Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
Non-Contact Voltage Tester
1LAC II
-
The Fluke 1LAC II Non-Contact Voltage Tester is easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
Product
EMC Testers
-
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
Product
Filter Testers
-
All filter test equipment from TSI, used for testing efficiencies of filter media and a variety of air filters, including high and very high-efficiency filters, respiratory filters, cartridges, and protective garments, is known for its simple and reliable operation.
-
Product
LAN (2ch) Expansion Board (supporting EtherCAT)
OP-SB89E
-
OP-SB89G is an expansion board for Ethernet LAN which is to be inserted into a slot of portable communication analyzer (LE-8200A/LE-8200). It has 4 LAN measurement ports and you can sniff 2 Ethernet lines at the same time by tap connection to capture packets on the 2 lines. It also can monitor input/output of a EtherCAT slave and measure the time delay cased by the slave.
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
Insulation and Continuity Tester
MIT2500
-
The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.
-
Product
Conductivity Tester
EC
-
Monitor conductivity levels quickly and easily with Series EC Conductivity Testers. These pocket-sized testers are ideal for conductivity measurement in the lab, industrial plant or out in the field. Series EC measures conductivity from 0 to 1990 microhms (S) or 0 to 19.90 milliohms (mS).
-
Product
FMC Loopback Test Board
-
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
Product
LATCH UP Tester
-
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
Product
AMIDA IGBT Tester
600
-
KVI Source: 1 Channel 4Q V/I Source; ±1000V, ±10mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% accurate reading of Range
-
Product
High Voltage Insulation Tester
505
-
Simpson's Model 505 High Voltage Insulation Tester is capable of measuring insulation resistances from 10 kilohms to 1 teraohm with eight selectable test voltages up to 5000 V. As a safety feature, the insulation tester acts as an AC/DC voltmeter to measure the absence of voltage in networks up to 2000 V.
-
Product
Earth Ground Testers
-
TES Electrical Electronic Corp.
Capable of measuring earth voltage. Data hold function. Auto power off function. The timer operates automatically about 10 minutes with the "test button switch are pressed to keep the tester power on.
-
Product
Adhesive Tack Testers
-
Adhesion test is to measure the initial tack and holding power of adhesive tapes and labels. Tack or holding power test is very important in packaging industry and adhesive industry.
-
Product
DIGITAL EARTH TESTER
MTD-20KWe
-
The MTD-20KWe digital earth tester allows for the measurement of Earth Resistances and Soil Specific Resistivity, and also the spurious voltages caused by parasitic voltages present in the soil.
-
Product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
-
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
Product
Insulation Oil Tester
KVJS-7000
-
KV Hipot Power Test Equipment Co.,Ltd
Insulation oil dielectric loss and resistivity tester is mainly used to test dielectric loss factor and resistivity of insulation oil and liquid insulation medium.
-
Product
Solderability Tester
ZHX-35
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
Product
Carbon Monoxide Detector Tester
Solo C3
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
BCI Tester
-
Test scenario creation function of BCI test.・Test scenario auto-run feature.・Test results file generated automatically. (CSV file: can be customized)・CAN / LIN communication function, data logging. (FlexRey available)・Power I/O, ECU I/O control functions, data logging.・Anomaly detection function display.・Noise detection function.
-
Product
Configurable 6U CPCI Multifunction I/O Boards
-
Optimized to deliver unusually high-function density, high resolution / accuracy and low power consumption for rugged defense, commercial aerospace, and industrial applications, NAI’s intelligent 6U CompactPCI cards can often operate as standalone systems, eliminating the need for a Single Board Computer (SBC), operating system and associated software royalty costs.
-
Product
Whole Sole Flexing Tester
SG-P03E
-
Use a cutting tool to pierce the specimen between the cleats at three points along the line of maximum bending stress. By the specified speed and times of 90°bending action to inspect the cuts’ growth with a measuring.
-
Product
Digital Insulation Testers
-
Cut unscheduled downtime and reduce shock hazards by testing wires, cables, transformers or entire electrical systems.
-
Product
Transformer Bench Tester
KVBT
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test System is applied for ex-work and maintenance detecting on various transformers.
-
Product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
-
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
PC104 MIL1553A & MIL1553B Board
MS 1701
-
*Bus Interface - Standard ISA Bus (PC104 Interface)*One Dual Redundant MIL-STD-1553 Channels, Enhanced Mini-ACE BC/RT/MT Architecture*A periodic message insertion, Real-time bus playback with RT edit mode*Highly Autonomous Bus Controller Architecture, Message Scheduling*Bulk Data Transfers, Data Block Double Buffering*Asynchronous Messages, Retries and Bus Switching*Transformer or Direct Coupled 1553B Channels
-
Product
Battery Projectile / Burning Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery projectile / burning tester is suitable for testing the flame resistance and flammability of various consumer batteries, such as mobile phones and notebook computers.
-
Product
COM Express Boards
-
COM Express is a highly integrated Computer On Module. It can be considered as a component (integrated circuit) in more complex designs.
-
Product
Phase Testers
-
Measurement on the voltage detection terminal and covered wireSafely used even for high-voltage bare wiresConsisting of the transmission and reception parts as well as the optical fiber wire connection those two parts
-
Product
13MP Camera Board For I.MX8
E-CAM130_iMX8
-
e-CAM130_iMX8 is a 13MP 4-lane MIPI CSI-2 autofocus color camera board for iMX8 family of processors. The e-CAM130_iMX8 camera board is interfaced directly to the CSI-2 MIPI interface on the Variscite's DART-MX8M/DART-MX8M-MINI Evaluation kit (VAR-DT8McustomBoard). The iHDR (interlaced High Dynamic Range) support helps to capture good quality images in both high and low illumination. e-CAM130_iMX8 also comes with a high-performance Image Signal Processor (ISP) that performs all the Auto functions (autofocus, auto white balance, auto exposure control). Customer who wants to integrate this camera into their end product can directly purchase e-CAM130_MI1335_MOD camera module.
-
Product
IK Level Tester
IK07-10
-
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
