PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
3U 4HP PMC Adapter for cPCI
cPCIBPMC3U32
-
cPCIBPMC3U32 is a 3U 4HP PMC adapter for cPCI. One PMC position is provided with a 32 bit interface for both the PMC and the cPCI backplane. User programmable VIO on the PMC side of the bridge. High capacity mini-planes with filtering for 3.3 and 5V.
-
Product
PCI to PMC Adapter / Carrier
PCIBPMCx2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
Product
cPCI to PMC Adapter / Carrier
cPCIBPMC
-
The cPCIBPMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCIBPMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
Product
32-bit PMC to PCI Adapter
8092
-
This PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
32-bit / 33 MHz PMC to PCI Adapter
4933
-
This PMC to PCI Adapter product from Technobox permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
Optional Fan Assembly
8094F
-
Optional fan assembly for 8093 and 8094 64-bit/66 MHz PMC to PCI Adapters.
-
Product
64-bit PMC to PCI Adapter
4930
-
This passive PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment.
-
Product
cPCI to PMC Adapter / Carrier
cPCI2PMC
-
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
Product
64-Bit PMC to PCI Adapter
4954
-
This 64-bit PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications. PMC suppliers can introduce products to desktop packaging without having to maintain two PCI-based designs ? one for standard PCI and a second for PMC.
-
Product
64-bit PMC To PCI Adapter
8096
-
This 64-bit PMC to PCI Adapter permits delivery of PMC applications in a standard PCI environment. PMC suppliers can introduce products to desktop packaging without having to maintain two PCI-based designs — one for standard PCI and a second for PMC.
-
Product
PMC Module
PMC-DA816
-
The PMC-DA816 is a slave Digital to Analog boardthat is managed by the host processor on the PMCbus. The card contains a state machine that performsmost of the work of outputting data, in order tominimize the impact to the HOST system.The PMC-DA816 is supported by ALPHI Technologyunder Windows NT by a Board Support Packagewhich is supplied with the card. Other documentationsupplied with the card will describe this support in fulldetail.
-
Product
PMC Module
PMC-softDAC
-
2 µS settling time, 0-5v range• Six Programmable OutputRanges per channel• Unipolar: 0V to 5V, 0V to 10V• Bipolar Mode: ±5V, ±10V,±2.5V,–2.5V to 7.5V• 1LSB Max DNL and INL Over theIndustrial Temperature Range• 64k DAC buffers• Power-On Reset to 0V• Flash ram for configuration file• Two stage buffers• Global output buffer w/ internal orexternal triggering
-
Product
PMC Module
PMC-1553-TACEx
-
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
510140125-2
-
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
-
Product
EBIRST 200-pin LFH Coaxial Adapter - 56 SMBs
93-002-202
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Pull-Thru Adapter, Wired, for Pickering 40-161-101
510140177
-
Pull-Thru Adapter, Wired, for Pickering 40-161-101
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002
510140253
-
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002.
-
Product
PXI Pull-Thru Adapter, Double Slot, 6.75"
510109566
-
The PXI Pull-Thru Adapter can house discrete wiring that connects from a VPC i2 MX Receiver module to a PXI card. The Adapter has a removable side plate and thumb tabs for easy removal from the Receiver frame. Accepts all i2 MX Receiver modules.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male
510140158
-
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 36" Cables
510150143
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 36" Cables
-
Product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Female VHDCI Connectors
510150126
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Female VHDCI Connectors
-
Product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
-
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
Product
Pull-Thru Adapter, Wired, TriPaddle, f/ NI PXIe-5423
510140249
-
Pull-Thru Adapter, Wired, TriPaddle, f/ NI PXIe-5423.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 20" Cables
510150142
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 20" Cables
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (m) To WR-12, 60 To 90 GHz
E281DS
-
E281DS In-line 1.0 mm (m) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Pull-Thru Adapter, Wired, TriPaddle/Mini Coax, 90 Series, for PXIe-5172
510140248
-
Pull-Thru Adapter, Wired, TriPaddle/Mini Coax, 90 Series, for PXIe-5172.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2529 with six 36" cables
510150154
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2529 with six 36" cables
-
Product
A-quad-B cable
E1735A-001
-
The A-quad-B cable is a 3-meter cable that connects your machine's A-quad-B encoder output to the E1735A USB axis module's A-quad-B input connector. The cable is supplied with a mating connector for the USB axis module on one end. The other end is un-terminated, allowing you to make the connections you need for use with your machine's encoder.
