Conductivity
-
product
Power Supply
Power supplies of various ratings for Air, Naval ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factor designs.Most products qualified to requirements of MIL-STD-461C and MIL-STD-810D or the equivalent JSS 55555 are designed and manufactured. Airborne versions are designed to meet MIL-STD-704D. Specific design constraints are handled with respect to long time storage life and suitability for air cooled or conduction cooled applications. Designs suitable for high power supplies of various ratings for Air, Naval, Ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factors designs.
-
product
Handheld Water Quality Meters
LAQUA PC210
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
product
Wires and Pipe Locator
LKZ-720
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
product
Laboratory Water Testing Meters
Bionic Scientific Technologies
Is an ideal instrument used for performing TDS or Conductivity test procedures.
-
product
Emergency Conditions Testing
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
VPX Extender 3U VITA67.1 Conduction Cooled
1940000519-9001R
3U VPX Extender for conduction cooled boards mounted in conduction cooled chassis VITA 67.1 (VITA 67.1 connectors not included)
-
product
16-Channel ADC Module
FMC116
Sundance Multiprocessor Technology Ltd.
The FMC116 is a sixteen-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides sixteen A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC116 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
-
product
Liquid Thermal Shock Baths
TSB Series
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
product
Seismic Acquistion QC Serivices
Overall data quality / cost monitoring / safety / daily reporting to client. Verif-i provides technical and operational programme assurances for seismic surveys conducted for the company. The lead acquisition QC on-board/on-crew the seismic vessel/block accepts or rejects data on behalf of the company. Our representative will assist the contractor in fulfilling the technical and operational requirements of the seismic programme and report on crew activities.
-
product
PXI 3A Power MUX BRIC, 9-Channel, 16-Pole
40-571-203
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Soldering Test
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
product
PXI High Density MUX BRIC, 96-Chan, 10-Pole
40-570-416
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Miniature Piezoelectric Accelerometers
Structured with highly sensitive piezoceramic sensing elements, miniature Ceramic Shear ICP® Accelerometers have an excellent signal-to-noise ratio, high measurement resolution, and are ideal for conducting low-level vibration measurements. Due to their inherent higher sensitivity, a ceramic ICP® accelerometer can be assembled with a smaller mass than comparable quartz units, resulting in a sensor that is lighter in weight, has a higher frequency response, and has a lower noise floor. To further reduce the mass of the sensors, all ceramic shear accelerometers are housed in either tough, lightweight, laser-welded, hermetically sealed, titanium or aluminum housings. By minimizing the mass of the sensor, mass loading effects are reduced, which maximizes the accuracy of the data obtained.
-
product
Hazardous Location Transmitter
X80 Series
The ECD Hazardous Location Transmitters – Model X80 Series provides the same capabilities and general feature set as the general purpose T80 Universal Transmitter. Various configurations are available as single or dual channel for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity. The Model X80 transmitter digitally communicates with any ECD Model S88 and/or S80 Intelligent Sensor, automatically configuring the transmitter’s menus and display screens to the measured parameter. The X80 is designed with a durable stainless steel enclosure for explosion proof/exd hazardous applications.
-
product
High-voltage Testers
Operational safety and reliability of electrical equipment and cables directly depend on the dielectric strength of the insulation. Portable and mobile high-voltage testers from KharkovenErgoPribor Ltd. are used for acceptance and operational testing of substation equipment and cable lines, as well as for checking the reliability of personal electrical safety equipment. Our testers range is represented by test systems that allow conducting high-voltage tests with DC and AC voltage, testing polymer insulated cables with very low frequency, testing and locating faults in cable sheath, as well as performing the initial burning of insulation on damaged sections of cable lines.
-
product
High Frequency (RF) Testing
C.C.P. Contact Probes Co., LTD.
CCP designs high frequency testing probes, coaxial probe sockets and pressurized conductive rubber sockets.
-
product
Trace Sulfur Analysis
Some sulfur compounds are known to be not only hazardous but also catalytic poisons. ppb sulfur analysis is conducted by gas chromatography. The Nexis SCD-2030 is a next-generation sulfur chemiluminescence detection system. The dramatically enhanced sensitivity and reliability, the excellent maintainability, and the automation functions, a first for the industry, will improve laboratory productivity.
