Signal Integrity
See Also: Signal, Signal Sources, Signal Processing, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
EMI Filters And Application-Specific Integrated Products (ASIP)
-
An electromagnetic interference (EMI) filter is used in electronic circuits to improve system immunity against unwanted external electromagnetic signals from neighboring circuits and to avoid emitting radiation (“noise”) that may disturb the same nearby circuits by canceling unwanted frequencies.
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 64 Position
510104134
Receiver Module
Primary mating module 510108101. (May mate with other ITA modules, as well.)
-
Product
GPS Antenna Signal Splitter 4 Way, SMA Jack, 1000 - 2000 MHz, 50 Ohm
GPS410
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
Product
Signal Generator
-
bsw TestSystems & Consulting AG
Especially for signal generation above 50GHz and in waveguide bands is done with a standard lower microwave generator and then the signal is frequency multiplied to get to higher frequencies. The frequency multiplied signal may optionally be filtered to make it spectrally pure and/or amplified to come to an appreciable signal level.
-
Product
Precision Signal Source/Function Generator
-
A portable, dual-channel voltage, frequency and charge signal generator with accuracies exceeding most high-cost laboratory function generators.
-
-
Product
Cable Assembly, Twisted Pair, Differential Signals, 78-Pin D-Type Male to Female, 2m
A078DMR-078DFR-9A200
Cable Assembly
The A078DMR-078DFR-9A200 is a 78-Pin Male to Female D-Type Cable Assembly with twisted signal pairs suitable for differential signals and is designed to be used with Pickering's 40-200 fault insertion switch.
-
Product
GNSS Signal Simulator
sUTP 5017
Simulator
With the increasingly complex RF landscape, expectations for validation and functional testing of GNSS equipment are also rising. A large number of different navigation signals need to be reproduced under conditions that are as realistic as possible. The additional generation and injection of interference into the GNSS signals are supposed to simulate the real environment.
-
Product
4-Channel Strain Gage Amplifier Module for the SCS-800 Signal Conditioning System
SCS-824 Series
-
The SCS-824 series provides 4 channels of strain gageinputs for the SCS-800 signal conditioning system. TheSCS-824 series interfaces all strain gage types, fromsingle-element quarter bridges to 4-element full bridges
-
Product
Signal Conditioners
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
Metra has been manufacturing amplifiers for piezoelectric transducers for over 50 years. We offer economic charge amplifiers and signal conditioners for IEPE transducers including microphones.
-
Product
RF Signal Generators
-
Compact and reliable microwave and RF Signal Generators for use in automated testing environments, production verification, EMC testing, educational institutions, aerospace, defense projects, LTE engineering, satellite communications, CATV, 5G design…
-
Product
HPx-310 Radar Signal Output Card
-
The HPx-310 Radar Signal Output card is a replacement for the HPx-300, form, fit, and function. It generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars.
-
Product
Mixed Signal Oscilloscope 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014G
Oscilloscope
The MSOX3014G 100 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Signaling Control and Monitor Equipment
MS 1303
-
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded For Wire Wrap With Anti-Rotation (610 138 122)
510151127
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Mixed Signal Oscilloscope: 8 GHz, 4 Analog Plus 16 Digital Channels
MSOV084A
Oscilloscope
8 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.04 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Power Integrity Analyzer Reference Solution
-
The power integrity analyzer reference solution is a hardware-based solution with the Keysight Infiniium S-Series 10-Bit ADC oscilloscope and probes, including the N7020A power rail probe that lets you see the true AC power noise on your DC power line and supports up to +/- 24 V offset and the N2820A high-sensitivity current probe that can measure down to 50 uA.
-
Product
Mixed Signal Oscilloscope: 100 MHz, 2 Analog Plus 8 Digital Channels
MSOX2012A
Oscilloscope
100 MHz2 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
Class 1 Integrating Sound Level Meter System
NK021
-
This NK021 system includes a class 1 integrating sound level meter, class 1 acoustic calibrator, protective microphone windshield and is supplied in a hard wearing kit case.
-
Product
Amplifier Characterization With Wideband Modulated Signal
N5245BV
Amplifier
The N5245BV provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for amplifier measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements.
-
Product
Typical Advanced Mixed Signal Driver Card
-
A wide range of Driver card are available suitable for HTOL, THB, LTOL, and HAST test applications. All device technologies are catered for whether it be Digital , Analogue, Mixed Signal, low voltage <0.5v, high voltage >>3KV.
-
Product
GNSS Signal Generation System
GSS6300
-
The Spirent GSS6300 has been specifically designed to facilitate high-volume production testing for GNSS-enabled applications. Capable of generating a single channel of multiple GNSS in the L1 band individually or concurrently, the GSS6300 offers the fidelity and reliability needed for final functional testing of high-value critical systems.
-
Product
Floating 6-Ch Integrated Power Source
PM0650
-
The pulse channels provide voltage pulses with duration control 10us to 100ms, and measures current. The combination of capabilities provides a versatile solution on fulfilling the wide range of requirements on testing a device. The PM0650 may be floated up to ±1500V to facilitate HV isolation test of devices where outputs may be connected directly to line voltages.
-
Product
Multi-Band Dual-Channel Receiver/Combiner, Modular Unit with Integral Tracking Receivers and Bit Syncs
LS-28-DRSM Series
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
Signal Averaging eXpert FPGA DSP Feature for CompuScope Digitizers
Digitizer
Utilizing the eXpert Signal Averaging Firmware on a GaGe CompuScope Digitizer allows users to detect a small repetitive signal in a noisy environment by conducting rapid signal averaging completely on the digitizer's onboard FPGA with absolutely no host system CPU loading.
-
Product
Signal, Insert, Receiver, QuadraPaddle, SIM, 1 Slot (not loaded- for discrete wiring only)
510180101
SIM Insert
Signal, Insert, Receiver, QuadraPaddle, SIM, 1 Slot (not loaded- for discrete wiring only).
-
Product
Digital Signal Processor Card
CHAMP-AV8
-
Curtiss-Wright Defense Solutions
The CHAMP-AV8 6U OpenVPX digital signal processor (DSP) combines the floating-point performance of the 3rd generation Intel Core i7 processors with the substantial bandwidth and system-enabling features of the 6U OpenVPX form factor. Utilizing a pair of 2.1 GHz quad-core processors featuring the Advanced Vector Extensions (AVX) instruction set, the CHAMP-AV8 DSP card delivers up to 269 GFLOPs.
-
-
Product
Signal Generator, Audio, Handheld, 1 Channel, 150kHz, AM, US Plug
72-505
-
*Hand held audio generator*20Hz to 150KHz in 46 steps*±0.5dB sine wave output 1.2V RMS (no load) and square wave output SV p-p max (no load)*Dimensions: 150mm × 83mm × 25mm*Low battery indicator
-
Product
Manual Model for Integrated use in VLT Test Lanes
VLT 0939TL01
-
Manual Headlight Beam Tester with Same measuring Techniques as our Fully Automated models. This Manual operated model for use in VLT Test Lanes, with cable boom connection to the Test lane Computer. Including rechargeable battery pack and charge.
