PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
NI-6584, 16 Mbit/s, 32-Channel Digital I/O Adapter Module for FlexRIO
781290-03
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
Adapter, 2.4 mm (m) to APC-7, DC to 18 GHz
11902A
Coax Adapter
The Keysight 11902A is a 2.4 mm male to APC-7, metrology grade adapter with dc to 18 GHz operation.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 20" Cables
510150142
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 20" Cables
-
-
Product
PMC Carrier/Adapter/Motherboard
PMC-MC-X4-RIO
-
PMC-MC-X4-RIO adapter, carrier, motherboard provides the ability to install up to 4 (four) PMC modules into a small enclosure. PMC-MC-X4-RIO has two PMC card positions top and bottom to create a compact arrangement with 4 PMC positions. X4 is a complete solution with built in power supplies, thermal protection, voltage monitoring, bus arbitration, clock distribution, fan control and more. Compact chassis available to house PMC-MC-X4-RIO.
-
Product
FMC, XMC & PMC
-
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
Product
Test Adapter
Ramcheck 72 Pro
-
Our latest addition to the RAMCHECK memory tester provides needed support for testing 72-pin SO DIMM modules used in older laptop computers. The RAMCHECK memory tester automatically detects the presence of the RC 72 Pro adapter
-
Product
ARINC 429 PMC Interface Module
PMC-429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
PMC
-
LinkedHope Intelligent Technologies Co.,Ltd.
PMC is the de facto standard for mezzanine cards used in the VME, CompactPCI and VPX ecosystems. PMC offers system designers a reliable form factor with the high-performance of the PCI bus.
-
-
Product
16-Port RS232 Async Serial Communications Adapter PMC
2238
-
The Technobox 16-Port Async Communication adapter provides sixteen 16550-based UARTs using RS232 signaling levels.
-
Product
PMC Interface Module Carrier
PIM-Carrier-6U
-
The PMC Carrier routes the PMC IO from P04/P14 to J3/J5. PIM-Carrier-6U routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis.
-
Product
PMC Interface Card
CPCIC-MA4
Interface Module
The CPCIC3/6-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
Coax Adapter
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 110 GHz
11920B
Coax Adapter
The Keysight 11920B precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms and frequency range from dc to 110 GHz.
-
Product
PMC
-
A PCI Mezzanine Card or PMC is a printed circuit board assembly manufactured to the IEEE P1386.1 standard. This standard combines the electrical characteristics of the PCI bus with the mechanical dimensions of the Common Mezzanine Card or CMC format (IEEE 1386 standard).
-
Product
Emulation Adapters
-
With some of the more advanced 32-bit microcontrollers and SoCs, the full program and data trace capabilities of the device are not made available on production silicon. Instead, semiconductor vendors provide special 'emulation devices'. These typically feature more pins than the production device, thereby providing the interface to the trace interface.
-
Product
Waveguide Adapter
-
RF Lambda’s waveguide adapter product line is used to convert a waveguide interface to a coaxial interface. They come in a variety of frequencies, connector options and materials. They offer low insertion loss and VSWR as well as high power handling.
-
Product
USB I2C Adapter
MS (Master & Slave)
-
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
Product
PMC (ccPMC VITA 20)-to-4X PCI Express (PCI-e/PCIe) Adapter
6768
-
Our conduction-cooled adapter that permits the insertion of a single PMC into a PCI Express (PCIe/PCI-e) slot (4X). The adapter orients the ccPMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket.
-
Product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial III
-
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
8-Port RS232 Async Serial Communications Adapter PMC
2229
-
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS232 signaling levels. Each port provides the full set of data and modem control lines configured for DTE
-
-
Product
Special Adapters
-
There are use cases when the debug tool doesn’t connect to the embedded target through an architecture standardized and widely used connection. Special Adapters are available to connect the iC5700 BlueBox to the embedded target system in such environments.
-
Product
DB9 To Twinax Adapter
DB9TWX67
-
The DB9TWX67 is an adapter for converting the DB9 outputs of ANDOR Design’s MIL-STD-1553 cards to the Twin Axial connector used in MIL-STD-1553. Two adapters are supplied with each dual redundant channel card.
-
Product
Waveguide Adapter
-
Waveguide adapters in a variety of waveguide standards / flange types and coaxial connectors
-
Product
USB to I2C Adapter
Model JI-300
-
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
Product
Adapters & Pin Converters
-
Need to adapt your emulator's JTAG connection? We have a variety of pin converters to help connect your debug probe to your target board's JTAG connection, such as TI, MIPI, ARM, and Cortex.
-
Product
Waveguide To Coaxial Adapter
D25-BWC26NK-260
-
Waveguide To Coaxial Adapter, Frequency2.17~3.3GHz, Power 500W, WR340, Flange FDP26, N Type Female Connector
