Motor Rotation
See Also: Motor Rotation Testers, Tachometers, Phase Rotation
-
Product
Pump & Motor Testing Instruments
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump and Motor Testing Instruments - dynanometer, stator rotation direction detector, digital RPM meter, DC power analyzer, motor analyzer.
-
Product
Linear Motor Tester Lite
BK2019B
-
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
Product
Rotation Meters
-
Here you will find many types of rotation meter. There are different ways of measuring revolutions within the industrial sector, either optically or mechanically. The PCE-151 handheld series of rotation meter with Rotation Meter OverviewRS-232 interface can measure revolutions and velocity and store the readings onto a computer using software which comes with the device. The handheld digital rotation meter is ideal for measuring velocity and revolutions in research and maintenance. The PCE-T236 rotation meter measures velocity both by contact and non-contact and is good value for money.Non-contact measurement of velocity is done with the help of reflective tape. For a device that can be installed for measurements over a period of time, we recommend the PAX I rotation meter.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 4.0 W250 | VP 210157
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans, and with high vehicle throughput and increased loads.
-
Product
Motor Stator Tester
DZ900
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of y-type three-phase motors.
-
Product
Single channel Motor Insulation Monitor
-
The SURETECH Motor Insulation Monitor measures insulation resistance to earth of electric motors when themotor stops. Motors running from mains (380 / 220V) and higher voltages up to 6.6kV can have their insulationcontinuously monitored.
-
Product
Motor Testing Panel
VMTP
-
It covers No Load Test, Full Load Test, Block Rotor Test, Temperature Rise Test, Reduce Voltage Test, Pull Up Test, Momentary Over load Test for 3-Phase & 1-Phase Motor. It measures Voltage, Current, Power, Apparent Power, Reactive Power, Power Factor (PF), Frequency, RPM, Corrected RPM, %Slip, Torque with correction, Output Power, Efficiency of Motor.
-
Product
Motor Exhaust Gas Analyzer
MEXA-ONE
-
MEXA-ONE offers an intuitive user interface with a highly efficient hardware and software design.This results in increased testing efficiency and economical facility operation, while enhancing reliability and accuracy. These advancements are possible because the MEXA-ONE software employs new "HORIBA ONE PLATFORM". This platform integrates the test devices in an emission cell into a single user interface, increasing efficiency and optimizing user control over the entire testing process.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Motor Performance Tester
CT Series
-
Shanghai Aoboor Electric Co., Ltd.
Test the cogging torque of motors, separate motor cogging torque and friction torque accurately; cogging torque test results is independent of test speed and speed fluctuation.
-
Product
Motorized Force & Torque Measurement Test Stands
-
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
Socket Wrench Torque Sensor Rotating Type
RSS SERIES
-
Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.
-
Product
Motor Starting & Control Resistors
-
Motor Starting Resistors are used to reduce the voltage at the motor terminals and also decrease the starting current. Motor Starting Resistors are necessary because the self resistance of a motor armature is very low. When the voltage is first applied, excessive current will flow. For limiting this current, since there will be no resisting back electromotive force (emf),some series resistance can be added to the armature windings.
-
Product
Turret Integrated Rotating Systems (OMFV)
-
Slip Rings can be fitted on tank turrets and military vehicles for frontline operations, allowing power, Ethernet, video and CAN bus signals to be transmitted on the battlefield using fiber optic channels.
-
Product
Brushless/Servo/Stepper Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
Product
Stepper Motor Controller for CompactPCI
CPCI321
-
The CPCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
Multi Channel Linear Vibration Motor Aging Tester
BK8018
-
The BK8018B is our biggest Aging Tester for linear vibration motors. Connect up to 20 DUT's and the system will automatically test them all simultaneously. As well as evaluating current, it can also connect to accelerometers to test vibration characteristics. You can see information on the monitor in real time, and also store it to analyze later so you can keep track of the accuracy and stability of your manufacturing process. In addition, we will modify BaKo’s BS1123-BS8018 program to fit your needs so that the testing you do is a custom fit.
-
Product
Digital Motorized BRINELL Hardness Tester
900-355
-
Load Cell driven system provides precise control of test force application Direct digital reading Engineered to obtain highly sensitive and accurate readings Perfect for laboratories, workshops, tool rooms, inspection labs, etc. Measuring Range: 8-650HBW
-
Product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
-
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
Product
Stepper Motor ,High-Precision Linear Stages,Application for Industry
KSAXXX-13-X
-
Model: KSAXXX-13-XStepper Motor ,High-Precision Linear Stages,Application for Industry
-
Product
DC Motor Trainer
-
We hold expertise in offering wide range of DC Motor Trainer that is manufactured using advanced technologies and modern amenities. Our product range ensures high configuration DC Motor Dynamometer trainer & DC Motor Eddy brake trainer. They have high strength and are thermostatically balanced. DC Motor Trainer is offered at most affordable rates.
-
Product
Motorized Test Stands
-
The Chatillon motorized test stands are optimized for production floor operation.
-
Product
High & Low Temperature Impact System for ATF Cooling Motor
EVTP-30
-
Shanghai Dean Electrical Co., Ltd
This test system provides the most direct life evaluation of ATF cooling based EV motor by simulating the temperature impact from ultimate self- heating of the motor and severe cold condition from environment.
-
Product
Motors
-
When your application demands ultra-precise positioning and high throughput, trust Aerotech’s motor expertise.
-
-
Product
Rotational Viscometer
LD-LRV-A10
-
Labodam LD-LRV-A10 Rotational Viscometer has a wide range of application in the market. It is designed with advanced manufacturing technique.
-
Product
Motorized Constant Loader
CLE-150 Series
-
When we measure the hardness of rubber test specimen etc. with durometer, we have the possibility to make an error for the result of the measurement. To make solution for such an important factor fo the error, CLE-150 Series is employed the motor driving system for the descent speed control, and then we could realize to measure the hardness of constant speed and constant pressure that is precise and reproducible.
-
Product
Brushless DC Motor Drivers
-
ST’s STSPIN drivers for 3-phase brushless DC (BLDC) motors includes power drivers in a 3-phase bridge configuration and integrated solutions with built-in decoding logic for Hall-effect sensors.
-
Product
Rotating Telemetry Systems
2100B Series
-
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
