Pickup
-
Product
Probe & Pickup
1035
-
TESCO’s Catalog No. 1035 Probe & Pickup combines the best of communication between a PC and a meter. No longer do you have to disconnect the pickup to reconnect to a PC with this all-in-one device. Save time with less hassle.
-
Product
Piezoelectric Vibration Pickup
PU-6GHT6
-
*High-sensitivity type for sensoring*low-rotation from 0.2Hz
-
Product
SECONDARY IGNITION PICKUP
MD75300
-
*Safely acquire high voltage waveforms with this high impedance, active pickup*Works with spark plug wires and coil on plug ignitions with MDAUTOWAVE, AUTOWAVECAMO and MDAUTOWAVE2*Adjustable sensitivity increases waveform acquisition accuracy
-
Product
Piezoelectric Vibration Pickup
PU-671D
-
*Upper outlet*Compliant with waterproof (IPX7) and suitable for high temperature (-10℃ to 150℃)
-
Product
Optical Pickup
1037-DTS
-
TESCO introduces a new optical pickup (Catalog No. 1037-DTS) for one way meter communication through the calibration LED found on most solid state meters. The pickup senses infrared pulses from ANSI compliant meters for complete, automatic testing.
-
-
Product
Piezoelectric Vibration Pickup
PU-8ALSF
-
*Side outlet type with assembled *cap nut*Built-in amplifier*Use up to 150 ℃ enabled
-
Product
Vibration Pickup
-
Constructed so that each Piezoelectric element has shear that is proportional to applied acceleration between the poles. It is useful for low frequency vibration measurement even in the environments of large temperature change because of it is hard to be effected by the Pyroelectricity. Furthermore, it is less sensitive to the strain in the base.
-
Product
Portable Optical Pickup
OP200x
-
Power Measurement Technologies Inc.
The OP200x is a versatile, lightweight, portable instrument designed to detect watt-hour meter disk rotation, light pulses, LCD segments and contact closure events.
-
Product
Piezoelectric Vibration Pickup
PU-7ALT6
-
*Upper outlet type*Use in water up to 15 meters*depth enabled
-
Product
Piezoelectric Vibration Pickup
PU-626E
-
*Connector type with upper outlet*Waterproof (IPX6), suitable for a wide range
-
Product
Piezoelectric Vibration Pickup
PU-661D
-
*Side outlet type*Waterproof (IPX7) and suitable for*high temperature(-10℃ to 150℃)
-
Product
Vacuum Pen
-
Stand-alone vacuum pick-up system used for pick and place functions. Requires shop air or can be air powered through TS350 Series or TS500R dispensers/controllers. Features an adjustable vacuum control knob to set desired vacuum. Maximum operating pressure 100psi (6.9bar).
-
Product
Piezoelectric Vibration Pickup
PU-6ALSF
-
*Side outlet type*Easy to remove due to cap nut type*Use up to 80 ℃ enabled
-
Product
Gated Integrator | Boxcar Averager
GIA100
-
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
Product
Measuring Wheel
B20-S
-
Simple and light Measuring Wheel B20-s can measure up to 10,000m at 10cm graduation.The counter is indicated in 5 digits and has reset button. When we use Leak Noise Correlator LC-2500, we need to input the between pick-up sensors.
-
Product
Compact Inspection Camera
-
Fits in your pocket or clips on your beltAffordable1 meter drop-proofLong, thin camera-tipped probe with excellent depth of field penetrates tight, hard-to-reach spacesProbe is waterproof, holds its configured shape, and coils inside clamshell case for storageFour camera-lighting LEDs produce bright, crisp video on large color LCDFour screen controlsFour useful probe tip accessories (pickup hook, magnetic pickup, 45 mirror, thread protector)
-
Product
Lock-In Voltage Preamplifier
SR552
-
Stanford Research Systems, Inc.
The SR552 Voltage Preamplifier is designed to work with SRS lock-in amplifiers, providing gain where it is needed most?right at the experiment. The preamplifier minimizes noise and pickup in the connecting lines and can reduce measurement time in noise-limited experiments.
