Serial Peripheral Interface
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, SMBus
-
Product
Interface
RAR-PCIE
Interface
Available in a range of configurations to match your needs, RAR-PCIE provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols.
-
Product
Interface
3508 MMS ECM
Interface
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
PXIe-6591, 12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument
783638-01
Serial Interface
12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument—The PXIe‑6591 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex‑7 FPGA to implement various high-speed serial protocols, and it is programmable with the LabVIEW FPGA Module for maximum application-specific customization and reuse. The PXIe‑6591 takes advantage of FPGA multigigabit transceivers and up to eight TX and RX lanes. In addition to high-speed serial lanes, the PXIe‑6591 features digital I/O signals that support multiple logic families with per line, per cycle direction control.
-
Product
I²C/SPI Interface Device
Interface
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
10-Pin RJ50 Male to 9-Pin D-SUB Male Serial Cable
182845-03
Serial Cable
S8 Serial Cable, 10Pos Modular Plug to DB-9, 3 m (non isolated)
-
Product
Interface
RPCC-D1553
Interface
This dual channel card is RoHS-compliant and is a direct drop-in replacement for the PCC-D1553 card which it replaces. The RPCC-D1553 comes with all necessary cables for operation. Cables designed for the PCC-1553 card will not work with the RPCC-D1553 card. The RPCC-D1553 provides 1 or 2 channels integrated with powerful API software providing instant access to all MIL-STD-1553 databus functionality and data.
-
Product
PXI-8432/ 4-Port, Isolated, RS232 PXI Serial Interface Module
779538-01
Serial Interface
4-Port, Isolated, RS232 PXI Serial Interface Module - The PXI‑8432/4 is a high-performance interface for high-speed, port‑to‑port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Application Programming Interface Software
AltaAPI
Interface
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
-
Product
High Performance PCI-GPIB Interface Card
82350C
Interface
Support fast transfer speeds for high data throughput and easily attach to low-profile PCs.
-
Product
Rugged Aircraft Interface Devices
AB2-AID
Interface
The AB2-AID is ready to go with high-performance avionics I/O combined with valuable built-in features such as a 9-port Ethernet switch, Ethernet to serial bridge, and 8GB flash memory. All in a compact, rugged package for easier integration and longer life.
-
Product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
Serial Interface
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXI LIN Interface Module
Interface
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Interface
RXMC1553
Interface
Abaco Systems’ RXMC-1553 is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a XMC.0 Mezzanine Card. With one or two dual-redundant channels, the RXMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
PCI Bus Interface
PCI-6713-4IP
Interface
PCI Bus Interface 3.3 / 5 Volt via PLX 9056 33/66MHz High Performance Floating-Point DSP Up to 300MHz system clock. Up to 32Mbytes of SDRAM 4.0 Mbit flash memory for bootstrap program.
-
Product
PXIe-8510, 6-Port PXI Vehicle Multiprotocol Interface Module
784122-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows
778032-01
Interface
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
Low-Profile High-Performance IEEE488 GPIB Interface for PCI Bus
LPCI-3488A
Interface
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
Product
Interface
RCNIC-A2PAX
Interface
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
Interface
RCEI-830A
Interface
Designed for embedded, laboratory and simulator applications, the RCEI-830A supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
Product
Interface Panel for SLSC
THROUGHPOINT™
Interface
Bloomy's ThroughPoint™ Interface Panel provides a simple, yet highly-flexible connection between the unit under test and resources in a National Instruments Switch/Load/Signal Conditioning (SLSC)-based test system.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
Interface
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
9-Pin Female DB-9 to 9-Pin Male DB-9 GPIB Serial Cable
183045-02
Serial Cable
RS232 Straight-Through Cable, DB-9 Female to DB-9 Male, 2m
-
Product
Interface
RAR-XMC
Interface
Designed for embedded, laboratory and simulator applications, the RAR-XMC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
Product
9-Pin DB-9 Female to 9-Pin DB-9 Female Serial Cable
183283-01
Serial Cable
RS485 Null-Modem Cable, DB-9 Female to DB-9 Female, 1m
-
Product
Compact-RIO Optical Interface Module
cRIO OPIF 20MBit/s
Interface
Fibre optical interface module for Compact-RIO with the following features:Fibre connection: SC connectorWavelength 820nmData rate: 020MBit/s2 Transmitters2 ReceiversExample SW in LabVIEWField of application of this module:Data communication via fibreOptical isolated data acquisition
-
Product
68-Pin VHDCI Male to 8-Port 9-Pin D-SUB Male, Serial Cable
197546-01
Serial Cable
68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
-
Product
PXIe-6593, FlexRIO High-speed Serial Module (16 Gbps), KU060
785977-01
Serial Interface
PXIe, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument - The PXIe‑6593 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6593 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB GPIB (IEEE-488) Interface
GPIB-USB-HS+
Interface
This compact USB - GPIB interface offers full function, IEEE 488.2 interface support via any computer with a USB port. The interface can control up to 14 GPIB instruments. The small size and light weight of this interface makes it ideal for portable applications using a laptop computer or for other applications in which the computer has no available internal I/O slots. The interface works with any Windows OS.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
