Stimulus
-
Product
Modulation Distortion Up To 8.5 GHz
S930700B
-
S930700B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 8.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930700B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Modulation Distortion Up To 43.5 GHz
S930704B
-
S930704B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 43.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
PCI and PCI-X Bus Analyzer / Exerciser
PCI850
-
The PCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
Manufacturing Defects Analyzer
406A
-
The 406A is designed to target the highest number of assembly failures for the least amount of capital equipment cost, programming time, and maintenance costs. The precision Stimulus Measurement Unit provides AC/DC analog measurements that are accurate, stable, repeatable, and reliable.
-
Product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
-
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
Product
Arbitrary / Function Generators
-
Today's designs are often complex, demanding a variety of stimulus signals during test. With standard waveforms, arbitrary waveform capability and signal impairment options, a Tektronix Function Generator supports a wide range of application needs with one instrument. Best-in-class Function Generator performance from Tektronix AFGs ensures signals are accurately reproduced.
-
Product
CXA Signal Analyzer, Multi-touch, 9 kHz to 26.5 GHz
N9000B
-
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
Product
High Speed Digital Analog
-
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
Modulation Distortion Up To 53 GHz
S95070B
-
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
Product
Wafer Level Test Handler
Kronos
-
Wafer level test handler for 6/9DOF sensors with real stimulus. Very high UPH capacity and the lowest cost of test (COT). KRONOS is one of the only wafer level test solutions for motion sensors with real stimulus.
-
Product
Arbitrary Waveform Generator
AWG70000B
-
The AWG70000B Series Arbitrary Waveform Generator represents the cutting edge in sample rate, signal fidelity and waveform memory, making it ideal for design, testing and operations of complex components, systems and experiments. With up to sample rate of 50 GS/s and 10-bit vertical resolution, it delivers the industry's best signal stimulus solution for easy generation of ideal, distorted and “real-life” signals.
-
Product
MEMS Inertial Test
-
Cohu´s inertial solutions enable high precise Gyroscope and Accelerometer test with best-in-class cost of test due to high parallelism and package flexibility. All Cohu stimulus modules guarantee high precision and velocity stability as well as high temperature accuracy. With use of our high efficient handler portfolio we can offer the ideal solution with optimized cost of test.
-
Product
Frequency Response Analyzers
-
Frequency Response Analysis (also referred to as Transfer Function Analysis) measures the output spectrum of a system relative to a stimulus, and is used to characterize the dynamics of the system under test. The technique measures the magnitude and phase relationship between output and input waveforms as a function of frequency. The input signals may be from a wide range of sensors including acoustic (microphones/sonar), mechanical (accelerometers/displacement transducers), optical (photodetectors), and electrical (amplifiers).
-
Product
Benchtop Wiring Analyzer
2115
-
The Model 2115's compact size makes it the ideal choice for many benchtop or portable test applications. The small size does not mean you sacrifice any functionality. The 2115 delivers a full 1500 volt isolation and 2 amp continuity test stimulus. With the optional AC breakdown test providing 1000 VAC test stimulus, you will meet all test requirements.
-
Product
Serial Analyzers
-
This product enables passive monitoring, debugging, and target system analysis of all speeds of Serial RapidIO Gen2 and Gen1 from the physical coding-sublayer (PCS), through serial protocol, to full-duplex link protocol exchanges. Stimulus transmitters allow for injection of SRIO packets, control symbols, and 8b/10b characters.
-
Product
Digital Wideband Transceiver Analysis
S94610B
-
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
Product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
-
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
Product
Digital Stimulus Response PXI Card
GX5152 Series
-
The GX5152 Series are high speed, 6U PXI, digital I/O instruments. The GX5152 master controller has 32 I/O channels that supports test rates up to 50 MHz and vector depths up to 128 Mb per pin. The GX5153 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5152. The GX5152 can control up to 15 GX5153 boards using the same timing and sequencer.
-
Product
6U CPCI D/S, S/D, I/O & Comm Board
78CS2
-
NAI’s 78CS2 is a 6U cPCI Multifunction I/O and Communication Board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five independent function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
