Host
-
Product
Wide Temperature Range HDR USB3.1 Gen1 Camera Board (Color)
See3CAM_CU20
-
See3CAM_CU20 is a 2.0 MP HDR USB camera board with ultra-Lowlight performance. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). This Full HD USB3.1 Gen1(5Gb/Sec.) camera is based on 1/2.7" AR0230AT CMOS digital image sensor with a pixel size of 3.0 μm x 3.0 μm from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows, Linux. This HDR camera is also backward compatible with USB 2.0 host ports.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Protocol Analyzer
USB Explorer 200
-
The USB Explorer 200 is a non-intrusive high speed USB 2.0 protocol analyzer that enables you to display bus states, packets sent and decode descriptors of the USB protocol. It can detect errors in devices, host controllers, embedded softwares or drivers as well as measure their performance.
-
Product
Digital I/O PCI Card
GC5050
-
The GC5050 is a high speed Dynamic Digital I/O card that provides capabilities comparable to high speed I/O products found in large functional test systems. The card shares an identical architecture with the GX5050, a 6U PXI card. Both have the ability to operate independently of the host computer when in the RUN mode.
-
Product
6U Dual 64/100 PMC VME Carrier
V2PMC2
-
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
Product
PXIe Remote Control Interface Module
43-921-002
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
*OEM Power Sensors
-
The OEM “standard” sensors are actually families of existing OEM sensors with typical specifications shown. They can be tailored as needed to fit your specific requirements. In addition to the products described, Ophir has developed hundreds of other OEM solutions. These compact laser power sensors have built-in amplifiers and are easy to install. They contain all the electronics needed including algorithms to increase the sensor's speed of response. Connections to the sensors are simple, with the host providing DC power and the sensor providing a voltage or digital output. Outputs Available: DB15 smart sensor output; Calibrated analog output; RS232; USB; Ehthernet. Simply fill out the Sensor Customization form so we can provide just the right solution for your needs.
-
Product
PCIe Gen3 Module For PCIe Bus Expansion
PCI123
-
The PCI123 is VadaTech’s 3rd generation PCIe expansion module based on the PCI-SIG specification. The board is a high-speed bridge from the host PCIe bus to VadaTech’s UTC006 PCIe Gen 3 x16 MCH.
-
Product
Quad Port Copper 10GBase-T Ethernet PCI Express Server Adapter With Intel® XL710-BM1. Ideal For Enterprise Network Infrastructure.
PCIE-2231NP
Network Interface Card (NIC)
Intel® XL710 Controller4 10GbE Base-T (RJ45) portsPCIe Gen.3 x8 host interfaceLow profile (half length) form factorsSupports SR-IOV based virtualization
-
Product
Cylindrical Inductive Proximity Sensor (Built-In Amplifier)
GX-300
-
Panasonic Industrial Devices Sales Company of America
The GX-300 Series of Cylindrical Inductive Proximity Sensors provide state-of-the-art features, enhanced basic performance, improved operability, and an extensive model lineup including IO-Link compatible models that are capable of transmitting sensor data and status information to a host controller through an IO-Link master.
-
Product
4G Router
BB-SR31000420
Router
SmartFlex, Global, 3x Ethernet, 1x RS232, 1x RS485, Metal, Without Accessories. Global LTE Cat.4 high speed connectivity with 3G fallback, 2× SIM. LTE B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
cRIO-9039, 1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 8-Slot CompactRIO Controller
783851-01
Embedded Controller
1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 8-Slot CompactRIO Controller - The cRIO-9039 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. Additionally, the cRIO-9039 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
4 Digit Temperature Meter (5 Channels)
CM1-TX5
-
RS-485 Modbus RTU protocol (with communication LED indicator)RS-485 address 1~255Communication Baudrate 9600, 19200, 38400, 57600, 115.2KParity check N81, N82, E81, O81Input 5 channels of signal selectable：thermocouple/PT100.5 channels of input can be set to play 1~10 seconds loop display.1~5 channels of display value limits can be set, and the number of channels of carousel display screens can be set by yourself.5 channels of input signals with LED unit cycle display.Standard 2 groups of alarms Hi, LO with communication LED indicators to ensure the normal operation of the field system.Suitable for HVAC refrigeration and air conditioning PLC, DDC, PC brands to achieve remote real-time monitoringCan be used in solar panels, medical control, clean room, ice water host, boiler, motor, chemical plant, power plant, school energy-saving control, remote control of power monitoring panel
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 5 Channels, 2.5 GS/s on 10 Channels, 1.25 GS/s on 20 Channels
DN6.225-20
Digitizer
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
4 MP OV4682 RGB IR Camera Module
e-CAM40_CUMI4682_MOD
-
The e-CAM40_CUMI4682_MOD is a 4 MP RAW RGB-IR MIPI OV4682 camera module with the M12 S-mount lens holder. The e-CAM40_CUMI4682_MOD RGB IR camera module is based on OmniVision's OV4682 1/3" Optical format CMOS Image sensor, that captures high-resolution images and videos as well as IR information. Its dual RGB-IR Camera capabilities allow it to bring a host of additional features to machine vision applications and by combining RGB - IR in a single camera module reduces the total cost and saves space. Customers can evaluate e-CAM40_CUMI4682_MOD with See3CAM_CU40 over USB 3.0 interface and e-CAM40_CUTK1 over MIPI interface. e-CAM40_CUMI4682_MOD camera module can stream the 4MP(2688x1520) unprocessed 10-bit RAW data video upto 40 fps.
