Power Test Systems
-
Product
Capacitance & Tan-Delta Test System
TD-1
-
By measuring the electrical properties such as capacitance and Tan-Delta regularly on periodical basis, it is possible to ensure the operational unexpected breakdown. Dissipation factor (Tan Delta) is one of the most powerful off-line nondestructive diagnostic tool to monitor the condition of solid insulation of various high voltage equipment.
-
Product
Power Electronics Test
-
Aiming at the problem of PI, Shengbo Technology carefully studied the root cause of the problem. Through the loop analysis and noise analysis of power supply and automatic control, it provided targeted solutions for frequency response analyzer and power supply rejection ratio (PSRR) analysis . In addition, we also have a professional technical application support team in the field of power electronics testing. We can customize and develop the corresponding system software for customers so that it can be applied to PC / Servo / Telecom power supplies, adapters and chargers, and backlights. Inverter, LED drivers, ballasts for energy-saving lamps (Ballast), and even UPS, PV Inverter, electric vehicle chargers, AC and DC motors, etc.
-
Product
Motion Simulator For Test Systems
Metis
-
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
Product
LT-300A Aging-Life Test System For LED Luminaires
-
Hangzhou Everfine Photo-E-Info Co., LTD
LT-300A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
Product
Oil Test System
-
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
Product
Power Supply Rack For Climatic Cycling Test
-
One essential part of the module quality testing according to IEC 61215 is the thermal cycling test (MQT 11) and humidity freeze test (MQT 12). Besides the environment simulation in the climate chamber, it is necessary to energize the PV modules during specific parts of the test.
-
Product
Mezzanine System
5089
System
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
Product
Handheld RF Power Meter
V3500A
RF Power Meter
The V3500A Handheld RF Power Meter is a compact, handheld instrument that makes accurate RF power measurements in both field and manufacturing applications. With an absolute accuracy as good as 0.21dB, a wide frequency range of 10MHz to 6GHz, and a measurement range of -63dBm to +20dBm, the V3500A is suitable for a wide variety of RF measurement applications. Its built-in power sensor eliminates the need for users to carry both an instrument and a separate sensor module. Truly portable, the V3500A fits easily into your hand or a toolkit. An optional belt loop holster or carrying case with shoulder strap is also available. To optimize flexibility, it is capable of drawing operating power from batteries, an AC-DC converter module, or a computer via USB interface.
-
Product
Electrodynamic Vibration Test Systems
DC-series
-
Depending on the reference PSD or other operating conditions such as the specimen, one part of the controlled response may deviate from the reference PSD
-
Product
Power, Patchcord, ITA, 36", Mini Power, 16 AWG White Teflon, Single Ended
7-244916000-036
Power Patchcord
Power, Patchcord, ITA, 36", Mini Power, 16 AWG White Teflon, Single Ended.
-
Product
Automotive & Industrial Cycle Testing System
CV
-
The CV is Bitrode's economical cycle life test equipment for the network based line of battery laboratory equipment. Designed to work with VisuaLCN Lab Client software, the CV provides standard or fully customized charge, discharge and rest cycles for automotive and industrial batteries. The Model CV is also useful for reserve capacity and charge acceptance testing with recharge.
-
Product
Memory Test System
T5511
-
Offering Multi-functionality and Industry's Top Test Speed of 8Gbps.
-
Product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
-
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
Product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
-
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
Product
Multi-Wafer Test & Burn-in System
FOX-XP
-
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Product
10 MHz to 6 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2061XA
Power Sensor
The Keysight L2061XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz LAN peak power sensor.
-
Product
Power Networks Test
TX6000
-
The TX6000 is a hand held Time Domain Reflectometer with 11 range scales covering the range 0-6000 meters, with a 7 mater first range scale and a 0.5 meter dead zone near and far end faults are clearly displayed on its 128×64 pixel back light Liquid Crystal Display.
-
Product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
-
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
Product
Function Test Systems & Equipment
-
Cincinnati Test Systems (CTS) provides our customers with turnkey systems that include the design, manufacture and support of custom built lean cell and automated functional equipment testing solutions. We are a recognized global leader for providing test solutions integrated with advanced technology, precision instrumentation, information software written by CTS engineers with proven experience, and supported by a team of technical application specialist.
-
Product
Scienlab Battery Test System – Pack Level
SL1700A Series
-
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increase the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 90 and 270 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Discrete Devices High-speed Testing System
-
QT-6000 discrete device high-speed testing machine is suitable for testing small and medium-power diodes, transistors, field effect transistors and other products and wafers. It can expand built-in capacitance testing (DC+CAP), EAS, VC, pA modules, as well as external LCR (ultra high precision capacitance testing), Scanbox, etc. The machine can be used for FT mass production testing or laboratory testing.
-
Product
Memory Test System
T5851/T5851ES
-
The T5851 system is designed to provide a cost-effective test solution for evaluating high-speed protocol NAND flash memories including UFS3.0 universal flash storage and PCIe Gen 4 NVMe solid-state drives (SSD), both of which are expected to be in high demand for the LTE 5G communications market.
-
Product
Automatic Electrical Protective Equipment Test Systems
CBC-50С (CBC-100C)
-
Automatic systems CBC-C-series are designed for high-voltage withstand testing of electrical protective equipment and insulated hand tools. The tests are carried out with AC voltage (CBC-50C: UAC ≤ 50 kVRMS; CBC-100C: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
Product
Lifecycle Test System
Model 933
-
The Model 933A Life Cycle Test System is a low cost, generic test platform used to perform cycling of keypads, keyboards, membranes, switches, or any product requiring fatigue testing.
-
Product
Non-contact Ultrasonic Testing System
-
Yamaha Fine Technologies Co., Ltd.
Contact-free inspection through ultrasonic transmission detecting air bubbles, separation, and foreign materials inside workpieces. With a Yamaha ultrasonic amplifier installed, contact-less inspection in the air is realized. Without damaging or wetting the workpiece, it is possible to inspect the workpiece for packing defects, air bubbles, and even flaw depth.
-
Product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-193
95-193-001
Modular Breakout System
The 95-193-001 Plugin Breakout Module is designed to be fitted to a PXI 40-193 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Accelerated Life Test Systems
-
Test systems for accelerated life testing and product burn-in utilize Intepro’s electronic loads that are ideal where high power bulk loading is required. Characterization applications within Telecommunication and Aerospace sectors benefit from Intepro’s environmental stress screening (ESS)/Burn-in solutions
-
Product
Automotive Electronics Functional Test System
TS-5020
Functional Test
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
Product
Portable High-Voltage VLF Test System
VLF-60
-
The system is designed for VLF (0.1 Hz) withstand testing of cross-linked polyethylene (XLPE) insulated cables.Integrated Tan Delta (tan δ) measurement module allows to evaluate the general condition of cable insulation according to IEEE 400.2-2013 international standard.
-
Product
Complete Power Quality Analysis System
PK4564
-
PK4564 complete Power Quality Analysis System includes PS4550 Power Quality Analyzer with extended memory, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, CAS3 hard-shell carrying case, PSM-A Software, and 1-year deluxe warranty.
