Optic Receivers
Convert an optical signal to an electronic signal.
-
Product
Signal, Module, Receiver, CASS, 210 Position, Right Angle PCB Mount
510113124
Receiver Module
Signal, Module, Receiver, CASS, 210 Position, Right Angle PCB Mount.
-
Product
Fiber Optic Terminus
ARINC 801
-
The ARINC 801 fiber optic terminus is the next generation of high density, butt joint interconnect technology. With its standard 1.25 mm ferrule and sleeve, the ARINC 801 terminus is designed for both multimode and single-mode applications. For the pull-proof design, the cable jacket is crimped on an external body and a floating mechanism avoids any loss of performance when pulling on the cable. This feature allows for the use of the connector without a backshell. Standard connector formats include MIL-DTL-38999 type, MIL-DTL-83527 type, ARINC 600 and ARINC 781.
-
-
Product
VLF Receiver
T-Vlf
-
The VLF receiver is specially designed for high productivity surveys, in ground water and mining exploration. No orientation of the operator with respect to the direction of the transmitter is required since three magnetic sensors measure the components of the VLF field. Tilt or horizontality of the sensor unit is neither required since two inclinometers correct for tilted position.
-
Product
CATV & SAT IF Optical Receiver Module
MRS-26D
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Ultra low noise push-pull technology *Band width of 2.7 GHz* 46dB CNR (typ.) for NISC with OMI = 4% at –8dBm optical input power @ 1550nm* 20dBmV RF output level (-5dBm,1550nm,OMI=4%)* Very low intermodulations *Low power consumption *Small package with single-mode fiber pigtail *Integrated optical demultiplexer (WDM filer) for RF overlay applications *Monitor voltage output and output disable input
-
Product
Alert Receiver Software
SafAlert
-
SafAlert is an autonomous alert decoder triggered by any programmable single, dual, or sequential tone signal, such as EAS, NOAA, or 2-tone fire alarm page. User-programmable visual, audible and email alerting
-
Product
Mini Fiber Optic, Contact, Receiver, Polymer Optic Fiber
610113170
Fiber Optic Contact (Receiver)
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113171. (May mate with other ITA contacts, as well.)
-
Product
Optical Monitoring
-
Perform OSNR monitoring, valid channel detection, and center wavelength measurement of signals with arbitrary modulation formats.
-
Product
Optical BGA Inspection
-
Imaging hidden solder joints of BGA, IBGA, FlipChip, CSP, CGA and SMD components
-
Product
Search Receiver
KMF 1
-
Cable fault location with the BAUR KMF 1. The KMF 1 search receiver is used according to the step voltage method. The cable line is scanned with two measurement probes that can be dismantled during transport. The battery-operated device is also suitable for locating multiple consecutive sheath faults.* Battery mode* Zero point compensation* accurate location of cable sheath faults* battery test
-
Product
Optical Power Meter
-
Shenzhen Golight Technology Co.,Ltd
Optical power meter is built-in large-sensitive surface photodetector and high-precision photoelectric detection. Power testing range is up to 65dB. Also It has optional functions of analog output and trigger sync input. It is widely used in various optical signal measurement.
-
Product
Optical Fiber Transceivers
-
Optical Fiber Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP). Fiberinthebox provide a full range of optical transceivers, such as SFP+ (SFP Plus) transceiver, X2 transceiver, XENPAK transceiver, XFP transceiver, SFP (Mini GBIC) transceiver, GBIC transceiver, CWDM/DWDM transceiver, 40G QSFP+ & CFP, 3G-SDI video SFP, WDM Bi-Directional transceiver and PON transceiver.
-
Product
High Dynamic Receivers
ZRX
-
converter series with high dynamic range receivers. Typical applications are antenna measurements (OTA) and signal analysis. The ZRX Receivers are used wherever full S-parameters are not required.
-
Product
Optical Sensors
-
Analog Devices optical sensors are optical sensing front ends that include integrated ultra-low noise amplification and high performance photodiodes. These solutions are used to achieve the highest performance for instrumentation, industrial, or clinical applications; or to optimize a solution to achieve the lowest power dissipation at a given performance level for battery powered and portable applications.
-
Product
Optical Wavelength Meter
-
Optoplex Optical wavelength meter (OWM) uses proprietary thin-film interference filter in conjunction with Fabry-Perot cavity technology combined with a micro-actuator and high-speed electronics. Its working principle is schematically shown below. By comparison with Optical channel monitor / Optical performance monitor, the proprietary wavelength reference unit is introduced to ensure high precision wavelength measurements. Optoplex Optical wavelength meter is the only DWDM wavelength meter capable of measuring wavelengths of multi-lasers in DWDM networks over C-band and L-band wavelength range with a high accuracy better than that the wavelength locker can provide. For example, the device can simultaneously report 80 wavelength values of 80 channels at 50 GHz channel spacing with the wavelength accuracy ± 2 GHz. DPRAM, RS-232, or USB interfaces are available and OWM can be customized to meet specific requirements.