-
Product
cDAQ-9178, 8‑Slot, USB CompactDAQ Chassis
781156-01
Chassis
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Product
Compact PCI
cPCI2IP
-
The cPCI [Compact PCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots.
-
Product
Digital Signal Processor
HSR40 CC
-
Curtiss-Wright Defense Solutions
Curtiss-Wright’s CHAMP-XD2 digital signal processor (DSP) card handles the incoming data and features two multi-core Xeon D processors and two built-in 40 GbE interfaces. The processor hosts a Linux operating system and runs the HSR40 data recording and storing application. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data.
-
Product
Test Database Software Module
-
The relational test database is the pivotal point of the software structure. On one hand, this is where the test applications and test systems used for productive testing are stored; on the other hand, it provides the storage space for all DUT-related test data. Depending on customer requirements, the test database may either be hosted locally on the test system or centrally on a server, supporting several test systems. The database performance is sufficient for a high-volume production environment with many test systems which access the central database in parallel. LXinstruments prefers to implement the database as a license-free MySQL database; it is however also possible to realize a version based on Microsoft SQL.
-
Product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
-
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Low Light USB Camera With Microphone
Conversa
-
Conversa, camera for conversation (See3CAM_CU38), is a 3.4 MP low light USB 3.1 Gen1 camera with built-in stereo microphone providing 16bit audio @48KHz. This low-light USB camera is the next advanced version of our flagship product See3CAM_CU30, with built-in stereo microphone for crystal clear sound. It is a plug-and-play (UVC and UAC) compliant USB 3.1 Gen1 SuperSpeed camera and is also backward compatible with USB 2.0 host ports. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It has a dedicated, high-performance Image Signal Processor chip (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control).
-
Product
Emissions Dynamometers
MD-1000-M
-
The MD-1000 sets the industry standard for heavy duty chassis dynamometers due to its rugged design and accurate loading capabilities. Simulate on-highway driving conditions under real world loads. Adjust loading to simulate a host of in-use operating conditions. The 1000 is approved for use in Nevada and Colorado for Diesel Smog Testing.
-
Product
Power Special Test Equipment
PSTE
-
AMETEK Programmable Power, Inc.
There are several key benefits of the PSTE. First, it is a complete turnkey system that is capable of operating locally through a simple GUI interface or remotely via a host computer as a single Ethernet address. The spacecraft engineer who defines the spacecraft power bus limits, cabling scheme, mode simultaneity matrix, and system behavior based upon limit conditions implements the real intelligence of the system. From this definition, operating procedures can be generated to allow spacecraft technicians to operate the system, system protections are implemented that perform cable detection and mode verification, automated spacecraft fixture identification and related mode capability, and more.
-
Product
Titration
Titrando
-
Titrando titrators have been developed to meet exacting titration demands. These titrators come with a wide range of security and traceability options, making them particularly suitable for use in regulated industries. Titrandos are capable of performing all common titration types and offer a host of automation and control options.
-
Product
Lasers
-
Alnair Laboratories Corporation
A narrow-linewidth wavelength tunable laser source for applications such as coherent communication and long-range optical sensing. The laser can be locked to ITU grid wavelengths and fine-tunable with 1 MHz resolution. The laser can be controlled on the front panel or remotely via USB/GPIB. Benchtop version can host up to 4 separate lasers, with a combination of C- or L- band tunable laser.
-
Product
2MP Stereo Camera for NVIDIA® Jetson Nano™/AGX Xavier™/TX2
STEEReoCAM™
-
Houses two OmniVision's 1/2.9" OV2311 Monochrome image sensorHigh-speed 2-lane MIPI CSI-2 interface to connect with the Host ProcessorPlugs in to NVIDIA® Jetson Nano™/AGX Xavier™/TX2 developer kit2MP Global Shutter Sensor10-bit Monochrome output formatHouses 6-axis Inertial Measurement Unit (IMU)Baseline distance of 100mmAccurate depth sensing with a flexible range between 0.95m to 8mS-mount lens holder (M12) with pre-calibrated S-mount lens pairSupport Multiple SteereoCam to a Single board
-
Product
cRIO-9034, 1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 4-Slot CompactRIO Controller
783453-01
Embedded Controller
1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 4-Slot CompactRIO Controller - The cRIO-9034 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. Additionally, the cRIO-9034 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
General Noise & Vibration
-
NVGate, the software platform is the cornerstone for all measurement tasks. It hosts the suite of OROS software modules. Whatever the application and software module, it allows you working in a coherent and continuous environment.
-
Product
NVM Express
-
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
