Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
IK Level Tester
IK07-10
-
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
Product
Boundary Scan Compliance Tester
QT900
-
Qmax Test Technologies Pvt. Ltd.
QT900 Qscan Test system is designed to provide test solution for both Boundary Scan compliance devices and Non Boundary Scan devices. The System provided with Digital IO’s capable of driving and receiving via JTAG IEEE 1149 standard interface and synchronous to JTAG pins. Both Digital and JTAG test are carried out synchronously. Use of virtual test pin and Edge connector eliminates the need of expensive test fixture strategy.
-
Product
Analog Multiplexer Board
104-AIM-32 PC/104
-
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
Product
EYE Super Xenon Tester
-
Xenon Tester is the standard climatic wear testing device under domestic and international standards such as ISO, JIS, and ASTM as its light source achieves spectral energy distribution that approximates sunlight which has high correlation to natural outdoor exposure.
-
Product
Smart Network Tester
LinkRunner® G2
-
Validate up to 90W Power over Ethernet (PoE) PSE in one AutoTest – useful during IoT, VoIP, and Wi-Fi deployment. Install and run preferred Android-based apps for speed tests, device configuration, and workflow management with smartphone-like features.
-
Product
Digital Input Board
VME-1128
-
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
DMX Tester
DMXter4 RDM
-
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
Product
Burn-In Boards
-
Manufacture of burn-in boards since 1976. Established for more than 40 years in the market, Trio-Tech is recognized and is an approved global supplier to all major semiconductor companies. Trio-Tech has the capability to design and manufacture boards for all system types, with solutions available for many test conditions, Including HTOL, PTC, HAST and 85/85.
-
Product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
-
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Crease And Stiffness Tester
DRK153
-
Shandong Drick Instruments Co., Ltd.
Whether this is by hand or by mechanical means. The crease recovery (spring back) can result in forces, which distort the erected carton or cause stresses to be applied to closures, which reducetheir effectiveness. With the Crease and Stiffness Tester, the Crease recovery is determined by the decrease in resistance offered by creased board after it is folded 90° at the crease measuring the recovery force after 15 seconds. Board Stiffness is determined by bending a 50mm length of board through a 15° angle.
-
Product
Current Measurement Board
MS 1814
-
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
Product
Socket Outlet Tester
-
Using the new Testavit Schuki 1 LCD and 3 LCD, specialists easily check to see if sockets, cable drums or connecting cables are correctly connected in 230 V installations. Due to three LEDs, the connection status can be quickly and clearly determined. In addition, through the finger contact, it can be tested to see whether an impermissible, high contact voltage is applied at the protective earth connection. In addition, using the Testavit Schuki 1 LCD, a 30 mA FI circuit breaker (RCD) can be triggered via a pushbutton.
-
Product
Vacuum Tester
QCT-2A
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to vacuum cleaner type motor. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
Product
Demonstration Board
SAMPULSE20x2
-
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
Product
De-Energized Tester
MOTOR GENIE
-
The MOTOR GENIE® can see more than a megohmmeter, resistance tester, or RCL tester, making it the perfect tool for troubleshooting, startup, and quality control of low voltage AC induction motors.
-
Product
ISA Isolated Digital I/O Boards
ISO-P64
-
The ISO-P64 has 64-channel isolated digital input board, arranged into four isolated banks. Each input channel use a photo-coupler input which allows either internal power supply or external power selected by jumper. Isolated input channels 0~15 are designed into group A, channels 16~31 are designed into group B, Isolated input channels 32~47 are designed into group A, channels 48~63 are designed into group B. The power supply of the input port may use the external power or the power from the PC side using DC to DC converter. The board interface to field logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The ISO-P64 has one 37-pin D-sub connector and one 40-pin header. The 40-pin to D-sub 37 flat cable is used to fix with the case. The user can connect the digital signal through the second D-sub connector. Each D-sub connector contains 16 inputs channel and 16 output channel.
-
Product
Radiation Dose Testers
-
Handheld Radiation Dose Tester with high sensitive GM counter sensor, combined Beta(β ), Gamma(γ), and X-ray radiation detection. It is widely used in home decoration, radiation processing enterprise, health and epidemic prevention, radiation therapy, import and export inspection, building materials, petrochemical, geological survey, scrap steel, industrial nondestructive testing and other environments existing ionizing radiation, personal radiation dose supervision and protection occasions.
-
Product
Digital Free Chlorine Tester
MW10
-
The Milwaukee MW10 Free Chlorine Photometer lets you go digital with your testing. No more hit and miss testing with strips. Great for agriculture, aquariums, aquaculture & coral, labs, water treatment, classroom and more. This meter is also ideal for educators that want their students to learn the basics of water quality analysis to apply in the real world.
-
Product
Static Tester
DRK151
-
Shandong Drick Instruments Co., Ltd.
The tester is applicable in testing the surface potential and the properties of anti-static products .This tester applies to test electrostatic voltage of charged object such as conductor, insulator, and the human body.
-
Product
Field Sync Tester
Sentinel
-
All-in-one TesterPTP, NTP, SyncE and TDMMulti-port, simultaneous measurementsEmbedded GPS Rx and RubidiumHigh performance. Optional battery to maintain Rb in holdover during transit
-
Product
Earth Resistance Tester
M71
-
M71 has been developed to measure earth resistance with 2 wires and 3 wires by voltammetric method in compliance with standard IEC/EN61557-1.
-
Product
Breakout Boards
-
Breakout your Raspberry Pis and Arduinos with this broad selection of versatile breakout boards! Engineered to help you realize your robotics, GPS and altitude sensing projects as well as servo and touch screen interfacing, you''ll find many uses for these high-quality boards, most of which are manufactured in house at Adafruit!
-
-
Product
Pulse Generation Measurement Board
MS 1806
-
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Lithium Battery Inspection Tester
C19
-
Fuzhou Fuguang Electronics Co., Ltd.
C19 series is a portable tester which can quickly inspect battery pack of two-wheel vehicles. It can realize quick inspection and selection of SOH data of battery pack and discharge-charge maintenance. Data can be transferred to the mobile phone APP through Bluetooth forming a statistics report and faulty cell warnings so that further maintenance solutions can be developed in time.
-
Product
GFCI Socket Tester
ST120
-
The Fluke ST120 GFCI Socket Tester checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120 will give you confidence on your next job.
-
Product
Oxygen Permeability Testers
-
Oxygen permeability is the ability of a barrier material to oxygen to permeate through it in a specific time. Oxygen permeability may vary with temperature, humidity, pressure and specimen thickness.
-
Product
KYZ Indicator and Tester
1031-C3, 1031-C6
-
More than just an indicator, TESCO’s KYZ Indicator and Tester Cat. 1031-C3 (3-wire) and 1031-C6 (6-wire) can also be used to perform accuracy testing of KYZ pulses on all TESCO Next Generation Test Equipment. TESCO’s KYZ Indicator and Testers can be used as a pulse input using the same pickup connection on the front panel of all TESCO Next Generation Test Equipment.
-
Product
Contunuity Tester With Audio Warning
CT-01
-
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
Product
110kV/220kV Substation Series Testers
JYH-C
-
The JYH-C CT & PT Analyzer is a multifunctional device for testing current and potential transformers, covering excitation, ratio, polarity, resistance, and more. It meets IEC standards and features L
