Headers
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
1553 to Ethernet Converter
eNet-1553
Ethernet Interface
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
Product
XMC-to-PCI Express Adapter
4823
-
The Technobox, Inc. P/N 4823 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 1x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix Topology Without Column Protection Resistors
782385-07
Terminal Block
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Development System
FE-C450
-
* Emulates Dallas Semiconductors DS89C450 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
MAX31855 T-Type Thermocouple Sensor Breakout
SEN-30001-T
-
Breakout board for the MAX31855T digital thermocouple interface IC. Measured temperature range is -270C-400C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
SparkFun Atmospheric Sensor Breakout
BME280 (with Headers)
-
The SparkFun BME280 Atmospheric Sensor Breakout with Headers is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
-
Product
BME680 Environmental Sensor
28061
-
Raise your project’s environmental awareness with the BME680. The Bosch Sensortec BME680 Integrated Environmental Unit combines a gas sensor with air pressure, humidity, and ambient air temperature sensing functions within a single package for high performance air quality measurement. Parallax Inc. places the BME680 on a compact PCB with a 6-pin male header. This capable sensor does not have to be difficult to use. The BME680 is supported by BlocklyProp visual programming as well as C libraries for the Propeller multicore microcontroller. Code for other controllers is available from the Bosch Github repository.
-
Product
VTAC, Insert, Receiver/ITA, SIM, Pass-Thru, 8 Pos, 1 Slot
610151103
SIM Insert
VTAC, Insert, Receiver/ITA, SIM, Pass-Thru, 8 Pos, 1 Slot VTAC inserts are reversible and can be used as a Receiver or ITA insert.VPC's revolutionary high speed VTAC insert contains 8 gold-plated, self-aligning contacts and is designed to reduce crosstalk. With a data transfer rate of more than 12.5 Gbps per differential pair and a cycle life of over 150,000, VTAC has set the standard for high speed interconnect solution requirements. Sold in individual quantities.Use with VPC's right angle VTAC insert (p/n 610151104) or VPC's vertical header (p/n 610151107) to connect directly to a PCB.
-
Product
200 MS/sec RF/IF Rugged Portable Recorder
Talon RTR 2726A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight: just less than 30 pounds- Shock-and-vibration resistant SSDs perform well in vehicles, ships and aircraft- 200 MHz 16-bit A/Ds- 800 MHz 16-bit D/As- 80 MHz record and playback signal bandwidths- Recording & playback of IF signals up to 700 MHz- Real-time sustained recording rates of up to 3.2 GB/sec- Windows® workstation with high-performance Intel® processor- Up to 30.7 TB of SSD storage to NTFS RAID solid state disk arraySystemFlow® GUI with signal viewer analysis tool- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 18-36 VDC power supply
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-MF
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
PC/104 Digital Quadrature Encoder Input Board
104-QUAD-8
-
The 104-QUAD-8 card is a general purpose Quadrature Encoder Counter/Interface board. It is provided in the popular 104 format and conditions and monitors the outputs of 8 encoders. I/O connectors are right-angle 34-pin headers.
-
Product
6U VPX Power Interface Board VITA 62
106PIBC601-0000R
-
6U Convection Cooled VPX Power Interface Board, VITA62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
100 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
-
The 100 Pin 1.27mm Pitch Micro-D connector is used on many products to provide a high density 1A connector solution that is suitable for use to 150Vdc If you would like to develop your own cabling solutions, we offer mating connectors and connector hoods that allow you to create either your own cable based solutions, or a PCB header solution. Connector Blocks directly terminate the module connector and convert the connection to arrays of screw terminal blocks, or you can select to use a remote DIN rail mounted breakout to terminate the cables at the end of a cable assembly. You can also try our Cable Design Tool to graphically design a customized cable assembly.
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Board-to-FPC Connector for 5G Millimeter-Wave Antenna Modules
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Board-To-FPC Connector for 5G Millimeter-Wave Antenna Modules offer good SI/EMI/EMS characteristics for high-frequency applications and features our industry-leading Tough Contact construction that achieves high contact reliability and retention force. Tough against shock impact by misalignment, the fully-shielded structure in both socket and header significantly improves EMI characteristics necessary for RF applications such as 5G.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
64 Channel 12C GPIO Expansion
FXA-102 I2C Expander
-
The FXA-102 provides 64bit of General-Purpose Input / Output (GPIO) which are controlled via I2C. It is 3,3V and 5V compatible and based on four 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. Using the optional Phoenix Contact UMK housing, the FXA-102 can be installed on a DIN rail. The dual row 2,54mm pin headers allow usage with IDC20 connectors or wire wrap cables.
-
Product
Emulates Atmel T89C5111
FE-5111
-
* Emulates Atmel T89C5111 * 4K Code Memory * Real-Time Emulation and Trace * Frequency up to 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
-
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
Product
Board
Arduino Micro
-
The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
-
Product
Serial FPDP Rugged Rackmount Recorder
Talon RTR 2756
-
- Designed to operate under conditions of shock and vibration- Complete Serial FPDP record and playback system- Up to 8 I/O channels in a single 4U 19-inch rugged rackmount PC server chassis- Removable SSDs- Up to 38.4 terabytes of storage to NTFS RAID disk array- Copper, single-mode and multi-mode fiber interfaces available- Real-time aggregate recording rates of up to 5 GB/sec in eight-channel configuration- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- RAID levels of 0, 1, 5, 6, 10 and 50- Optional N+1 redundant power supply- SystemFlow® GUI virtual instrumentation panel for fast, intuitive operation- C-callable API for integration of recorder into applications- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor
-
Product
Low Cost Emulator
EB-XAG49
-
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
Micro Power, Header Insert, Receiver/ITA, SIM, Right Angle, 2 Pos, 2 Slot
510181103
SIM Insert
This header insert contains 2 right-angle micropower contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module.
-
Product
Ethernet Parallel Interface
Model 8013
-
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Development System
FE-51RD2
-
* Emulates Atmel AT89C51RD2, AT89C51ED2 and others * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-J
-
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