-
Product
Optical Balloon Theodolite
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Robust instrument*Bright scope with wide field occular and fix focus*Magnification 16x (20x optional)*Field of view 55,6m/1000m (optional 27,8m)*Open finder sights*Double vertical circles (reading from both sides of the instrument)*Reading of circles 0,1°*Convenient targeting through friction-controlled by endless wormdrive screws*Accessories upon request like alarm clock, filters, tripod etc.*Long life cycle, full spare part availability*Made in Germany
-
Product
EMI Test Receiver
ESRP
Receiver
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
Product
Optical Power Meter
SAT-7E PON
-
Shaanxi Aitelong Technology Co., Ltd
SAT-7E PON power meter is a special tester to test FTTx/PON passive optical network, it can synchronously measure voice, data and video signal on BPON/EPON/GPON framework. It also can set the power threshold and indicate the pass, alarm and fail of every wavelength.
-
Product
Aerosol Optical Tweezers
-
Bristol Industrial & Research Associates Ltd
Biral Manufacturers Aerosol Optical Tweezing instruments that offer the ability to study individual particles over indefinite periods. Developed in collaboration with the Bristol Aerosol Research Centre at the University of Bristol the instruments are used in research applications such as atmospheric chemistry, pharmaceutical drug development and basic aerosol research.
-
Product
Passive Optical TAPs
SplitLight
-
Designed for networks with high fiber counts, SplitLight is a patented and customizable 1RU solution offering the industry's highest density of Passive Optical Network TAPs, WDMs, and wavelength filters in a 1RU chassis. Using this platform, service providers, data centers, large enterprises, and government agencies can now monitor more fibers, or filter and route more wavelengths, than ever before while saving valuable rack space.
-
Product
Receiver, I2 Micro ICon, 168 Position, Fully Loaded With Twin Female Contacts (610 138 200)
310130101
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is fully loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kit, protective cover, and strain relief are available.
-
-
Product
Receiver, 9025TR, 25 Module, With 20" Platform, For Tabletop
310104436
Receiver
The 9025TR receiver includes a platform with runners that provide a smooth-sliding action, ideal when using large fixtures. It can be adapted to accommodate vacuum or mechanical fixturing. VPC modules can be intermixed to establish flexible custom interfaces which are ideal for functional and system testing applications. The 9025TR uses all standard modules and contacts, and includes a microswitch. Includes rear cover to protect wiring.
-
Product
Optical Profilometers
-
Profilm3D® and Zeta™ optical profilometers provide fast, easy, non-contact solutions for 3D surface topography measurements. Our portfolio of optical profilers supports a variety of measurement techniques, including white light interferometry, True Color imaging and ZDot™ confocal grid structured illumination. KLA Instruments can help guide you to the right optical profiler solution for your unique needs.
-
Product
Reticles, Optical Slits, Optical Apertures
-
With over 30 years of experience in the manufacturing of high precision Reticles, Slits, Apertures, and Pinholes, APPLIED IMAGE has gained a reputation for delivering precise and accurate parts. We have supplied thousands of these parts to be used in Day/Night Sights, Binoculars, Targeting Systems, Telescopes, Tank Sights, Microscopes, and many other Bore-Sight devices.
-
Product
Optical Inspection
-
Typically, in a standard PCB manufacturing facility, there will be a department where people perform inspection of PCBs through a manual processes, such as visual inspection with magnifiers, microscopes, etc...
-
Product
Optical Path Converter
LS512A/LS512B
-
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.
-
Product
Digital Optical Transport
-
The ATX GigaWave digital optical transport portfolio is designed to fortify cable operators with maximum flexibility and cost efficiencies to support a range of applications and business models. The GigaWave Digital Link Extender (DLX) is optimized to support distributed access architectures (DAA), including Remote PHY (R-PHY) and Remote MACPHY (R-MACPHY), as well as Passive Optical Network (PON), Small Cell/5G and enterprise business services. The GigaWave Digital Link Amplifier-HUB (DLA-HUB) is a field-hardened, gain-flattened EDFA platform that enables the elimination of physical hub sites along long-reach optical routes. The GigaWave digital optical transport portfolio also enables MSOs to leverage the advantages of digital optics over analog, including the capability to transport signals over longer distances and provision additional wavelengths per fiber.
-
Product
Fiber Optic Communications
-
Fiber optic converters are installed between the end of fiber optic cables and data loggers to provide a lightning-proof connection.
-
Product
Optical Fiber Identifier
BD-IF400D
-
Shanghai Baudcom Communication Device Co.,Ltd.
BD-IF400DOptical Fiber Identifier is an important tool for optical maintenance, which isused for nondestructive fiber identification project. Meanwhile it also hasVisual Fault Locator module with fault location function. Useingthe macro bending technology on line for nondestructive testing, BD-IF400DOptical Fiber Identifier can measure the signal direction and power and avoidmisoperation resulting in interrupted lines.
