Test Boards
See Also: Board Test, Testboards, DUT, Extender Boards
-
Product
Extender Boards
-
VECTOR Electronics and Technology, Inc.
Extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged. This provides access to both sides of the test board.
-
Product
ASA240
-
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
In-Circuit Test Systems
-
Keysight offers leading board test solutions for electronics manufacturers to tackle a wide range of PCBA test access and coverage issues for today's complex printed circuit assemblies.
-
Product
High-Speed Embedded Host Electrical Test Board
HSEHET
-
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
ICD 3 Test Interface Module
AC164113
-
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
Product
Repeat Durability Tester
TIQ1000
-
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
Product
Accelerated Stress Test Chamber
-
CSZ's accelerated stress test chambers combine mechanical refrigeration; LN2 cooling and high velocity air flow for fast product temperature change rates. Chambers are typically designed with a change rate up to 30C (54F) per minute based upon the part temperature. Common uses are production stress testing circuit boards, electronic drives, assemblies, etc. Design allows the user to quickly control and change the temperature of the product.
-
Product
Test Board For QSFP+ Transceiver
EQSFP10
-
The OPTELLENT EQSFP10 is a cost-effective and convenient test board for testing QSFP/QSFP+ optical transceivers in R&D and manufacturing environments. The EQSFP10 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP10 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Generic Probe Cards, PIB's, and Loadboards
-
Test Spectrum can provide generic Probe Cards, Probe Interface Boards (PIB), and loadboards. Choose from existing configurations already designed, or a generic test board for your specific tester configuration can be designed quickly.Teradyne J750 Probe Card and PIB; Teradyne Integra Flex PIB; Teradyne Ultra Flex PIB; Teradyne Catalyst PIB; Credence Quartet PIB (Probe Interface Board); Advantest 93K 1024 PIB
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
Step Probes (F732SP) F73216B1014G150SP
1006278
-
The Step Probes (F732SP) F73216B1014G150SP offers a highly reliable measurement solution designed for specialized electronic applications. With a pitch of 2.54 mm and a temperature range of -45°C to +100°C, these step probes ensure optimal performance across a broad spectrum of environments. Whether you are testing circuit boards or conducting R&D, their impressive specifications guarantee precision and efficiency.
-
Product
Chassis Platform Accessories
-
Embedded Computing Systems require more than just a chassis housing with backplane, power supply, cooling and payload boards. To complement our wide range of systems, Elma offers a comprehensive range of system level accessories, including I/O solutions, HMI displays, system/power management controllers and test & development boards.
-
Product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
-
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
Product
Test Adapter / Extender
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
Semi-automatic Three-phase kWh Meter Test Bench
SY8310
-
Hong Kong Songyang Industrial Ltd.
The new SY8310 series semi-automatic three phase energy meter test board, designed according to International Standard, is a newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
Product
FMC Loopback Test Board
-
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
Product
Calibration Pulse Processor
2401
-
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
Product
Meter Test Board
MTB-3200
-
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
Product
Semi-automatic Single Phase Close Link kWh Meter Test Bench
SY8120
-
Hong Kong Songyang Industrial Ltd.
The SY8120 new series semi-automatic single phase energy meter test board, designed according to International Standard, is newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
Product
K-Base Test Board Adapter
1180
-
The TESCO K-Base Test Board Adapter allow quick, convenient testing of self-contained K-Base meters on test boards designed for socket type meters. The K-Base Test Board Adapters are designed for single phase (Catalog No. 1180-2) and polyphase (Catalog No. 1180-4).
-
Product
Cardboard Puncture Tester
DRK104A
-
Shandong Drick Instruments Co., Ltd.
DRK104A cardboard puncture tester is used to test the corrugated board anti-pierced performance (puncture strength). It has the snap-operating handle, automatic reset and safety protection function. It is the indispensable instrument for carton manufacturing plants, research and quality supervision, inspection and other enterprises and departments.
-
Product
Functional Test
-
Functional test systems offer users the ability to test boards in a real world environment, checking that they function as designed by stimulating inputs and monitoring outputs. Often whole suites of boards have similar functions and this is where a generic functional tester offers large benefits over more bespoke solutions.
-
Product
Meter Test Board
MTB
-
The accuracy of TESCO’s Meter Test Board (MTB-3050) is now available in multi-position test boards to perform individual or simultaneous accuracy tests in the meter shop!
-
Product
Kelvin Test Contactor
nano
-
nano Kelvin™ test contactor is a well-established Cantilever Kelvin test contactor with proven performance in the automotive market and further increasing popularity due to the robustness and reliability of the product.Featuring a small imprint area, contact motion decoupled from the test board and simple and cost-efficient test boards.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
A-Base Test Board Adapter
1182 and 1183
-
From time to time, you may find yourself needing to test A-Base meters. Or perhaps you will need to test them for the first time in years as part of a removal project. Well, TESCO can help with the A-Base Test Board Adapter!
-
Product
Debug Fixture
-
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
