Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Cable Assembly, 104-Pin D-Type, Female to Female, 2A, 2m, 4-40 UNC Screwlocks
40-970-104-2m-FF
Cable Assembly
This 2m long female to female 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable.
-
Product
Coaxial Attenuators Set
11582A
Attenuator
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Gunn Oscillators
-
Gunn Oscillators are solid state microwave energy generators. These consists of waveguide cavity flanged on one end and micrometer driven plunger fitted on the other end. A gunn-doid is mounted inside the waveguide with BNC Connector for D.C. Bias.
-
Product
Module Spectrum
nRF52840 Series
-
Raytac nRF52840 module spectrum covers MDBT50Q-1MV2, MDBT50Q-P1MV2 and MDBT50Q-U1MV2 series with Chip Antenna, PCB Antenna and u.FL connector for External Antenna option for selection.
-
Product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts And Round Posts (610138200 And 610138117)
510150135
Receiver Module
QuadraPaddle modules are molded on .1” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .1” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-222-HI
-
The 40-230-222-HI (PXI) and 42-230-222-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Connectors, Jumper - Black
INT-10901
-
Jumper for 0.1" (2.54mm) spaced headers. These are also known as a 'shunt'. These mate with the 0.1" square-pin headers and are the 'open' frame style. RoHS compliant.
-
Product
Triple Balanced High IP3 Mixers To 3500 MHz
-
Pulsar Microwave Corporation features a high performance series of triple balanced mixers which offer superior IP3 performance. Optimized to cover specific bands (such as Cellular, PCS, LAN), a +10 dBm LO drive level results in a typical IP3 of +21 dBm, while +17 dBm and +23 LO drive levels result in typical IP3 readings of +30 and +35 dBm respectively. Provide us with your exact frequency ranges and power levels and we will be happy to guarantee an IP3 specification for your application.These high IP3 mixers are available in a number of packaging styles including 8-pin relay headers, TO5 & TO8 cans, flatpacks and connectorized housings. However, the most popular configuration is our miniature surface mount packages which are ideal for large volume applications and can be supplied on tape and reel to utilize automated pick and place assembly techniques.
-
Product
Board Accessories
DN-50
-
DN-50 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with one 50-Pin I/O Connector.
-
Product
3-Pin Power D-Type Cable, Male to Male, 1m
40-970-403-1m-MM
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 0.5m, 45º
A1604F5-C-0A050
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Pressure-Force Cables And Connectors
-
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
Product
PXI 20 Banks of 4 Channel 2 Pole MUX
40-615-022-20/4/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
LXI Microwave Multiplexer, SP4T, 12-Bank, 26.5GHz, 50Ω, SMA
60-803-312
Multiplexer Module
Our 60-803-312 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xSPST, Normally Open
42-145A-001
Relay
The 40-145A-001 (PXI) and 42-145A-001 (PXIe) 50xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PCI Daughter Boards
DB-24RD/24/DIN (24V, D-Sub37 connector, DIN-Rail mount)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
Power Supplies
ZPG-1200B
-
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
USB 3.0 And RJ45 Cat6 To VTAC Interface
YAVAM852
Interface
USB and RJ45 sockets to VTAC VPC contactsHigh speed interface between connectors up to 1GbpsAvoids noise and interferences on signals thanks to VTAC contacts technology
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 1m, Spring Latch
A068SFR-T-5B100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Additional Products: 26 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
PXI/PXIe RF Matrix, 8x2, 1GHz, 50Ω, SMB
42-750A-511
Matrix Switch Module
The 40-750A-511 (PXI) and 42-750A-511 (PXIe) are 50 Ω 8x2 RF matrix modules with SMB connectors suitable for switching frequencies up to 1000 MHz. They are part of a range of 8x2 matrix modules with 50 Ω or 75 Ω characteristic impedance with front panel mounted SMA, SMB or MS-M multiway coaxial connectors.
-
Product
PXI MUX 4 Bank 0f 16 Channel 1 Pole
40-610-021-4/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Circular Connectors
-
Complete range of circular connectors with metal and plastic shells, and crimp and solder terminations for multichannel hybrid electrical/ optical insert arrangements, supporting a wide range of allowable contact voltages and currents, easy environmental sealing and rugged mechanical performance.
-
Product
RF Adapter
-
Passive coaxial components that are used to transfer signals from one connector interface to another.
-
Product
PXIe-1081, 18-Slot (17 Hybrid Slots), Up To 2 GB/s PXI Chassis
790631-01
Chassis
The PXIe-1081 features an all-hybrid backplane to meet a wide range of test and measurement application needs. It features a hybrid connector type in every peripheral slot, enabling flexibility in terms of instrumentation module placement. Additionally, the PXIe-1081 provides 58 W power and cooling and 2GB/s maximum system bandwidth.
-
Product
Cable Assy 9-Pin D-Type, M/F, 0.5m
40-970-009-0.5m-MF
Cable Assembly
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Tinned Ends, 2m
A003PM5-T-5A200
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-507
Multiplexer Module
Our 60-800-507 is a 7 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Cable 96-Pin Micro-D Female to Unterminated, Cut Ends, 1m
40-972B-096-1m-FU
Cable Assembly
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
Alumel, Type K (°C) Contacts
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
