converters
Increase the frequency of a signal.
-
Product
Ethernet To Fiber Optic Converters (Point To Point)
-
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
Single Phase Converter
Series Sirio AC / ACS
-
The SIRIO single-phase equaliser is an electronic device that offers the ability to regulate the rms value of a sinusoidal voltage through the control of two diodes connected in antiparallel.
-
Product
UPS (Uninterruptible Power Supply)
-
The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.
-
Product
Waveguide Electromechanical Relay Switches C, X, Ku, K & Ka Bands up to 40 GHz
-
Waveguide Electromechanical Switch models cover C, X, Ku, K, Ka frequency bands up to 40 GHz. SPDT and Optional DPDT* Configurations with Latching Self Cut-Off Actuators, TTL Logic, and Position Indictors with manual override. Patented Motor Drive with Arc Suppression. Designs support WR-137, WR-112, WR-90, WR-75, WR-62, WR-42, and WR-28 waveguide sizes with O Rings for pressurized operation. Power handling capability up to 12 kW CW and 320 kW Peak. These waveguide electromechanical relay switches deliver desirable performance that includes high isolation levels up to 105 dB, and extremely low insertion loss down to 0.01 dB.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, High Voltage Outputs
M2P.6576-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
D/A Converters
-
Renesas' high-speed, low-power, digital-to-analog data converters (DAC) are ideal for communication systems, medical/test instrumentation and equipment, and video applications.
-
Product
Modbus to DeviceNet Converter
D485
-
The D485 Modbus to DeviceNet Converter acts as a gateway between a Modbus RTU network and a DeviceNet network. Integration of Modbus devices into DeviceNet networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations.
-
Product
DC/DC Converter 3.5 W
REM3.5E-1224S/R6/A/SMD
-
DC/DC converter with 3.5 W from Recom | input ranges 9 - 18 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
Product
PXIe-1083, 5-Slot (5 Hybrid Slots), Up to 2 GB/s PXI Chassis
787026-01
Chassis
PXIe, 5-Slot (5 Hybrid Slots), Up to 2 GB/s PXI Chassis - The PXIe‑1083 features a high-bandwidth, all-hybrid backplane to meet high-performance test and measurement application needs. This PXI chassis features all hybrid connectors, 58 W power and cooling, and an integrated … Thunderbolt 3 MXI-Express controller.
-
Product
DC toDC Converters
-
Low Cost Single Dual and Triple outputs Isolated Outputs Low Ripple, Regulated Outputs Standard packages and pin outs Custom Designs availableNew Miniature V3 Series features HighVoltage Isolation, SIP and DIP packages
-
Product
Programmable DC-DC Converter
VDD Series
-
VDD series is a high power and variable output DC-DC converter which can be operated on DC. Because the DC operation, VDD is most suitable for many applications. For example, it is the best choice for R&D of next-generation energy systems and anti-disaster measure systems, such as Smart house in which electricity is supplied as DC mutually between home rechargeable batteries and EVs, and Voltage adjustment when driving DC electronic equipment by emergency large rechargeable batteries.
-
Product
Phase Noise Measurement Up To 125 GHz
S930321B
-
S930321B enables phase noise measurements using a PNA or PNA-X vector network analyzer. Simplify your measurement workflow by measuring phase noise on the same connection as your network analysis measurement of 2-port active devices up to 125 GHz, without needing to connect a spectrum analyzer or harmonic mixer.
-
Product
DC to LVDT and DC to RVDT Converters
-
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices. They provide a very precise linear AC voltage output proportionate to the magnitude of the input data, in or out of phase respective of the AC reference input as determined by the MSB of the input word (offset binary format).
-
Product
Unidirectional Single-Phase & Three-Phase Analog Converters
-
We produce and market AC/DC analog converters to control DC motors. The 3DBS series is under START POWER design and implementation. This product can be used either as motor control or power supply, indifferently, and is available in the standard series from 40A to 500A.
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
PXIe-1084, 18-Slot (17 Hybrid Slots), Up to 4 GB/s PXI Chassis
784058-01
Chassis
PXIe, 18-Slot (17 Hybrid Slots), Up to 4 GB/s PXI Chassis—The PXIe-1084 features an all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
Product
Protocol Converter Gateway
-
Four-Faith Smart Power Technology Co.,Ltd.
