Receivers
Equipment that is the sink or terminator of any signal on a transmission medium. (atis.org)
See Also: ITA
-
product
Standard Optical Interleaver
An innovative technique for expanding the number of channels per fiber involves an optical device, called an optical interleaver. For example, in most DWDM equipment, the standard channel spacing is 100 GHz. But spacing the signal-carrying frequencies every 50 or even 25 GHz can double or even quadruple the number of channels per fiber. This job is accomplished by an optical interleaver. Such a device takes two multiplexed signals with 100-GHz spacing and interleaves them, creating a DWDM signal with channels spaced 50 GHz apart. The process can be repeated, creating even denser composite signals with 25-GHz or 12.5-GHz spacing. The signals at the receiving end are recovered with the same devices used as splitters or optical de-interleavers. Thus, devices and/or networks can be upgraded without requiring that all devices be upgraded, or network bandwidth can be increased.
-
product
Infrared Receiver For Parallax Small Robots
350-00039
Infrared receiver with 38 kHz carrier frequency, for use as a replacement part with the following small robot kits:*BASIC Stamp Boe-Bot*Robot Shield Kit for Arduino*Propeller ActivityBot*cyber:bot for micro:bit
-
product
Power, Patchcord, Receiver, 72", High Power, 2 AWG, Double-Ended
7-221902688-072
Power, Patchcord, Receiver, 72", High Power, 2 AWG, Double-Ended.
-
product
Timing Modules
Quartzlock provides Timing Modules for network timing, reference disciplining to various input references such as 1PPS, GPS receiver and Frequency References.
-
product
Portable Dual Band ADS-B Traffic and Weather Receiver
DYNON DRX
The DRX is Dynon’s new, affordable ADS-B traffic and weather receiver that fits in your pocket and can last all weekend on a single charge. DRX supports connectivity with most mobile aviation apps, including Foreflight and FlyQ, for superior in-flight situational awareness. See the entire traffic picture with dual band ADS-B reception and receive ADS-B in-cockpit weather products such as NEXRAD Radar, METARS, TAFs, and more. DRX also provides WAAS GPS position to your mobile device and has auto-dimming status lights for night flight. And as usual, the DRX carries on the Dynon tradition of bringing affordable, high quality avionics to all pilots. It’s list price is only $395, but pilots may find it at dealers as low as $349.
-
product
Tool, Extraction, Mini Fiber Optic, Receiver And ITA
910112125
Tool, Extraction, Mini Fiber Optic, Receiver and ITA
-
product
Cable Assembly, Receiver, High Frequency, 36", 10 SMA Plugs
540153010212
Cable Assembly, Receiver, High Frequency, 36", 10 SMA Plugs
-
product
Cable Assembly, Receiver, TriPaddle, 20", 64 MOD to TB-4300B, 300V Input
540281010101
Cable Assembly, Receiver, TriPaddle, 20", 64 MOD to TB-4300B
-
product
Cable Assembly, Receiver, 20", QuadraPaddle, 160 Pin Female DIN
540069120140
Cable Assembly, Receiver, 20", QuadraPaddle, 160 Pin Female DIN.
-
product
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, to LC
7-416804512-036
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, to LC.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Power Connectors
540054040101
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Power Connectors.
-
product
Field Strength Meters
FIM-22 And FIM-41
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their hinged covers, on the rugged drawn aluminum cases, contain a loop antenna. Opening the cover to a vertical position connects the antenna terminals to the receiver via maintenance-free gold-plated contacts. An interlock switch prevents inadvertent battery discharge when the cover is closed.
-
product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male VHDCI
540031020240
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male VHDCI.
-
product
Vertical Hinged Mounting Frame, G6, 5U, 2 Positions
310113397
This 2-position G6 Vertical Hinged Mounting Frame is for use with standard racks or PXI chassis. These mounting frames attach to flanges supplied by the chassis manufacturer and allow the receiver to hinge down for wiring access.
-
product
Coax, Contact, Receiver, 20/26 GHz, Flex 402
610102119
Coax contact, Receiver, 20/26 GHz, Flex 402 (Only available in patchcords).Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield-SolderInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.25 for 2 - 18 GHz1.30 for 18 - 26 GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications Flex 402 (Only Available in Patchcords)Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition AInsulation Resistance 2000 MΩ Min.
-
product
Cable Assembly, Receiver, TriPaddle 256, 20", 3 68-Pin Male VHDCI
540307020105
Cable Assembly, Receiver, TriPaddle 256, 20", 3 68-Pin Male VHDCI
-
product
Inductive Motor Control
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
VTAC, Insert Bundle, Receiver/ITA, SIM, Vertical Header and Pass-Thru
610151108
Each kit contains (1) VTAC vertical header insert and (1) VTAC pass-thru insert. VTAC vertical header inserts get press fit into a PCB and by extension of the VTAC pass-thru insert, a VPC receiver connector can be mounted to the PCB. This is especially useful when mounting an i2 MX receiver or 90 Series SIM module to a PCB.
-
product
Burst Mode Bi-Directional Optical Receiver
RFoG1000
Hangzhou Huatai Optic Tech. Co., Ltd.
RFoG1000 series RFoG ONU, adopts Passive Optical distribution Network (PON) to realize bi-directional, interactive RF business. In FTTH network, it serves to transmission layer of RF video, DAVIC, DOCSIS, extending the optical network to home or building without the need of adjacent HFC optical node. Saving lots of RF amplifier, thus, it can improve the quality and stability of network operation.
-
product
Modular Receiver
Venue2
The Venue 2 Receiver is a modular solution that effectively deals with a congested RF spectrum with a variety of options that allows a system configuration to be idealized for a particular installation or application.
-
product
Noise Figure Measurements With Vector Correction
S97029B
The instrument’s standard receivers are used for noise figure measurements with the S97029B. An external preamplifier and filter(s) is required for devices with < 30 dB of excess noise (gain plus noise figure in dB)
-
product
Two-Tone Decoder
Feed scanner or receiver audio directly into computer sound card, or simply place computer microphone close to receiver's speaker.
-
product
Cable Assembly, Receiver, 20", QuadraPaddle, 68 PN ML VHDCI
540317010140
Cable Assembly, Receiver, 20", QuadraPaddle, 68 PN ML VHDCI
-
product
mAEStro Audio Digital to Analog Converter
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
product
V4 Marine Communications System - V4 NAVTEX Test System
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
product
Strain Relief Plate, Receiver, 90 Series
510109116
Strain Relief Plate for Select Receiver ModulesWorks with Receiver Modules: 510104102, 510104120, 510104123, 510104133, 510104134, 510104136, 510104149, 510104206, 510104243, 510104261
-
product
4.4 GHz Spectrum Analyzer
USB-SA44B
The Signal Hound USB-SA44B is a Software Defined Receiver (SDR) optimized as a narrow-band real-time spectrum analyzer. It is compact, simple to use, and an effective troubleshooting tool for general lab use, engineering students, ham radio enthusiasts, and electronics hobbyists.
-
product
IRD
SFT3975C
Hangzhou Softel Optic Co., Ltd.
SFT3975C HD IRD is SOFTEL’s new product which can receive signals from tuners (DVB-C, DVB-T/T2, DVB-S/S2/S2X, ATSC-T, ISDBT optional), ASI and IP. After demodulating, de-scrambling, re-multiplexing and decoding, it gives content out through various video/audio interfaces (HDMI, CVBS, 3G-SDI) or ASI or IP. This IRD is featured with two CAM/CI slots and BISS which supports to descramble encrypted Tuner, ASI or IP signals.
-
product
FOCL Reference Signal Modem
VCH-607
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
