Token Ring
-
Product
2 in 1 LAN Tester
PLTM20
-
Tests Pin Configuration for 10 Base-T, 10 Base-2, RJ45/RJ11, 356A, TIA-569A/568B and Token Ring CableRemotely Test Cables Up to 330 Yards AwayTest Ground WireMeasure DC/AC Voltage, DC/AC Current, Resistance, Continuity, and DiodeDC Voltage: Max Range 600 V, Accuracy +/- 0.5%AC Voltage: Max Range 600 V, Accuracy +/- 1.2%DC Current: Max Range 200 mA, Accuracy +/- 1.2%AC Current: Max Range 200 mA, Accuracy +/- 2.0%Resistance: Max Range 20 M, Accuracy +/- 0.8%Continuity Test: Beeps If Less Than 100 Accessories Included: Test Leads, LANtest Remote Terminator, 9V Battery, Carrying CaseDimensions: 6.38' H x 2.93' W x 1.73' DWeight: 10.86 oz.Sold as : Unit
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Lan Cable Tester
185 LCT
-
Standard Electric Works Co., Ltd
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable. The LAN cable tester can verify cable continuity, open, short circuit and miss-wired. The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels. Auto and manual scan functions. Ground wire test. Lock status function. Buzzer sound warning for wire status. Display : LED indication for wire status.
-
Product
Multi-Network Cable Tester
3PK-NT007N
-
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
Product
Mini Lan Cable Tester
MT-7058
-
Complies with CE safety standardAutomatically detect good connections, opens, crossed wires & split pairsTest RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cablePin to pin cable map indicatorNon-contact voltage detection for user safetyTraces wires with tone & remote lights allows one person operationCompact size and lightweight design for easy to carry aroundCircuit Protection for both units to ensure the testing qualityLow power consumption with auto power off function to preserve batteryLong cable test more than 300 meters
-
Product
Cable Tracer and Digital Multimeter
187 MCT
-
Standard Electric Works Co., Ltd
Lan Cable Tester● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.● The LAN cable tester can verify cable continuity, open, circuit and miss-wired. ● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan function.● Ground wire test.● Display : LED indication for wire status.Digital Multimeter● 4000 counts LCD.● Full automatic measurement. Voltage measurement. Resistor measurement.● Range change function.● Select function.● Data Hold function.● Continuity check.● Diode measurement.● Low battery indication.● Input impedance:10MΩ.
-
Product
Network Analyzer, Lan Tester, LED
72-6706
-
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc., By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit., Provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
Product
Multi-Modular Cable Tester
MT-7051N
-
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
Slip Ring Tester
-
The SRT is an automatic test system offering fast and accurate measurement and reporting of noise, contact resistance and insulation resistance. It’s been designed to improve QA for manufacturers of slip rings, commutators, rotary connectors. It can also be used to test devices coming back for repair and overhaul.
-
Product
Pancake Slip Ring
-
Pancake or Platter Slip Rings are a specialty for EVERAXIS USA. All drum style Slip Rings can be reconfigured into a Pancake design. Choosing one or the other is highly dependant on the geometric constraints of the system.
-
Product
Ring Disk Electrode
-
This ring-disk type electrode developed by NTT Advanced Technology Corporation is a form of printed electrodes. Users can choose them from Carbon, Gold and Platinum applied versions. Available as a working electrode of radial flow cells, achieves complete reduction/oxidation on the center disk at ultra-low flow rate because of its fine coulometric electrolysis efficiency. This also enables to analyze subsequent reaction as well as identification and quantitation of the sample at the same time.
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
Product
3-Component Quartz Force Rings
260 Series
-
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
-
Product
Capsule Slip Rings
-
Capsule Slip Rings are compact slip rings that can be used in a wide range of applications. They integrate rotor, stator, brush block, bearings and casings and enable the transmission of power and data through rotating systems. They are ready to be integrated into customers’ systems and provide built-in protection from humidity and dust.
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
Proving Ring
-
Morehouse Instrument Company Inc.
The Morehouse Digital Proving Ring reduces operator error and keeps the known stability of a Morehouse analog proving ring. Digital proving rings measure deflection of the ring in electronic "counts", rather than by a mechanical micrometer. This information can be interfaced to a computer, so data can be electronically logged, and the entire process can be automated programmatically. Calculations can be faster, with less operator action.
-
Product
Concentric Ring Set
PRF-911
-
- Measures surface resistance per ANSI/ESD STM11.11- Measures volume resistance per ANSI/ESD STM11.12- Meets the requirements of IEC 61340-2-3- Approximates surface & volume resistivity per ASTM D-257- Incorporates a spring loaded, self-aligning center electrode feature to reduce calibration frequency- Includes an insulated and metal dual test bed- Designed to work with a wide range resistance meter and one 5 lb. electrode- Certificate of calibration traceable to NIST included
-
Product
Induct-A-Ring Shaker Systems
T2000 Series
-
The T2000 Series of vibration test systems is designed to meet the ever-changing challenges of today’s moderate to extreme level test requirements. The T2000 Series is used by many different industries with a proven track record of unmatched and as yet unchallenged performance and long term reliability.
-
Product
Chip Rings
-
Panasonic Industrial Devices Sales Company of America
Extremely robust Chip Rings for signal measuring terminals featuring a metal sheet structure for high reliability.
-
Product
Quartz ICP® Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load. The through-hole mounting supports platform, integrated link, and support style installations using either a through-bolt or the supplied stud.
-
Product
Measuring Devices For Drawing Rings And Punches For 2-part Can Production
RINGMASTER - The Benchmark For Accuracy
-
Optik Elektronik Gerätetechnik GmbH
High-precision, non-contact measurement of inside and outside diameter, roundness (inside and outside) and concentricity of drawing rings for 2-piece can production. The Ringmaster sets standards in measuring accuracy, user friendliness and reliability and is therefore used in can factories on all continents.
-
Product
Schottky Barrier Ring Quads
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
Vacuum Slip Rings
-
Vacuum Slip Rings are especially suitable for a space environment on satellite platforms or payloads but can also be used in vacuum chambers of large ground-based scientific instruments such as synchrotrons or telescopes.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
Platinum Ring Electrode
PWE1
-
Manufactured from 99.99% high-purity platinum, these custom platinum electrodes are available in wire, coil, rod, ring, and salt-bridge configurations. Designed for electrochemical research, electrocatalysis, corrosion studies, sensor development, and battery testing, each electrode can be customized in diameter, length, geometry, and insulation material, with optional PTFE or PEEK housing and salt bridge assemblies.
-
Product
Through Bore Slip Rings
-
Through Bore Slip Rings are used in applications where the customer requires the bore space for some other capabilities (cooling or air media; optical or RF channels, etc.). The Slip Ring can be designed to accommodate a wide variety of bore sizes.
-
Product
Custom Pogo Pin Rings & Blocks
-
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
