Electrodes
-
Product
Rotating Ring Disk Electrode
RRDE-3A
-
RRDE-3A is a constant rotation system for use in hydrodynamic modulation rotating ring disk electrochemistry. A 7 mm diameter electrode with short stainless steel shaft provides for a miniature and concentric circle electrode system that is capable for highly accurate rotation and modulation even at radial modulation rates or wave forms.
-
Product
Resistance System Kit
PMK-151
-
The PMK-151 Basic Measurement Kit has all the functionality of the PMK-152, but adds computer downloading capabilities. It contains all the instruments you need to take a variety of resistance measurements.The PMK-151 includes Prostat's PRS-801 Resistance Set with modified 5 pound conductive rubber electrodes, the PRS-801 wide range resistance meter, and Prostat PRS-801 Connectivity software for computer data downloading. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
Product
SEM Dual-Purpose Glassy Carbon Electrode
DP-1-3
-
Dual-purpose glassy carbon working electrode for electrochemical measurements and SEM analysis. Available in 2-6 mm diameters with PTFE or PEEK housing, plus magnetic or detachable electrode configurations for surface characterization workflows.
-
Product
Field-installation Type Simplified Fluoride Ion Concentration Meter(Four-Wire Transmission)
HC-200F
-
HC-200F is connected to a fluoride ion electrode (1009) to detect free fluoride ions in the sample water.(Total fluorine is not detected.) It is suitable for fluoride ion monitoring in effluent from factories, e.g., those of semiconductor FPD and glass manufacturers.
-
Product
Small-Volume Sealed Electrochemical Cell (10–30ml)
SV-1
-
Compact sealed electrochemical cell available in 10ml, 20ml, and 30ml volumes. Ideal for micro-volume experiments requiring a stable three-electrode setup. Electrodes not included.
-
Product
Electrical Tomography Software
Res2dinv
-
This very popular software, developped by M.H.Loke, uses the method involving the Sasaki minimum squares inversion (1992) to produce a 2D sub-soil model starting from the data of apparent resistivity (up to 2000 electrodes). It is completely automatic and does not require that the user formulates a starting model. When using a state-of-art computer, the inversion of a single pseudosection will require only a few minutes.RES2DINV supports spreading types like Wenner, Schlumberger, Pole-Pole, Pole-Dipole, line Dipole, equatorial Dipole and other non-conventional spreading types.
-
Product
200μm Flexible PET Interdigitated Electrode Chip
FPL1
-
200μm flexible PET IDE chip designed for biosensing, gas sensing, and humidity monitoring applications.
-
Product
Platinum Sheet / Platinum Anode-Cathode Electrode
PSP1
-
PSP1 Platinum Sheet / Platinum Anode-Cathode Electrode is a research-grade electrochemical electrode for use as a working electrode, counter electrode or custom laboratory assembly. It is suitable for voltammetry, electrocatalysis, corrosion testing, sensor research and electrochemical cell development.
-
Product
Single Carbon Screen-Printed Electrode (SPE)
-
A single carbon screen-printed electrode (SPE) designed for electrochemical sensing, biosensor development, environmental monitoring, and laboratory research with excellent reproducibility and customizable electrode configurations.
-
Product
PEEK Platinum Sheet Electrode Clip
PCP1
-
PEEK platinum sheet electrode clip designed for securely holding working electrodes in electrochemical experiments. Compatible with carbon paper, carbon cloth, ITO glass, metal foils, and other flat electrode substrates. Manufactured from chemically resistant PEEK with a platinum contact for excellent electrical conductivity, making it suitable for electrocatalysis, fuel cell research, corrosion studies, battery testing, and laboratory applications.
-
Product
Open Flanges Test Rig
-
Flexible cell dimensions: cells of Ø 8 to Ø 80 mm (or square till 70x70 mm) can be successively installed Quick start of experiment: less than 20 minutes to remount a new cell with different dimension, thanks to the simple design without sealing Other SOFC components: the open flanges test rig is also useful for conductivity measurements (electrolyte, electrode material, interconnect etc.) and sealing tests End of broken cells and secure testing: the cell is squeezed by a soft alumina felt that prevents any damages, the excess fuel burns continuously in the alumina felt at the cell edges
-
Product
3 Mm Glassy Carbon Disk Electrode
CGC1
-
3 mm glassy carbon disk electrode designed for electrochemical research, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), corrosion studies, electrocatalysis, and sensor development. Manufactured from high-purity glassy carbon with excellent chemical stability, a wide potential window, and low background current. Compatible with CHI104 systems and customizable for laboratory and OEM applications.
-
Product
MyoWare 2.0 Muscle Sensor
-
Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks... but what if we could take the buttons, levers and joysticks out of the equation and control it with our muscles? The MyoWare® 2.0 Muscle Sensor is an Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies that allows you to do just that! The MyoWare 2.0 Muscle Sensor has been redesigned from the ground up with a new easy-to-use, compact design and upgraded with the latest and greatest chipset improving sensor performance and reliability. The innovative snap connector system eliminates the need to solder connections for the MyoWare 2.0 ecosystem. It's that easy: stick on a few electrodes (not included), read the output voltage and flex some muscles!
-
Product
Dielectric/Conductivity Sensor
Micro-VariconTM
-
The Micro-Varicon sensor is a miniature, thin, flexible dielectric sensor designedfor cost-sensitive use where space is limited. The electrode array is patterned on apolyimide substrate, and the Micro-Varicon sensor can be supplied with or withoutTeflon insulated leads.
-
Product
Graphite Disc, Rod & Sheet Electrodes
OT1-3
-
High-purity graphite disc, rod and sheet electrodes for electrochemical research. Suitable for CV, LSV, EIS, corrosion testing, electrocatalysis and custom cell assemblies, with standard graphite disc diameters and custom rod or sheet formats available.
