Serial Peripheral Interface
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, SMBus
-
Product
PCI Bus Interface
PCI-6713-4IP
-
PCI Bus Interface 3.3 / 5 Volt via PLX 9056 33/66MHz High Performance Floating-Point DSP Up to 300MHz system clock. Up to 32Mbytes of SDRAM 4.0 Mbit flash memory for bootstrap program.
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
-
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe to PXIe Remote Control Interface Kit with Daisy-chain Facility
43-921-001-KIT
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
-
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
-
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
4 or 8 ARINC Channels in In-Line USB SuperSpeed Cable
NLINE-UA429
-
NLINE-UA429™ is an innovative product of ARINC operations for USB connections, ideal for in-field applications or point-point lab usage.
-
Product
4 or 8 Channels In-Line Real-Time ARINC-Ethernet Converter
NLINE-EA429
-
NLINE-EA429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). NLINE-EA429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
Product
Mini PCI Express
MPCIE-A429
-
Alta Data Technologies’ MPCIE-A429 Mini PCI Express F1 interface module offers a variety of ARINC-429/575/717 channel configurations with software selectable RX/TX channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 transceiver compatible signal.
-
Product
ARINC 429 Interface
RCEI-715A
-
The RCEI-715A is an intelligent, high-density, Type II PC Card (PCMCIA) interface that provides up to 12 fully independent ARINC 429/575 channels, along with up to 4 bi-directional avionics-level I/O discretes.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows
778032-01
-
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
20 GHz Differential Probe with ProLink Interface
DH20-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
PCIe-8244, 4-Port, USB3 Vision Frame Grabber Device
782890-01
-
The PCIe‑8244 is a USB 3.0 interface device designed for use with USB3 Vision cameras. USB 3.0 is ideal for high-data-rate machine vision applications. USB3 Vision cameras also offer plug‑and‑play functionality and ease of use through a standardized catalog of functions.
-
Product
Multi-channel Interface Module
PC104E-MA4
-
Alta Data Technologies’ PC104E-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC PCI/104-Express interface card supported by the latest software technologies. The PC104E-MA4 card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Wide Band Filters (multi-octave)
ERF-5W™ Series (Single & Dual)
-
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
Product
8-Ports Gigabit Ethernet RCV Interface (R)
YAV90058
-
8x RJ45 LAN connectors to VPC RCV 192 pins module.
-
Product
Interface
RCNIC-A2PAU4
-
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
Product
USB Interface for 1-2 MIL-STD-1553 Channels
NLINE-U1553
-
The NLINE-U1553 implements the latest USB 3 SuperSpeed technology for 1-2 dual redundant, independent 1553 channels. Full function capability for Bus Controller (BC), multi-RT (mRT), and Bus Monitor (BM). Also, o-scope signal capture on the first channel to troubleshoot bus signals. All built-in a small, rugged cable assembly that allows the customer to easily connect with standard 1553 jack connectors, or make their own custom cable with a Lemo break-away standard. USB 2 backward compatible (but not recommended – USB 3 offers superior throughput performance).
-
Product
Thunderbolt Interface
NLINE-T1553
-
Supports Full Real-Time Control the Same as a PCI Express Card in a Server! Much Better than a non-real-time USB.Full Hardware Interrupt Handler Support! AltaAPI SDK Provides Easy Integration – Use the exact same code as other Alta PCIe devices! Windows 10 Support Only
-
Product
PXIe-8245, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
787313-01
-
The PXIe-8245 supports Ethernet-based communication between PXI hardware and external instruments and devices. This PXI Ethernet Interface Module includes four RJ45 10/100/1000BASE-T Ethernet interface ports in a single-slot PXI Express module.
-
Product
High Performance PCIe-GPIB Interface Card
82351B
-
Convert your PCI computer directly into an intrumentation control; install easily with plug-and-play configuration.
-
Product
Interface
RPCIE-1553
-
Abaco Systems RPCIE-1553 is the latest generation of performance and flexibility for MIL-STD-1553 A/B Notice II on a native PCI Express module. Available in -40°C to +70°C temperature with one, two or four dual-redundant channels, the RPCIE-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-02
-
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
Product
Intelligent ARINC Interface Module
M4K717
-
The M4K717 is an intelligent ARINC 717 interface module for the multiprotocol Excalibur 4000 family of carrier boards.The module supports two ARINC 717 receive channels and two transmit channels.In transmit mode, the module sends the four subframes from a pre-defined buffer in dual-port RAM.In receive mode, the module stores all subframes with status and Time Tag information appended to each subframe.The M4K717 comes complete with C-driver software library including the source code.
-
Product
PXI-8431/2 , 2-Port, RS485/RS422 PXI Serial Interface Module
778984-01
-
2-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
RF Switching Interface Units (RFIU)
-
LXI, GPIB, and USB RF Interface Units (RFIU) available off-the-shelf or customized for you.
-
Product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
-
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Fixture Interface Module 2 Test Matrices
OTP2 module no.193
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
-
Product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
-
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
