Strain Gauge Amplifiers
-
Product
Digital Pressure Gauge
m1
-
AMETEK Sensors, Test & Calibration
The m1 digital pressure gauge maintains 0.2% of reading accuracy from -10 to 50°C. Accuracy is not affected by dropping, over-pressure, vibration, temperature, or rapid pressure change. Available as a 30 psi digital manometer.
-
Product
Low Noise Amplifier
-
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
Product
Digital Force Gauges
-
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, ITA
910121157
-
Used to verify the depth setting of the center conductor of the ITA mini coax contacts.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Wide Range Vacuum Gauge
HVG-2020B
-
The HVG-2020B wide range, dual sensor vacuum gauge takes measurement to the next level. With a Piezo based sensor and a thermal based Pirani sensor accurately and confidently measure pressures across seven decades. The Piezo sensor is media isolated, gas composition independent, and periodically zeroed by the Pirani sensor. An ambient thermal sensor enables the instrument to adjust for temperature and therefore better accuracy.
-
Product
Mechanical Force Gauges
-
Imada mechanical force gauges are highly accurate instruments used to test the quality, strength or functionality of component parts or products. Imada mechanical force gauges check both compression and tension (push or pull). Peak force can be captured using the peak indicator needle and the tare ring compensates for the weight of attachments. Imada force gauges are constructed with a heavy-duty metal case and all metal components to enable them to retain their calibration for years with proper care. These mechanical force gauges never need charging or batteries and are intrinsically safe in hazardous environments.
-
Product
Microwave Power Amplifier 1/4 Watt 10 MHz to 50 GHz
GT-1051B
-
The Spanawave/Giga-tronics GT-1051B Microwave Power Amplifier offers linear high-power amplification across muultioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
Product
Digital Strain Gauge Sensor
ZET 7111
-
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1k
40-265-204
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Force Gauges
-
Morehouse Instrument Company Inc.
Minimize user error and achieve higher accuracy with Morehouse Digital Force Gauges. These instruments display the applied force value directly and do not need an interpretation table. Morehouse analog Ring Force Gauges can also be upgraded to the new digital system.
-
Product
Operational Amplifiers
-
Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.
-
Product
QuickLink Solder-In Starter Pack for use with Dx20 Amplifier
Dx20-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Broadband High Power Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's broadband high power amplifiers are available for operating frequencies from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 2 watts to over 500 watts. Based on state-of-the-art GaN, GaAs, LDMOS power devices and MMICs, KeyLink designs and manufactures SSPA(solid state power amplifiers ) with excellent performance in terms of high efficiency over ultra-wide working band, high reliability and ruggedness.
-
Product
Benchtop Femtosecond/Picosecond Lasers and Amplifiers
-
The systems feature a portable design with user-friendly front panel control knobs for adjustment of output parameters, such as power, pulse width and repetition rate. With wavelength options of 780 nm, 850 nm, 1310 nm, and 1550 nm, pulse widths as low as < 0.3 ps, and GHz low-jitter synchronization signals, these systems provide ideal optical sources for high speed transceiver conformance testing and photodiode characterization.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
BG Series Bass Amplifiers
-
250 Watt Bass Combos with Built-In TonePrints and Integrated Tuner.
-
Product
Scaling Amplifier
SIM983
-
Stanford Research Systems, Inc.
The SIM983 Scaling Amplifier provides fine adjustable gain and offset control for analog signals. Both gain and offset are set with 3½ digits of resolution, and the signal path has more than 1 MHz of bandwidth.
-
Product
Split Type Ultrasonic Level Gauge
HR9100D
-
HighReach Measuring & Controlling System Co.,Ltd
1. Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments. 2, patented technology / one ring patented sound wave intelligent technology software can Intelligent outgoing analysis without any debugging and other special steps, this technology has the function of dynamic thinking, dynamic analysis 3, high precision / sound wave intelligence owned by our company The patented technology greatly improves the accuracy of the ultrasonic level gauge, the Liquid level accuracy reaches ±0.2%, can resist various interference wavesThe instrument is a non-contact instrument, not Direct contact with liquid, so the failure rate is low. The instrument provides a variety of installation methods, users can use this . The Instrument Manual Calibrate to 5. The Protection of The Level of Multiple Protection / IP67 & Instrument Reaches; INPUT and Output Lines All have have Lightning Protection and Short Circuit Protection.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
Product
Shunt Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
-
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
NI-9235, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
785995-01
-
10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Laser Sources and Amplifiers
-
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
