Stimulus
-
Product
Frequency Response Analyser
DP-cPCI-7554
-
DP-cPCI-7554 is a cPCI module capable of analyzing the phase and gain characteristics of a system. The system under test is stimulated by the user defined waveform. The obtained response is correlated with the applied stimulus by the on-board DSP processor to determine the phase difference and the gain.Gain and the face analysis is carried out only at sine waveform.
-
Product
Measurement and Analytics Solutions
-
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
Product
JTAG Boundary-Scan I/O Modules
SCANIO Family
-
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
Product
Advanced Circuit Card Automated Test
ACCAT
-
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
Product
NI-5741, 16-Bit, 1 MS/s, 16-Channel Signal Generator Adapter Module for FlexRIO
782864-01
-
The NI‑5741 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5741 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5741, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Wide FOV Target Projector
-
The Model 13792 is a broadband portable target projector used for characterizing the performance of a wide variety of infrared sensor systems. The system incorporates SBIR standard components to provide accurate and precise stimulus to sensors under test in laboratory, depot and production line environments. Testing can be automated with the use of IRWindows™ test system controller that reduces test times and cost, while improving the consistency and accuracy of test results.
-
Product
Multi-Wafer Test & Burn-in System
FOX-XP
-
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Product
Diagnostic Test System™
-
The original Teseda system for bench-top stimulus, test pattern debug, validation, device failure mode stimulation in-situ with other Failure Analysis lab equipment such as an EMMI, etc.
-
Product
Nodal Impedance Analyser
QT-Hi1
-
Qmax Test Technologies Pvt. Ltd.
QT-Hi1 is an innovative Nodal Impedance Analyzer, which uses the industry’s proven V-I trace techniques of learn and compare of nodal impedances which are represented as VI Curves. It uses innovative Auto Best Curve fit technique an intelligent software alogorithm which enables automatic selection of the best fit value of Voltage, Source Impedance and Frequency of the stimulus waveform. The compact size with re-chargeable battery makes it an ideal companion for on-field applications. The wide 8” touch screen graphical display makes this tool more valuable in test and repair industry at all times.
-
Product
Modular Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, programmable power module system providing DC, AC and electronic load assets all under control of a single controller. ReFlex Power™ (RFP™) provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test.
-
Product
PXI 8/16-Channel Isolated D/A Converter
M9185A
-
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
Product
VXI 12-Channel, 3-Wire LVDT/RVDT Simulation
65DL2
-
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
Product
Signal Generator
-
Tektronix signal generators cover a wide range of applications, from replicating sensor signals to creating RF and the fastest high speed serial data signals. Each versatile signal generator can create a virtually unlimited number of signals - analog or digital, ideal or distorted, standard or custom. From the world's only direct synthesis of high-speed serial data waveforms for simplified receiver testing, to the world's most versatile arbitrary function generator for common stimulus signals, Tektronix has a signal generator to meet your debug challenge.
-
Product
DC Automated Accelerated Reliability Test Station (AARTS)
DC-HTOL
-
The DC Automated Accelerated Reliability Test Station (AARTS) systems are designed to maximize channel density. The first systems developed by Accel-RF (ARF) were intended for RF and DC stimulus to the Device Under Test (DUT). However, there are some applications in which RF stimulus is not required.
-
Product
Motion Simulator For Test Systems
Metis
-
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
Product
Sensors Test Cells
Integrated MEMS
-
The best technical performance, cost optimization, one-shot factory integration.A single unit integrates the modules for the handling, contacting and complete testing of MEMS devices, including the physical stimulus for functional test, and the tri-temp thermal conditioning.
-
Product
Modular Power
RFP Chassis
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
RFP DC Low Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Modulation Distortion Up To And Beyond 125 GHz
S930713B
-
S930713B enables fast and accurate active-device modulation distortion characterization under modulated stimulus conditions up to and beyond 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930713B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Modulation Distortion For E5081A Up To 44 GHz
S960707B
-
The S960707B modulation distortion software application provides nonlinear DUT behavior tests (EVM, NPR, and ACPR) under modulated stimulus conditions.
-
Product
Bus Analyzer / Exerciser
PCF850
-
The PCF850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Modular Power
RFP DC High Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Resolver to Digital and Digital to Resolver Converter
DP-VME-5031
-
DP-VME-5031 is a Resolver to Digital and Digital to Resolver Converter module. This module has four resolver to digital converters as measurement channels and six digital to resolver converters as stimulus channels.
-
Product
OLED Lifetime Test System
58131
-
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
Product
RF Sources
-
Textron Systems’ commercial RF Sources (RFS 340, SSI) provide an unmatched combination of frequency coverage, power range, signal fidelity and switching speed in either a two-slot VXI, 1U LXI®, or VME Synthetic Stimulus Instruments (SSI) format.
-
Product
RF Automated Accelerated Reliability Test Station (AARTS)
RF-HTOL
-
The RF Automated Accelerated Reliability Test Station (AARTS) systems are designed to stress devices with RF, DC, and thermal stimulus. The systems were designed from their inception to include RF stimulus - it was not added as an after-thought. Hence, the software and hardware are fully integrated and provide full-featured support.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
NI-5742, 16-Bit, 1 MS/s, 32-Channel Signal Generator Adapter Module for FlexRIO
782865-01
-
The NI‑5742 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5742 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5742, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
Product
Modular Power
RFP Controller
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
