Screw Drivers
Combine screwdriver, voltage detector and/or continuity tester into one.
-
Product
Rad Hard GaN Drivers
-
The space market has been driving towards more efficient power management solutions. Part of the drive includes the use of Gallium Nitride Field Effect Transistors (GaN FETs) for power conversion. GaN FETs have higher power conversion efficiency and have more natural immunity to radiation, due to them being wide-bandgap semiconductors. Equally important is the use of the correct driver that will allow reliable operation and maximize the benefits of the GaN FETs. Some of the key driver requirements are: a well-regulated gate drive voltage; high source/sink current capability and a split driver output stage.
-
Product
PCI Digital I/O and Relay Driver Cards
-
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
Product
Eddy Current Probes and Drivers
-
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
Product
PXI Attenuator/Switch Driver Module
M9170A
Attenuator
The Keysight M9170A is a one-slot PXI attenuator switch driver module that provides the flexibility to drive Keysight's expansive portfolio of RF & microwave step attenuators and electromechanical switches. It is a PXI-hybrid compliant module that comes with a full-featured graphical interface soft front panel for easy control and trigger.
-
Product
0 Hz/DC to 14 GHz, Single-Pole, Four-Throw MEMS Switch With Integrated Driver
ADGM1304
-
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
Product
LED Drivers
-
ST offers a large portfolio of energy-efficient DC/DC powered LED driver ICs for general lighting, display LED backlighting, automotive exterior and interior lighting, RGB and monochromatic LED drivers for signage and traffic signals.
-
Product
Advanced Driver Assistance System (ADAS)
-
Cars have come a long way since they first came on the road in the 19th century. The first semiconductor-based noteworthy assistance was GPS-based car navigation systems toward the end of ´80s. Today, in almost every car, ABS (Anti-Lock Braking System) and ESP (Electronic Stability Program) are also contributing toward the driver and car passenger’s safety using high quality electronics. After all, the dreams of automated cars from the ´60s are now becoming true — it is only a matter of a few years.
-
Product
TB-2648, Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block
781131-01
Terminal Block
Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2648 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2648 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
Product
Laser Diode Drivers (LDD)
-
LDD technology has evolved from driving DVD/CD/Blue-ray optical drives to include laser projection in smartphones, automotive head-up displays (HUDs) and pico projectors. Renesas has developed new LDDs for RGB scanning laser projection systems and laser-based pico projectors. Automotive HUDs are benefiting from big innovations in MEMS projection systems and are now central to advanced driver assistance systems (ADAS) and safety. The latest laser scanned-MEMS projection systems can provide higher resolution images and at a lower cost.
-
Product
Module Accessory Kit, Quantity 26, 4-40 x .50" Socket Head Cap Screws Stainless Steel
510109495
Accessory Kit
Used with modules: 510108240.
-
Product
Low-Side FET Drivers
-
Renesas' low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents into highly capacitive loads and are excellent at driving large capacitive loads with minimal delay and switching times.
-
Product
Door Module Drivers
-
ST’s actuator drivers are designed for state-of-the-art automotive door-module applications. Our devices employ a scalable actuator-driving concept, which includes package and software compatibility with the wide variety of door electronics used by the industry.
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
Cable Assembly, 68 Pin Male VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 18"
515109113
Cable Assembly
Cable Assembly, 68 Pin Male VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 18"
-
Product
10 N Screw Flat Grips
-
10 N (2.2 lbf) screw flat grips are primarily used for tensile testing low force, soft materials such as yarn, paper, plastics, and cloth, in film or wire geometry. Grip faces are flat and rubber-coated, and the supplied coupling joints for the 10 N screw flat grips are designed for use on lower-capacity load cells.
-
Product
Heavy Load Ball Screw with Caged Ball Structur
HBN
-
Heavy Load Ball Screw with Caged Ball Structure. Heavy load ball screws with the caged ball structure (HBN model) drastically improve the rated load compared to the conventional products by utilizing the optimum internal structure for use in heavy load condition. In this model, the caged ball structure is adopted between balls to eliminate collisions and mutual frictions of the balls and improve the lubricant maintenance. This modification brings about a longer lifetime under heavy load conditions.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 36"
515109120
Cable Assembly
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 36"
-
Product
Four Channel Clock Driver Card
PI-41401
-
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
Product
Module Accessory Kit, Quantity 26 4-40 x .25" Flat Head Phillips Screws 100 Degree
510109367
Accessory Kit
Used with modules: 510108112.
-
Product
96-Pin Female DIN to 88-Pin Female Screw Terminal, 10 V, PXI Module Mount Terminal Block
781347-01
Terminal Block
NI TB-4330 Terminal Block for PXIe-4330
-
Product
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Slotted Screws
510109306
Accessory Kit
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Slotted Screws
-
-
Product
Piezo Drivers
-
Use Trek high voltage amplifiers to drive piezoelectric elements and piezoelectric (ferroelectric) material poling.
-
Product
Manual Screw Flat Grips
-
Screw flat grips are general-purpose grips used for static tensile testing of a wide range of materials, most commonly, rubbers, plastics, textiles, and paper, and specimens such as plates and wires. Another advantage of these grips is they can be used to test thick specimens, up to 16 mm (0.63 in).
-
Product
TB-2630B , Screw Terminal, Ribbon, PXI Module Multiplexer Terminal Block
781687-01
Terminal Block
The TB-2630B provides the necessary routing to configure the PXI-2630B PXI Multiplexer Switch Module as a single, dual, or quad 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2630B to the front panel I/O connectors of the PXI-2630B. The NI TB-2630B features ribbon cable headers to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
-
Product
LVDS (Low Voltage Differential Signaling) Drivers and Receivers
-
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
Product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
-
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
Product
Current Pulsers and Laser Diode Drivers (Pulsed Current)
-
These instruments generate current pulses whose amplitude is largely independent of the load voltage. This makes them ideal for pulsing device whose voltage may vary with time (for instance, the voltage drop of laser diodes may vary with temperature, or explosive squibs which change impedance during ignition). This voltage independence is a trade-off with speed. If faster rise times are required, consider using pulsed voltage instruments instead.