-
Product
Unsealed Jacketed Electrochemical Cell – Temperature-Controlled
DL-1
-
DL-1 Unsealed Jacketed Electrochemical Cell – Temperature-Controlled is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model. The cell can be matched with working electrodes, reference electrodes, counter electrodes, gas ports, quartz windows, PTFE covers, jackets, and custom fittings according to the experimental setup. Please confirm the required volume, sealing method, electrode ports, and application conditions before ordering.
-
Product
Rebar
-
Continuously monitors the coating line process as reinforcing bar runs through the RBRS dual-roller wet sponge electrodes unit. When a holiday is discovered, a red light flashes at the appropriate station on the detector unit for a visual indication, and the unit sends an eletrical output to a plug on the back of the unit. The MSRB signal output plugs drive any 120 Volt AC customer furnished horn, bell, recorder or computer.
-
Product
Earth Tester
TAURUS PRECIOHM ET
-
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
Product
Long Term Test Kit
-
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to the intake of electrons at the electrode, the chromium ion will transform to chromium oxide and be deposited at the cathode triple point. In such a case, the long term test kit is used. The Inconel 601 flange is equipped with an alumina housing (>96 % Al2O3) and the air (or other gas) is led through an alumina tube. The long term test kit is fully compatible with other functionalities proposed with the Open Flanges™ test Set-Up as the integrated steamer or the small pellet test kit. The long term test kit can be implemented on the fuel, on the air or on both sides.
-
Product
Graphite Sheet Electrodes
OT1-2
-
High-purity graphite sheet electrodes for electrochemical research, current collectors, electrocatalysis and corrosion testing. Custom sheet dimensions, exposed areas, mounting holes and lead-connection options are available for laboratory cell designs.
-
Product
Induction Style Control Relay
1500
-
A floatless liquid level control system from B/W Controls consists of a relay of the proper type, a holder designed to support one or more electrodes or probes in the liquid container, and the corrosion resistant electrodes themselves.
-
Product
Multi-Potentiostat
1000C
-
The model 1000B series is a computerized 8 channel potentiostat. The system contains a digital function generator, multiplexed data acquisition circuitry, and a multi-potentiostat that can work with eight independent cells or eight working electrodes in the same solution with common reference and counter electrodes. The potential control range is 10 V for all channels, which can be set at independent potentials or the same potential as the primary channel, so that they can sweep or step potentials together with the primary channel.
-
Product
Handheld Water Quality Meters
LAQUA DO220
-
Measures dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation0.01 mg/L or 0.1% DO resolutionCompensates salinity, temperature, and atmospheric pressure Allows up to 2 calibration points using galvanic DO electrode°C & °F temperature readingsWith real-time clock and date/time stamp for GLP complianceAuto log data; built-in memory can store up to 1000 dataAuto stable, auto hold, and real-time measurement modesAuto shut-off (programmable: up to 30 minutes)Built-in electrode holder allows 2 electrodes to be attached Monochrome LCD with white LED backlight: 50 x 50 mmPhono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slipPowered by 2 x AA batteriesPackaged with galvanic electrode in carrying case3 years meter warranty
-
Product
Single Cell Hardware
-
A Fuel Cell Hardware Assembly consists of a pair of Poco Graphite Blocks with a precision, machined flow-pattern (pattern is serpentine unless otherwise specified by the customer), and a pair of gold plated connectors fastened with aluminum end plates. Gas inputs and outputs are through Swagelok fittings. A thermocouple well and two cartridge heaters are also provided. A single Anode Reference Electrode may be added for an additional cost. The FCT Cell Hardware does not include a Membrane Electrode Assembly (MEA).
-
Product
3D inversion geophysical software for Resistivity and Induced Polarization Data
RES3DINV
-
This program is designed to invert data collected with a rectangular grid of electrodes. The arrays supported include the pole-pole, pole-dipole, inline dipole-dipole, equatorial dipole-dipole and Wenner-Schlumberger. The RES3DINV program uses the smoothness-constrained least-squares inversion technique to produce a 3D model of the subsurface from the apparent resistivity data alone.
-
Product
Multi-probe for Ammonium and/or Nitrate
S470
-
S470 is a complete family of Ion selective electrodes (ISE) probes suitable for monitoring the performance of the ammonium ion (as NH4+ or NH4–N) and nitrate ion (as NO3– or NO3–N) in a liquid matrix.
-
Product
Accessories for Earth Resistivity (VES)
Electrodes
-
Earth resistivity / Accessories for earth resistivity (VES)
-
Product
pH 550 Benchtop pH Meter Kit with Probe, Stand, and pH Buffers
-
The PH 550 benchtop pH meter features a microprocessor chip which provides automatic temperature compensation, data storage, parameter setup, and Max/Min reading display. The meter offers a pH range from 0 to 14 and a three-point automatic calibration, with the ability to recognize standard buffer solutions (USA or NIST series). The advanced digital processing technology improves meter response time and measuring accuracy. A stable reading display icon appears when the measuring value is stable. The 3-in-1 combination pH electrode measures pH and temperature simultaneously. The compact meter includes a detachable electrode holder and three bottles of pH buffer solution. It has a dustproof and spillproof rating of IP54. Connectors are protected by silicone seal caps.
-
Product
Potentiostats
-
A potentiostat is a device that controls the potential between a pair of electrodes while measuring the resulting current flow. The resulting electrochemical plot is then used to determine various parameters relevant to the experiment.
-
Product
5μm Transparent Quartz Interdigitated Electrode Chip
TIM1
-
5μm transparent quartz IDE chip designed for MEMS, gas sensing, bioelectrochemical, and photoelectric applications.