-
Product
Automated Pick And Collection Tool Of Cell Colonies
CELL PICKER
-
Pickup and Remove Cell Colonies with Complete Freedom
-
Product
Seismic Sensors & Transducers
-
Displacement Pickups are vibration transducers that incorporate a spring-mass system with eddy-current damping using a frictionless pivot. This pivot is a spring flexure that serves as the ‘spring’ and a moment arm attached to the pivot serves as the ‘mass’, which allows resolutions down to the micro inch range. At frequencies above 50Hz, the mass remains fixed in space and becomes an inertial reference.
-
Product
AC-Powered, AC Voltage Monitor, Adjustable
VMA
Voltage Monitor
NAI’s VMA is a field-adjustable, AC-Powered, AC Voltage Monitor used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits.High and low voltage limits, and "pick-up" and "drop-out" time delay are field-adjustable. The VMA voltage monitor is ideally suited for rugged defense and industrial applications.
-
Product
Speed Switch
DR1000
-
Features • Works with remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • DPDT relay output • Under-speed setpoint adjustment from 0.5-5,000 rpm (at 8 PPR) • Terminal blocks for easy wiring • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Rugged explosion proof / NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
Product
EZ Tach +Plus Automotive Tachometer
328
-
*Versatile instrument can measure RPM on a wide variety of engines from string trimmers to automotive. *Reads engine revolutions from 0 to 20,000 RPM *Picks up RPM signal wireless or with supplied inductive pickup *Great for setting idle speeds! *Built-in LED Flashlight which can be used while taking measurements *Backlit LCD display *Accuracy +10 RPM
-
Product
Lightweight Vehicle Surveillance System
LVSS
-
The skid-based LVSS converts a standard commercial pickup into a rapidly deployable command and control center. Within minutes, a single operator can set up the LVSS and report for full perimeter duty from the comfort of the cab. When it’s time to relocate, the mast and its mounted FLIR cameras, radar, and sensors, stow out of sight for covert transportation.
-
Product
Rotating Dual Shaft Torque Sensors
RST SERIES
-
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
Product
Heavy Duty Dynamometers
MD-250-HD
-
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
Product
Eddy-Current Dynamometers
WB Series
-
Eddy-Current Brake Dynamometers (WB Series) are ideal for applications requiring high speeds and also when operating in the middle to high power range. Eddy-Current Brakes provide increasing torque as the speed increases, reaching peak torque at rated speed. The dynamometers have low inertia as a result of small rotor diameter. Brake cooling is provided by a water circulation system, which passes inside the stator to dissipate heat generated by the braking power. The water cooling in the WB provides high continuous power ratings (max. 140 kW). The WB dynamometers have accuracy ratings of 0.3% to 0.5% full scale ( 2% for WB 2.7), depending on size and system configuration. Additional options include: high-speed version, speed pickup, mechanical rotor blocking device, OEM version IS and vertical mounting.
-
Product
True RMS RF Millivoltmeter
3440A
-
The 3440A measures the true rms of low level RF and microwave signals to over 1GHz. High rms accuracy, traceable to NIST, is assured regardless of waveshape. Common calibration errors are eliminated through temperature compensation of the probe detector diodes; double shielding protects the interchangeable probes from rough handling and pickup. Relative gain or loss measurements are simplified by a 0 dB reference adjustment. DC output proportional to the ac input is provided for analog recorders and to allow operation as an ac-dc converter.
-
Product
Lock-In Voltage Preamplifier
SR550
-
Stanford Research Systems, Inc.
The SR550 Voltage Preamplifier is designed to work with any SRS lock-in amplifier. Preamplifiers provide gain close to the experimental detector, before the signal-to-noise ratio is permanently degraded by cable capacitance and pickup
-
Product
Optical Pick-up Sensor
-
TESCO has a pick up and disk sensors solution to meet your every need regardless of meter brand!
