Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
DeepCover Embedded Security in IoT Authenticated Sensing and Notification
MAXREFDES143#
The MAXREFDES143# is an Internet of Things (IoT) embedded security reference design, built to protect an industrial sensing node by means of authentication and notification to a web server. The hardware includes a peripheral module representing a protected sensor node monitoring operating temperature and remaining life of a filter (simulated through ambient light sensing) and an mbed shield representing a controller node responsible for monitoring one or more sensor nodes. The design is hierarchical with each controller node communicating data from connected sensor nodes to a web server that maintains a centralized log and dispatches notifications as necessary. The mbed shield contains a Wi-Fi module, a DS2465 coprocessor with 1-Wire® master function, an LCD, LEDs, and pushbuttons. The protected sensor node contains a DS28E15 authenticator, a DS7505 temperature sensor, and a MAX44009 light sensor. The mbed shield communicates to a web server by the onboard Wi-Fi module and to the protected sensor node with I2C and 1-Wire. The MAXREFDES143# is equipped with a standard shield connector for immediate testing using an mbed board such as the MAX32600MBED#. The simplicity of this design enables rapid integration into any star-topology IoT network requiring the heightened security with low overhead provided by the SHA-256 symmetric-key algorithm.
-
product
44-Pin D-Type Male Connector
40-963-044-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
3-Pin Power D-Type Cable, Male to Female, 2m
40-970-403-2m-MF
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
PXI 10 Banks 0f 8 Channel 1 Pole MUX
40-615-021-10/8/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Cable Assembly, 26-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-026-0.5m-FU
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks)
A200LMR-200LFR-6B100
This male to female 1m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by male screwlocks.
-
product
SMB Connectors
Pasternack SMB connector category has dozens of part numbers, most are RoHS and REACH compliant. SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB connectors are built to precise microwave and RF industry specifications. Connectors in the SMB series are manufactured in jack or plug gender with 50 Ohm impedance. SMB connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this SMB connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
-
product
Visual Fault Locator
OrienTek Optical Technology Ltd.
powerful, mini visual laser source for fiber fault locating. It has attractive design and small size and it is easy to operate. ● Bright red laser at 650nm● Pulsed and CW operation● Outpower: 1mw,10mw,20mw,30mw● 2.5mm universal connector● 40 hours of operation(1mW)● Pocket size design● 1.25 mm adapter for LC (optional)
-
product
LXI Scalable Matrix - 2Amp 10x20 Configurable Matrix Plugin Module
65-219-206
Matrices are created by populating the 65-200 scalable matrix chassis with plug-in modules that provide access to the X axis on 15-pin D-type connectors and the Y axis on 50-pin D-type connectors. The chassis is capable of supporting matrices with a Y axis size of 20 or 40 and X axis sizes up to 60 in increments of 10. Users can specify as many or as few plugin modules as they require and can field upgrade the chassis to extend the matrix size.
-
product
6U Processor Blade
CP62007
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007 is a 6U processor blade based on Intel’s 4th generation core i7/i5 processors using 22nm process technology, supporting up to four cores / eight threads at 2.4GHz. CP62007 supports up to 16GB onboard soldered low voltage DRAM with ECC. It also offers up to 64/128GB SLC/MLC onboard SATA SSD for installing operating system and drivers. The onboard design of memory and SSD enhance the anti-shock and vibration performance dramatically.CP62007’s onboard processor integrates Intel® HD Graphics 4600 controller, supporting a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA. And the VGA resolution is up to 2048x1536. With HDMI/DP/eDP outputs, the resolution can be up to “4K”.CP62007 supports 1x VGA and 2x DP/HDMI/DVI, up to 3 independent or cloned displays.CP62007 uses high speed CPCI connectors on J3 and J4 position for transferring high speed serial signals, such as PCIe2.0, USB3.0 and SATAIII. And the foot-print of high speed connectors are fully compliant with CompactPCI specifications.
-
product
Cables & Connectors
Elegant and creative solutions for convenient signal routing in architecturally esthetic applications.
-
product
20-Pin Scorpion Cable, Female to Unterminated, Cut Ends, 20A, 0.5m
A020AFR-C-2A050
This is a 0.5m long female to unterminated 20-Pin Scorpion cable assembly with cut ends constructed from 19/0.41 (14AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
Connector, PCB Mount, 25 Pin 1.27mm Pitch Micro-D, Male, Straight
C025CMX-1PS-0A
This 25 pin micro-D straight connector is designed to allow users to create their own PCB based connection solution. Screwlocks are provided to secure the connector to its associated cable assembly. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port via a suitable cable
-
product
Rolling Seal 8 Optical Connector (RS8)
The patented Rolling Seal design functions by excluding water and shuttling silt away from the region where the optical ferrules are brought into contact as the connectors are mated. As a result, a clean oil-filled conduit is created for the optical ferrules to connect. The result is a reliable lowloss optical throughput.
-
product
LXI Microwave Multiplexer, SP4T, 4-Bank, 50GHz, 50Ω, SMA-2.4
60-803-604
Our 60-803-604 is a 4 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Male, 0.5m
40-971B-200D-0.5m-MM
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
PXI 2 Amp MUX, Single 8-Channel 4-Pole
40-635-103
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI Expandable 16x16 RF Matrix 75Ohm 1.0/2.3
45-720A-741
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Universal Timer/Counter for CompactPCI
CPCI385
The CPCI385 Universal Timer/Counter CompactPCI card is an ideal solution for automated test and measurement applications. The CPCI385 features two timer/counter inputs. Both inputs have an coaxial connector for the input range of +/- 10 V and high-voltage pins for the input range of +/- 300 V. The coupling of the inputs is either AC or DC. The CPCI385 provides 6 measurement functions: frequency, high-time, low-time, period, counter and phase measurements.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 40GHz SMA-2.9
60-801-407
The 60-801-407 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
CompactPCI 6U 64 bit ATX 8 slot, P1-2s, P3-5l, RoHS
102CPCI608-4157R
CompactPCI 6U 8 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
product
Intel® Core™ Ultra Processor-Based Fanless Open Frame Touch Panel PC
SP2-MTL Series
- Intel® Core™ Ultra H series (Meteor Lake) processor- 10.1"/15.6"/21.5" Projected capacitive touch screen- 3x independent display output, LVDS, DP, USB type C- Full customization for fast integration with all form factors, kiosks, and all-in-one panel PC applications- Extensive I/O and function expansion through board-to-board connectors (Function Modules)- Support PoE by extension module (optional)- Support NVIDIA MXM GPU type A by carrier board (optional)- Pre-compliance EMC testing and high ESD tolerance
-
product
PXI/PXIe USB Data Comms Multiplexer, 16-Channel
42-737A-001
The 40-737A-001 (PXI) and 42-737A-001 (PXIe) are 16:1 USB data communications multiplexers suitable for switching USB1 and USB2 data and power connections using a 78 way D-Type connector. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard.
-
product
SparkFun RJ11 Breakout
This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the board to match a standard telephone wire. Additionally, each board has pin numbers on the back side that match with the pins on the connector.
-
product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
9 Pin D-Type Connector, Male
92-960-009-M
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends
A068SMR-T-5A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Axial Extensometer
Model 3542
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