Four-Faith protocol converter gateway is an IoT distributed processing unit designed for the wireless remote and large data transmission. Our Interface protocol converter supports IEC101, IEC104, Modbus, DNP3.0, etc. The protocol converter provides the powerful processing ability of data from Ethernet, Standard RS485, Standard RS232, WIFI or other different communication interfaces for different SCADA platforms, Power protection devices, Intelligent equipment, Different management systems etc. The main function of the Protocol Converter is to process UL and DL data, complete different protocols' forwarding, and achieve transparent transmission of application software communication between different systems and protocols.
-
Product
Testing Hardtop Convertible
-
Magtrol designed this Custom Motor Test System for the testing of motors used in hydraulic systems in hardtop convertible roof drives.
-
Product
DC/DC Converters
-
The DC/DC Converters are available in standard or customized chassis suitable for panel or rack mount. All models feature front panel controls and indicators and are fully convection cooled. Input and Output terminal blocks can be mounted on either front or rear panels.
-
Product
Real Time MM-Wave Frequency Analyzers up to 180 GHz
-
When millimeter-wave applications came into many domains of human activity, a need for precise measurements of signal frequency spectrum has become critical. This need is quite understandable when, for example, it concerns to exploring extraterrestrial radio-sources or micro/mm-wave background emission in radio-astronomy, or measuring chemical composition of the atmosphere through the molecular emission of different its components, plasma diagnostics or many military applications.
-
-
Product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
-
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
Product
Real-Time Analysis up to 255 MHz, Basic Detection, Multi-touch
N9041B-RT1
Signal Analyzer
See, capture, and understand elusive signals as short as 17.17 s with 100% POI and a complete set of advanced triggers, up to 110 GHz View signal dynamics with integrated real-time displays Maximize your investment by adding RTSA at a fraction of the cost of a dedicated solution Easily integrate the 89600 VSA software and thoroughly analyze complex signals Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PCI Dual Channel Multi-Band Down Converter
LS-27-D
-
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
Product
SMPTE Studio Camera Hybrid Fiber Converters & Power Supplies
SMPTE-HUT Series
-
We work in an industry of hybrid workflows and solutions, but sometimes we need authentic innovation that changes how we work. MultiDyne’s next-generation SMPTE-HUT Series is the definition of a pure solution that elevates the live production workflow. SMPTE-HUT universal camera transceivers free SMPTE-based camera chains from the limitations of hybrid copper and fiber cabling, and removes interferences associated with copper connectivity. Camera operators instead have a plug-and-play system that requires only two stands of single-mode fiber - reducing costs, weight, and set-up times – while ensuring the best possible signal integrity. With options to multiplex camera signals, boost the optical range of cameras and regenerate optical power over fiber, SMPTE-HUT is a purist’s solution for remote broadcasting, sports production and other long-distance SMPTE studio camera applications.
-
Product
PXIe-1090, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis
787040-01
Chassis
PXIe, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis - The PXIe‑1090 features a high-bandwidth backplane to meet high-performance test and measurement application needs. This PXI chassis features one hybrid connector, 58 W power and cooling, and an integrated. Thunderbolt 3 MXI-Express controller. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
Product
Chassis - up to Eight 16x1 Solid State 75 Ohm Cable TV Modules or May Be Used to Control a Great Number of 8x1, 4x1, 2x1, or 2x2 Modules
CXAR/256-MF
Chassis
This Chassis is intended to control up to eight 16x1 solid state 75 ohm cable TV modules, or may be used to control a great number of 8x1, 4x1, 2x1 or 2x2 modules. It is often used to control a large variety of custom configurations which may be located in separate chassis.
-
Product
Wideband Digital Down Converter
-
A Digital Down Converter performs channel access functions in digital receivers. It is used for extracting a channel (frequency band) of interest in a wideband signal. Abaco Systems' wideband DDC core employs a quad DDC architecture to achieve ultra high performances. The core accepts up to 16-bit complex data and can process 1GSPS continuously. With a fully programmable architecture at all stages of the processing, this core combines flexibility and speed and can be used in combination with our dual-channel 1GSPS ADC module.
