Shielded Cables
See Also: Cable Testers
-
product
CAT-5 Cable Equalizers
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Cable Testing Service
Cable testing service available from Cimbian includes:Helping you with the test specificationBuilding the test interface, where necessaryCreating the test programBarcodingTest reportsSimple continuity testingMeasurement/verification of resistances and diodes (traceable to national standards)Hi-Pot testing to 1500VDC / 1000VAC
-
product
Micro Coax, Contact, Receiver, RG316 Double Shield
610140104
Primary mating contact 610141104. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor – SolderShield – SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 10.5 GHzVSWR 1.0225 +.05 f(GHz)Insertion Loss -√f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Custom Cable Assemblies
AMETEK Power Instruments has designed and manufactured electrical, thermocouple, and fiber optic harness assemblies for more than sixty years. We have the experience and capability to produce rigid and flexible harness assemblies for virtually any application, whether it is a missile ignition assembly, aircraft actuator assembly or a thermocouple harness for an industrial gas turbine. AMETEK Cable & Harness Products boast superior reliability, high temperature operation, numerous braiding options for abrasion resistance and EMI shielding, waterproof or environmentally sealed, and custom molding. For more information, please contact us.
-
product
A-quad-B cable
E1735A-001
The A-quad-B cable is a 3-meter cable that connects your machine's A-quad-B encoder output to the E1735A USB axis module's A-quad-B input connector. The cable is supplied with a mating connector for the USB axis module on one end. The other end is un-terminated, allowing you to make the connections you need for use with your machine's encoder.
-
product
Flexible Cable Assembly
WCBA-WC0129M.29M1
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
50Ω UWave SMA Cable Assembly, 26.5GHz, 0.25m
40-977-542-0.25m
50 Ohm uWave SMA Plug to uWave SMA Plug Cable Assy, 26.5GHz, 0.25m Long.
-
product
Network Cable Tester
PHCT45
This Pyle network cable tester checks RJ45 and BNC network cables for continuity and correct polarity. LEDs show the status of each pin. , perfect for the IT guy on the go.
-
product
Cable Length Meters
CLM-1000E
*Measures these metric wiresizes: 0.75, 1, 1.5, 2.5, 4, 6, 10, 16, 25, 35, 50, 70, 95,120, 150, 185, 240, 300, 400,500 mm2*Eight user-programmable settings for other sizes*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Meters
-
product
Cable Assembly, Receiver, 36", QuadraPaddle, 160 Pin Female DIN
540069010229
Cable Assembly, Receiver, 36", QuadraPaddle, 160 Pin Female DIN.
-
product
10 Ft Shielded Cable For 5xxx/35xx Products (68 Pin)
GT95028
10 ft shielded cable for 5xxx/35xx products (68 Pin)
-
product
Lan CAble Testers
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
product
18" Cable
CONV1553-5
An 18" cable assembly transitions from an IP-708 Module ribbon connector on the VXI-AIC to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends.
-
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Spring Latch
A068SMR-T-5B100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Cable & Antenna Analyzers
Site engineers and technicians have been using sweep testers also known as cable and antenna analyzers to validate installations or to find trouble locations and imperfections in wireless sites.
-
product
ITA, I2 Micro ICon, Wired, QuadraPaddle, 36", Flying Leads
410130409
ITA, i2 Micro iCon, Wired, QuadraPaddle, 36", Flying Leads This i2 Micro iCon comes wired with a flying leads cable assembly containing 168 QuadraPaddle patchcords with 24 AWG PVC.
-
product
RF Shielded Test Enclosure, for Laptop Testing
JRE 2218
Breeze through laptop RFI and wireless tests with the 'bigger than-a-breadbox' 2218! Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan.
-
product
Standard Round 2m Cables, Shielded, for Higher Current
ST010-S
Connection to digital boards, intended for higher currents. to be used with CPCI-1500, APCI-1500, APCI-1564, APCI-2032.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m HV, Exit Away From Pin 1
40-972-050-0.5m-MU-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Ethernet Cable Emulator
Upon different commands, it can simulate different network cable lengths, including 3 Modes: Bypass, Short, 100M. It can be used independently or jointly with other devices.
-
product
Cable Assembly, Receiver, Mini Coax, 20", 20 SMB Plugs
540075010109
Cable Assembly, Receiver, Mini Coax, 20", 20 SMB Plugs
-
product
Audio Cable Testers
AudioJog Pro 5
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
-
product
Cable Assembly, 50-Pin D-Type, Male to Male, 0.5m HV, Exit Towards Pin 1
A050DM5-050DM5-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock.
-
product
Pipeline & Cable Locator
STC-PCL 1101
Shanghai Stone Communication tech Co., Ltd
STC-PCL1101 Pipeline & Cable Locator consists of a Transmitter and a Receiver, used in the underground utilities route locating, the depth measuring and long distance tracing. We adopted multicoil electromagnetism technology on this Pipeline & Cable Locator, enhanced the pipeline localization to decide the depth precision and the goal pipeline recognition capability, also could accurately carry on tracing and the localization in the pipeline crowded complex region to the goal pipeline. Thus it is widely used in the telecommunication, electric, tap water, natural gas, physical prospecting, town planning and so on.. STC-PCL1101 has many optional accessories, thus increased their use, and expanded their application scope.
-
product
Cable Avoidance Tool
CXL3
The CXL3 is a robust and affordable analogue industry standard ‘pick-up-and-go’ Cable Avoidance Tool used to detect pipes and cables prior to excavations. Designed for use with an SGA3 Signal Generator.
-
product
Ribbon Cable Tester
RibbonJoG mkII
The RibbonJoG Cable Tester is a versatile ribbon cable tester. It allows the user to either identify a correctly made standard ribbon cable, or carry out rapid comparison tests having stored known good cable details
-
product
50 Ohm SMB to SMB Cable Assembly
40-977-511-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
