Wire
See Also: Contacts, Harness, Connectors
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
Professional Cordless Circuit Tester
CT8002
-
No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.
-
Product
Energy Meters
-
Contrel Elettronica s.r.l. Company
Energy meters for efficient management of energy consumption. Total and partial energy meters (resettable). Equipped with input / output and communication module. From direct single-phase connection in a single module to three-phase wiring via CT. High precision. MID versions: certified energy meters for sub-measurement.
-
Product
AC & DC Aging Test Equipment for Arrester Valve Plate
-
Shanghai Guantu Technology Co., Ltd.
The arrester is usually connected between the live wire and the ground, and is connected in parallel with the protected equipment. When the overvoltage value reaches the specified operating voltage, the arrester will act immediately, flow the charge, limit the overvoltage amplitude, and protect the insulation of the equipment; when the voltage value is normal, the arrester will quickly return to its original state to ensure the normal power supply of the system.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 2m, 29 Wires
A051KMR-F-HA200-29
Cable Assembly
This is a 2m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
Product
Mobile Comm DC Source w/ Battery Emulation
66321B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
Product
High Performance Cables And Accessories
-
Cables are designed and manufactured by Celadon. Cables are available in lengths custom to the half-meter, and can be manufactured with a variety of industry standard connectors, such as coaxial, triaxial, Type8, Edge 24/48 or 35/70, DSub 9, 15, 25, or 50; or advanced multi-contact. Depending on the overall size of the final product, an anti-abrasion sheath may be used to prevent wire wear.
-
Product
Cable Assy 78-Pin D-Type M/F 0.5m
40-970-078-0.5m-MF
Cable Assembly
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
All-In-One Toner & Probe Kit
MT-7068
-
The MT-7068 All-in-one Toner & probe Kit lets you use Toner and Probe to validate and troubleshoot wiring on RJ11/RJ45 cables and connectors, USB, F, BNC, and RCA connectors, and it also supplied with alligator clips to work with. The MT-7068 Toner detects telephone and Ethernet service, indicates polarity and active line numbers on voice circuits, and indicates active pair number on Ethernet circuits. The MT-7068 Toner and Probe also provide standard functions such as visual and audible signal strength indication, analog toning/detection, and continuity testing. It is ideal for all maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling , etc.
-
Product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Cut Ends, 5A, 0.5m
A050FFR-C-0A050
Cable Assembly
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
BNC (M) To Multi-Stacking Banana Plugs
3957
-
BNC (m) to multi-stacking banana plugs. Converts BNC (Female) cables/connectors to top/side stackable banana plugs for test versatility. BNC connector and banana plugs are molded directly to the wire for pull strength durability anddust/moisture resistance.
-
Product
The Ultimate Circuit Tester Kit
28640
-
The tester kit tests low voltage up to 28 volts. Also finds electrical shorts, checks polarity, detects battery drain, and checks circuits from a distance. Heavy-duty coil cord extends over 8 feet. Detachable, spring-loaded hook pulls the center of the wire into the probe every time. Attach alligator clip to the probe when a clip-on connection is needed.
-
Product
Dry Arc Resistance Tester
-
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 0.5m, Spring Latch
A068SFR-F-5B050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Configuration Block For The 34934A Quad 4x32 Reed Matrix
34934C
Terminal Block
This configuration block provides flexible options for wiring rows and columns to D-Sub connectors.
-
Product
20-Pin GMCT Male Connector, 16A, With Backshell
40-960-020-16A-M
GMCT Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. Also included is the backshell with screwlocks and cable clamp.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Away From Pin 1
A050DF4-C-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Multiple Channel Burn In Power Supply
MCPS
-
The most important features of this burn in power supply is its ability to hold a constant output for each channel even in the event that a unit under test on one channel may short and fail. Since each channel has it''s own transformer, no glitches or voltage spikes can get into any of the other channels. This image shows the results as the second channel from the left is shorted with a small wire and the circuit breaker pops out. Used for burn-in testing and other timed testing where power isolation is required. Very basic simple circuit, see schematic below. Cleans and frees up benchtops, burn in racks and work space clutter. Available in benchtop or rackmount.
-
Product
Vibrating Wire Dataloggers
-
Vibrating-wire dataloggers have the built-in capability to measure vibrating-wire sensors. These dataloggers use patented spectral analysis technology.
-
Product
Linear Hall Sensor
-
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
Product
Banana-Triax Adapter For 4‑Wire (Kelvin) Connection
N1297B
-
The N1297 Series is a collection of banana-triax adapters for the Keysight B2900 Series precision source measure unit (SMU). It consists of both 2-wire as well as 4-wire connection requirements.
-
Product
Wired Serial Device Server
SD-300
-
The Silex SD-300 and SD-310AN are designed to easily connect and share RS-232 serial devices over a wired or wireless network. Industrial automation, building automation, medical devices, security access and control, point of sale devices, LED signs, bar code/label and other specialty printers, or virtually any other device with a serial port can be now be enabled with secure, robust wired or wireless network capability.
-
Product
Value Added Services
-
For over three decades, Teledyne RF & Microwave has built a strong heritage delivering advanced value added services to the military, space and industry sectors of aerospace. With test capabilities up to 40 GHz, Teledyne offers chip and wire assembly of products ranging from single die through complex hybrids which can then be submitted to a combination of customer-specified RF and DC testing and environmental screening. We offer a complete portfolio of screening and testing services for device sorting, labeling, lead forming and tinning, and tape-and-reel packaging, as well as LAT services on packaged devices or bare-die, including diodes, transistors, and MMICs.
-
Product
Circbord
8007
-
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole pattern on component side. Overall Ground Plane pattern on wiring side.0.080” diameter isolated solder pad around holes oncomponent side. Plane surfaces solder coated for user convenience.
-
Product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-025-2m-FU
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
5 A portable digital micro-ohmmeter
MPK-254
-
The MPK-254 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1 mA up to 5 A.
-
Product
PCB Connectors
CMD Series
-
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
Product
Vison Inspection System
-
High Speed stroboscopic 2D vision inspection system for die attached and wirebond quality in back-end semiconductor processes. User friendly HMI for easy recipe creation and management. Able to configure with various defect identification module. (Strip Mapping, Inker, Scriber, Pucher, Bristle, Laser wire cutter and Laser clip bonding cutter.)
-
Product
Probes, Clamp-On
EM-6980 | 20 Hz – 50 KHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
Cable Assy 26-Pin D-Type M/M 0.5m
40-970-026-0.5m-MM
Cable Assembly
The 26-Pin D-Type cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 26-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