-
product
Transformer Test Panel/ Setup
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
product
9 kHz Highpass Filter
TBHPF1-9KHZ
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
product
Conductivity Meters
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
product
Electric Servomotor Steering Durability / Performance Tester
Power steering This is an electric servomotor fatigue / endurance tester intended to conduct forward and reverse durability tests of racks and pins.
-
product
Biosensor isoPod
EP352
A compact signal conditioner for monitoring low current, two-electrode (anode and cathode) amperometric sensors.Electrical isolation ensures that readings are not influenced by nearby current sources such as conductivity, or voltammetric electrodes.
-
product
Electronical Load Board 3U CompactPCI (conduction cooled)
046-712
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Explosive Atmosphere Test
This test demonstrates that a part will not ignite while operating in an explosive ambient atmosphere. The tests are conducted at ground level pressure as well as reduced barometric pressures, in a closed explosion-proof chamber.
-
product
Detailed Hydrocarbon Analysis
The purpose of detailed hydrocarbon analysis (DHA) is to determine the bulk hydrocarbon group type composition (PONA: Paraffins, Olefins, Naphthenes and Aromatics) of gasoline and other spark-ignition engine fuels that contain oxygenate blends (Methanol, ethanol, MTBE, ETBE, and TAME) according to ASTM-D6730. PONA analyte identification is conducted by matching retention indices with normal hydrocarbon paraffins. However, chromatograms obtained in PONA analyses have an extremely large number of peaks and their analytes may be mislabeled. Without accurate and reproducible retention indices, this may result in erroneous PONA ratios. The GC-2030 incorporates an Advanced Flow Controller that enables highly precise flow control, and makes it easy to analyze and identify detailed hydrocarbons. Shimadzu offers DHA analysis conforming to the following methods: ASTM-D5134, ASTM-D6729, ASTM-D6730, and ASTM-D6733.
-
product
Breakdown Voltage Tester
ZDS-50B
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
product
HACCP & FSMA Audit Services
The food business is as exciting as it has ever been – but it is becoming more and more complex every year. We know you already go to great lengths to make great food and to keep your customers safe.That said, you’d be surprised to hear how frequently we identify issues our customers didn’t even know about while we are conducting inspections. The truth of the matter is, little issues slip through the cracks from time to time in any food operation. With a process at your plant that runs fast, it is inevitable that you’ll miss something sometime.Here’s a new way to reduce the risk of having issues down the road. FlexXray now offers a new HACCP & FSMA Audit Service to help companies proactively reduce issues and address new requirements for process validation.On an annual basis, we’ll develop a validation process with you and conduct quarterly inspections of your product to ensure and document that your HACCP and FSMA programs are working as planned.
-
product
Fluorescence/UV-VIS Spectrophotometer
Vernier Software & Technology, LLC
Our affordable Fluorescence/UV-VIS Spectrophotometer is designed specifically for upper-level chemistry courses. We've combined the functionality of a fluorometer with the power of a UV/VIS spectrophotometer to allow students to easily and accurately conduct numerous fluorescence experiments with compounds such as quinine sulfate, DAPI, GFP, and tryptophan. Exchangeable LEDs ensure you get the exact excitation wavelength needed for your experiment. To conduct emission spectra experiments simply attach the Vernier Spectrophotometer Optical Fiber. The Fluorescence/UV-VIS Spectrophotometer connects directly to a computer or LabQuest. Data can be collected and analyzed using our Logger Pro software, so there is no need to train students on yet another instrument software.
-
product
Rotor Balancing System
For the purpose of rotating parts balancing in manufacturing scale, it is necessary to conduct measurements with the minimum possible participation of the operator. The Rotor balancing system is intended for measurements related to rotating parts balancing in automated mode.
-
product
Dielectric/Conductivity Sensor
VariconTM
The Varicon sensor is designed for use in presses, molds, bulk materials or laminates where a thin, flexible dielectric sensor is necessary. The Varicon sensor is thin enough to be implanted within a sample or between the plies of a laminate and may be discarded after use. Patterned on a polyimide substrate, the electrode array is designed to allow a choice of three sensitivities, which are selected by cutting off portions of the array at designated lines.
