Polarization
property of transverse waves which specifies the geometrical orientation of the oscillations.
See Also: Resistivity & Induced Polarization, Resistivity, Polarizers
-
product
Insulation Resistance Measurement
MD 5060x
The Megabras MD-5060x is a smart, microprocessor-controlled, 5kV insulation tester and analyzer. Besides the conventional measurement of insulation resistances up to 5 TW, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
product
TOROIDAL COIL TURNS TESTER
TURNS-TTPT
Digital TURNS TESTER for Counting Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity and DC Resistance.Turns Measurement ( through Toroidal Turns Test Platform) : -> TTPT-100 : 5 Turns ~ 1000Turns-> TTPT-1000 : 500 Turns ~ 10,000Turns
-
product
MPO Visual Cable Verifier Kit
KI-TK872
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
MPO Visual Cable Verifier Kit
KI-TK832
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
VLF Voltage Generators
Fivestar HV Testing Equipment Co., Ltd.
VLF hipot is an AC output tester with an output frequency of 0.1 Hz or lower rather than 50/60 Hz. Although the frequency is very low, it is an alternating current with polarity reversals every half cycle.
-
product
Scalar Feed Horn Antennas
Scalar feed horns are offered as both standard and custom build models with either a circular or rectangular waveguide interface. While scalar feed horns with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. The standard models operate across the full waveguide band and offer 17 dBi nominal gain, 25 degrees half power beamwidth and a -28 dB side lobe level at center frequency. The below standard offering covers the frequency range of 8.5 to 140 GHz. However, other frequencies or gain values are also available.
-
product
POWER PROBE III WITH CLAM SHELL - GREEN
PP3CSGRN
*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground
-
product
Surge Arrester Testing
Weshine Electric Manufacturing Co., Ltd
This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
product
2x8 Coherent Mixer With Single-ended Photodetectors
This page defines the requirement of a special coherent receiver with 8 single-ended photodiode outputs, per customer request. The coherent mixer, consisting of two polarization-diversified 90deg optical hybrids, a polarizing beam splitter and a beam splitter, is exactly same as existing DP-QPSK coherent mixer, and therefore offering same optical performance.
-
product
Terminations & Loads
We have more than 40,000 rf & microwave coaxial terminations in stock we can ship today. We offer these Microwave & RF terminations: SMA Terminations, Type N terminations, 7/16 DIN terminations, 2.92mm terminations, 2.4mm terminations, TNC terminations, smp terminations, minismp terminations, 4.1/9.5 minidin terminations. 4.3/10 terminations, ssma terminations, ssmc terminations, and a few Reverse Polarity terminations. Power levels of 0.5-150 watts. RF / Microwave terminations are also known as dummy loads or 50 ohm dummy loads. Our 1.85mm terminations, are rated to 67ghz. We offer 1.0mm terminations good to 110Ghz.
-
product
POLAR STAR
4ABAC
The high technological content, the great attention to the choice of materials, full compliance with industry regulations, make this instrument a reference (the “North Star”) to orient themselves with efficiency and simplicity in the control of electricity consumption and the main parameters power quality.Polar Star was conceived, designed, built and tested entirely in Italy, and therefore manufactured with quality assurance that distinguishes European products, in the real environment and ethics.His communication skills allow its use in Elcontrol monitoring networks of any size and geographical location. Two available versions 8Base and Top) allow to fit best any application requirement.
-
product
Inrush Current Generators for Zno Production Line
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
product
Wireless Connectivity Multifunction Metal Detector
MS-B158(7)
*Detect metal > 50mm / Ø25mm iron pipe with auto calibration *Laser line generator / Red straight line *Non-contact ACV detection >100V *Continuity check 0 ~ > 20MΩ *Polarity check 3.0V ~ 24V DC
-
product
Waveguide Twists
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
-
product
High Voltage Probe
HVP-40M
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
product
Automatic Power Factor Controller
Nippen Electrical Instruments Co.
NIPPEN Model UNO+ is used for measurement and control of PF using Reactive power compensation. Capacitor banks are suitably switched ON and OFF automatically to provide necessary compensation.An Intelligent switching algorithm (Wear leveling) ensures uniform aging of the capacitors used to achieve the Target PF. An Alarm function ensures protection of capacitor banks against abnormality in voltage, current and sets value of capacitors whenever these are beyond the higher and lower threshold limits.CT polarity is automatically sensed internally in the event of reverse connection.
-
product
Polarization Series
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Polarization Series
-
product
Multi-purpose Tester
DEL-101
Standard Electric Works Co., Ltd
● Mains wiring polarity check.● ELCB/RCD testing.● Measuring ear for line current.● Measuring ear for leakage current.● Helps calculate insulation resistance.● Helps calculate power consumption.● Helps fault finding of standing earth fault.● Fused main adapter.● Appliance testing (with the aid of a clamp meter).● Fused appliance socket.● No batteries required.● HRC fuse inside.● Fused, color-coded universal test sockets.● Universal mains IEC Lead.
-
product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
product
High-Voltage Test Device
PGK 150 / 5 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK H. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 150 kV output voltage with positive or negative polarity* AC voltage testing - up to 110 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
product
Extinction Ratio Meter
Shenzhen Golight Technology Co.,Ltd
The extinction ratio meter can achieve accurate measurement of up to 40dB PER dynamic range. The instrument is precisely controlled by micro-machines, which can quickly and accurately measure the extinction ratio, polarization angle and optical power of the polarization-maintaining device.
-
product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2502
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
product
Dual Polarized Antennas
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20M
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Current measurements for small DC motor*Convenient ＋5V single polarity power supply
-
product
Test Bench for AC Compressors
MS111
The test bench is intended to test AC compressors of wide range of vehicles on R134a refrigerant. The equipment detects failures of a vehicle unit before its mounting in a car, whether it is a remanufactured, repaired unit or a used one. In the process of testing, data is shown on LCD display. It gives an opportunity to follow testing results realtime, save and/or print them due to software special features. Unit fixation mechanism is very flexible: a compressor can be easily fixed, no matter what kind of fittings it has. Units with electromagnetic clutch or electromagnetic valve can be tested both separately and simultaneously. Peculiar features of electric commutation are considered, connection polarity is identified automatically, indicator on the control panel indicates on presence of a diode in a circuit.
-
product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
product
Digital Multimeters
ST-3201
Standard Electric Works Co., Ltd
● Display : 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity : Automatic, (-) negative polarity indication.● Zero Adjustment : Automatic.● Over Range Indication : Highest digit of (1) or (-1) is displayed. ● Low Battery Indication : The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate : 3 measurements per second, nominal.● Operating Temperature : 0ºC ~ 50ºC, 70% R. H.● Storage Temperature : -20ºC ~ 60ºC, 80% R. H.● Accuracy : Accuracy specifications at 23 ± 5ºC, less than 75% R. H.● Power : Single, 006P 9 volt battery● Dimensions : 128(L) × 72(W) × 33(D) mm.● Weight : Approx. 183g
-
product
PXI Solid State Multiplexer, 30 Amp, Single 6-Channel
40-667A-012
The 40-667A-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Amplitude Detectors with Isolators
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacity to handle a maximum RF input power of up to +17 dBm. The RF interface of these detectors is a standard waveguide with an integrated Faraday isolator to improve the port VSWR. The output voltage polarity is negative and the connector type is a female SMA. Other configurations are offered as custom models.
