Fuel Injection
-
Product
MASTER FUEL PRESSURE TEST SET
FPT5000
-
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
Product
Fuel Cell Hardware
-
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
Product
SparkFun LiPo Fuel Gauge
-
LiPo batteries are a great way to power your projects. They're small, lightweight, and pack a pretty good punch for their size. Unfortunately, even the best batteries eventually run low on power and when they do it's often unexpected (and at the worst time). Don't be caught by surprise next time your board suddenly powers-down! The SparkFun LiPo Fuel Gauge connects your battery to your project and uses a sophisticated algorithm to detect relative state of charge and direct A/D measurement of battery voltage. In other words, it tells your microcontroller how much 'fuel' is left in the tank. The LiPo Fuel Gauge communicates with your project over I2C and an alert pin also tells you when the charge has dropped below a certain percentage.
-
Product
Primary Current Injection Tester
SLQ
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
It's a high voltage generator insutrment for tesitng.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
BASIC FUEL PRESSURE TEST SET
FPT1000
-
Quickly and easily diagnose fuel-related issues on gasoline vehicles equipped with standard or small Schrader test ports as well as other popular applications3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary Gauge features a dual-scale dial with ranges from 0-100psi and 0-7 bar with rugged boot and hook for hands-free reading and durability.
-
Product
PEM Fuel Cell
48 Volt 5kW
-
It is the aim of CellCare Technologies to continually introduce new technology that can provide significant benefits over existing solutions in specific applications. Fuel cellThe latest introduction to the product portfolio is a 5kW PEM (Proton Exchange Membrane) based hydrogen fuel cell, designed to replace 48V standby batteries within remote telecoms sites, satellite base stations, ISP base stations, uplink facilities and weather data collection sites. This technology provides instant power with no hazardous waste, zero emissions, extended autonomy and a guaranteed lifetime with minimal maintenance.
-
Product
Secondary Current Injection Test Trolley
-
SCR ELEKTRONIKS have developed SECONDARY CURRENT INJECTION TEST TROLLEY for Switchgear items, CT manufacturer and where three phase current application is called for. It is low Voltage, 3 phase Current source with control circuitry, digital read out for test current and trip time measurement. We can select different CT ranges for each phase independently and adjust the current as per the required test Current.
-
Product
Measurement Systems For Fuel Cycle, Safeguards And Decontamination & Decommissioning
-
Advancing critical radiation safety. Our technologies safeguard nuclear materials to protect people and the environment.
-
Product
PEM Fuel Cell Test Stations
-
Available with Greenlight''s integrated ''Intelligent Fuel Cell Diagnostics'' capabilities:FCDXTMCE certification including optional 3rd party verificationIndustry-leading software and diagnosticsAutomated reformate gas simulation (blending)5 different gas humidification technologies available, including Greenlight''s optional Rapid Response humidification system24/7 unattended operation with Emerald control and automation softwareIndustry leading cell voltage monitoring accuracyUser-adjustable safety featuresFuel cell stack leak testingOptional integrated environmental chambersOptional high temperature configuration, specifically designed for PBI membrane researchOptional DMFC configurationWorldwide service and support
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Product
Fuel Cell Test Software
-
Exceptional functionality with a user-friendly graphical interface- Enhanced with our proprietary automation language, Emerald Software - Comprehensively manages the full range of FCATS fuel cell test system parameters- Simple user-friendly interface permits even novices to begin testing in minutes
-
Product
High-Precision Fuel Flow Measurement System
-
It enables to keep the temperature fluctuation of the circulation flow path in the system within ±0.2 °C (for 1 minute), which achieves stable fuel flow rate measurement.
-
Product
Primary Current Injection Testing
KAM
-
This substation testing device is designed to grant high current output when needed in substation commissioning activities.
-
Product
Fuel Pressure Testers
-
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
Product
Fuel Cell Test Stations
-
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
-
Product
20Hz Injection Kit Monitoring System
-
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
Product
Bulk Current Injection Probes
-
The Com-Power CLCI-100 and CLCI-400 are precision bulk current injection probes designed for conducted immunity testing. The CLCI-100 covers 10 kHz to 100 MHz, while the CLCI-400 extends up to 400 MHz and complies with MIL-STD-461 and RTCA DO-160. Both models feature split-core ferrites for easy cable insertion and are compatible with calibration fixtures for accurate RF injection and monitoring.
-
Product
Primary & Secondary Current Injection Testing Sets
-
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
Product
Primary Current Injection Set
-
It is widely used in industries for instrument transformer and switchgear testing.
-
Product
Injection Transformer
J2101A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Product
Mixed Injection System Liquid Vaporizers
MI-1000/MV-1000
-
This mixed injection system can rapidly vaporize a wide variety of liquid sources by using the gas-liquid mixture vaporization method. This method allows for the stable vaporization of high boiling point liquids.
-
Product
Universal Primary Injection Test Set for Substation Assets
CPC 100
-
The patented CPC 100 primary injection test system replaces several individual testing devices. This reduces the costs for training and transport, and cuts down testing time.
-
Product
Battery Fuel Gauge
-
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
Product
Secondary Injection Test Set
PTE-100-C
-
The PTE-100-C is a portable Universal test equipment for testing electromechanical, electronic, and digital relays. The equipment can output a variable current up to 250A, a variable AC Voltage up to 250V, a variable DC Voltage up to 350V. Also the unit incorporates a variable stabilized auxiliary DC Voltage supply up to 250V and a fixed AC Voltage output up to 110V, which can be variable with the PTE-FCF option.
-
Product
Fuel Flow Measurement Systems
FQ Series
-
Measuring a vehicle’s fuel flow requires a precise system which can run stationary and transient tests. It must also be able to offer high reproducibility and run cycle measurements under real operational conditions, including WLTP. Our FQ Series of fuel flow measurement systems offers a highly precise method of measuring various fuel types, and covers the full range from small engines (incl. single-cylinder research engines) up to heavy-duty engines with up to 5000 kW.
-
Product
Direct Liquid Injection System
VC Series
-
The VC Series is able to rapidly vaporize pure water or other liquid sources without carrier gas, which enables you to construct a more compact vaporization system.
-
Product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
-
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
Product
Primary Current Injection Test Set
T 3000
-
T 3000 is a primary current injection testing system designed to perform primary tests requested in substations commissioning. It allows to perform different tests and measurements on current transformers, voltage transformers, power transformers, protection relays, energy meters and transducers
-
Product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
-
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
