Headers
-
Product
3U Conduction Cooled Power Interface Board, VITA 62
106PIBV301-0000R
-
3U Conduction Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
CB-50LP Low-Cost, Unshielded I/O Connector Block
777101-01
Terminal Block
50-Pin Male IDA to 50-Pin, Female Screw Terminal, Panel Mount Terminal Block - The CB-50LP provides 50 screw terminals for connection to I/O signals from 50-pin NI data acquisition devices. The CB-50LP includes one 50-pin header for direct connection to 50-pin cables and metal standoffs for use on a desktop or for mounting on a custom panel.
-
Product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
Terminal Block
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Emulates Winbond W78ERD2
FE-WRD2
-
* Emulates Winbond W78ERD2 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Arduino CAN Shield
IFB-10003-ANP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Eurorack Module Tester
TST
-
Test your modules safely without reaching into your case! The TST has two keyed 16-pin headers on the front of the module so you can plug and unplug quickly and easily. Two 16-pin plugs are included to shield the power pins when the module is not in use. It also has LEDs to indicate the power status on each rail.
-
Product
Arduino Shield Header Kit
INT-19002
-
Complete header set for Arduino Uno shields. Contains: 1 1x6, 2 1x8, 1 1x10, and 1 2x3 header. These headers have square pins and fit into standard 0.1" breadboards. Gold plated and RoHS compliant.
-
Product
Tool, Press Kit, i2 PCB Headers
910121199
Press Kit
Tool, Press Kit, i2 PCB HeadersAids in pressing fit pins into the header.
-
Product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts (610138200)
510150131
Receiver Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
TB-2676, Ribbon, 100 V, PXI Module Multiplexer Terminal Block
779535-01
Terminal Block
Ribbon, 100 V, PXI Module Multiplexer Terminal Block - The TB-2676 features ribbon cable headers that help you access all channels of the PXI-2576 Multiplexer Switch Module. You can use the TB-2676 to configure the 16 banks of 4x1 2-wire multiplexers included with the PXI-2576.
-
Product
Si1145 UV / Ambient Light / Proximity Sensor
SEN-36002
-
SEN-36002 is a highly integrated carrier board designed for the Si1145 UV, Ambient Light and Proximity sensor IC from Silicon Labs. This sensor has 100mLUX resolution, and has a dynamic range of 1 LUX to 128 kLUX with IR correction. This means that whether your application is indoors in poor lighting conditions or outside in full sunlight, this sensor has you covered. In addition, we added a high power LED (150mA max, 20 degree) to take full advantage of the proximity sensing capability of this IC - something you won't see on most competitive carrier boards. Integration is easy with 4 x 4-40 sized mounting holes at the corners of the PCB and signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. The INT pin is also broken out for interrupt capability.
-
Product
DIP Program Header
Series 675
-
DIP Program Headers. Aries DIP programmable headers offer unusual versatility for programming within the header itself. They can be individually programmed using cutters or Aries programming tool, Part No. T-675, available separately, to remove the interconnecting sections. Consult Data Sheet No. 22002 for Aries programming tool.
-
Product
Low Cost Emulator
EB-XAS3
-
* Emulates P51XAS3x Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 68-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
50-Pin Ribbon Breakout DIN Rail Mount
40-967-550-M
-
This accessory is designed to be used for terminating a 50-Pin ribbon cable connector. A 200-Pin to Quad 50-Pin ribbon header cable accessory is available that allows it to be used to terminate a 200-Pin connector. The accessory is suitable for mounting on DIN rails. The ribbon cable termination includes a strain relief.
-
Product
SparkFun Breadboard Power Supply 5V/3.3V
-
Here is a very simple breadboard power supply kit that takes power from a DC wall wart and outputs a selectable 5V or 3.3V regulated voltage. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled VCC and GND plug directly into the power lines. The lone pair of pins have no electrical connection but help support the PCB.
-
Product
Emulates AT89C5121 Derivatives with 6/12 Clocks/Cycle
FE-5121
-
* Emulates AT89C5121 Derivatives with 6/12 Clocks/Cycle * 16K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 16MHz/ 3V, 5V * X1 and X2 Mode Support * MS-Windows Debugger for C and Assembler * Keil mVision2 Debugger Compatible * PLCC-52 and SSOP-24 Emulation Headers * Serially Linked to PC at 115Kbaud
-
Product
NI TB-2646B Terminal Block for NI 2532B as 1-Wire Quad 4x32 or 2-Wire Dual 4×32 Matrix Matrix Topology Without Column Protection Resistors
782385-13
Terminal Block
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
1-, 10-, 40-Gigabit Ethernet Portable Recorder
Talon RTR 2735A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight, approximately 25 pounds- Shock- and vibration-resistant SSDs perform well in vehicles, ships and aircraft- Records gigabit, 10-gigabit or 40-gigabit Ethernet streams- TCP and UDP protocols- Copper or optical interfaces- Aggregate recording rates to 4.0 GB/sec- Windows® Server 2016 workstation with a high performance Intel® Core™ i7 processor- Up to 61 terabytes of SSD storage to NTFS RAID solid state disk array- Multiple RAID levels, including 0, 1, 5, and 6- SystemFlow® GUI with Signal Viewer analysis tool- C-callable API for integration of recorder into applications- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
Product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
-
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
Process Analyzer, Vent Master™ Series
-
Parkers Vent Master is designed to isolate the analyzer from fluctuating outlet pressures by controlling the pressure of the collection header and pumping the effluent sample gases into the fluctuating system
-
Product
Pin Converters
-
Blackhawk provides several different emulation pin converters to fit Texas Instruments standard JTAG target headers. This includes 14-pin TI, 20-pin cTi & ARM, 10-pin ARM, 60-pin XDS560 Trace and System Trace. All pin converters are available from the our Online Store or an authorized Blackhawk reseller.
-
Product
Universal LightProbe Sensor Six-Pack
S6P
-
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
Product
Power Interface Board 6U, 1 PSU connector
106PIBM601-0000R
-
The PIB 6U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 1m
40-971B-200-1m-MM
Cable Assembly
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
Cable Free ATE
CABLEFREEATE
test
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
QuadraPaddle 90 Series Modules
-
The versatility of VPC's QuadraPaddle twin female contacts provide four beams per end to ensure signal integrity from instrumentation to the Unit Under Test (UUT).Twin male contacts interconnect to ribbon cable, headers, and other standard connectors.Makes system configuration a simple “plug & play” operation and delivers high density, high performance interconnectivity at a lower cost per point.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
SparkFun TRRS 3.5mm Jack Breakout
-
TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for "Tip, Ring, Ring, Sleeve," which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground. Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players). This breakout board makes it easy to add a TRRS jack to your prototype or project by breaking out each conductor to a standard 0.1" spaced header.
-
Product
Digital Cable
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
