Light Sources
See Also: Lighting, Optical Light Sources, LED Sources, Light Choppers, Opacity, Spectroradiometers
-
product
High Power Programmable AC Source
Chroma Systems Solutions, Inc.
Simulate various AC line input conditions and measurement of critical characteristics for products under test
-
product
AGS Energy Source
Teledyne Marine AG Geophysical Products
Source firing systems for sealed electrical interconnect where high shock and mechanical survivability is paramount.
-
product
Low Light Imagers for Defense
Teledyne Imaging addresses low light imaging applications with a range of standard CMOS and EMCCD image sensors suitable for defense and security surveillance systems, whether for battlefield, vehicle, airborne, CCTV or security day camera’s.
-
product
Three-Pole Lighting And Surge Arrestor
PIVM12,5-275/3+0 Vseries
PIVM12,5-275/3+0 Vseries is a three-pole lightning and surge arrester Type 1+2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of both, the lightning current and the switching surge, which are generated in power supply systems entering the building. The use of the lightning current arresters PIVM12,5-275/3+0 Vseries is mainly in the power supply lines, which are operated as TN-C system. The main use of PIVM12,5-275/3+0 Vseries arrester is in structures of LPL III – IV according to EN 62305 ed.2. The marking M specifies a type of construction with removable module.
-
product
Light I-V Testing for Modules
FMT-500
Advanced analysis of solar modules including light I-V and Suns-Voc data. Capability to accurately measure high-efficiency modules.
-
product
Light Meters For Photometry
Comprehensive range of solutions for the measurement of illuminance (lux), luminance (cd/m²), luminous flux (lumens) and luminous intensity (cd).
-
product
Light and Energy Meter
Model 656
OAI Model 656 Meter is designed for use with all mask aligners and flood exposure systems. For over 45 years, OAI is a world leader in UV Light & Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries.
-
product
Voltage Tester, 12V to 1000V, Light
72-2980
Non-Contact Voltage Detector Handy accessory detects presence of AC voltage from 12V ~ 1KV, providing clear audio and visual indication. Five segment bargraph display shows relative voltage level. Built in LED flashlight provides added convenience in poorly lit environments.
-
product
Multichannel Source Measurement Unit
AXS7720
Extremely low noise with linear output stageVery fast rise and fall timesProgrammable current pulseIntegrated current measurement unitIntegrated voltage measurement unit
-
product
Light Shaping
VirtualLab Fusion supports light shaping by freeform surfaces, diffractive beam splitters and pattern generators, diffusers, and general arrays of micro-optical components, including, but not limited to, micro-lens arrays.
-
product
Precision DC Source Instrumentation
High power, dual channel PXI User Power Supplies as well as precision DC source instrumentation. These products are offered in both PXI and GTXI formats.
-
product
Tower Light Monitor
1750-TLM
Designed with the Broadcaster in mind the 1750-TLM provides built in flexibility to simplify even the most complicated installations. It can even alarm for single bulb failures on towers with Beacons and Obstruction lights on a single circuit. Status oututs eliminate the worry of operator interpretation and provide definitive Good-Bad indications for the operator and your logging equipment. Don’t let tower light failures expose you to increased liability, the 1750-TLM is compatible with most existing control equipment and may well provide your best return on investment this year!
-
product
Multi-Angle Light Scattering Detector
PN3621
Since the 1990s Postnova has been a leading innovator and developer of special advanced online Light Scattering solutions for coupling with chromatographic separation systems. The first model was the PD2000 - Static Light Scattering detector for coupling with Asymmetric Flow FFF. Later on the models PN3020 SLS and PN3070 MALS have been launched. Based on these over two decades of practical experience, Postnova has collected a unique competence in the area of Laser Light Scattering and has developed the unique PN3621 MALS - Multi-Angle Light Scattering detector series. The model PN3621 MALS is a completely new type of high performance MALS detector system with a unique range of specifications.
-
-
-
product
Ada Source Code Analyzer
CodePeer
CodePeer is an Ada source code analyzer that detects run-time and logic errors. It assesses potential bugs before program execution, serving as an automated peer reviewer, helping to find errors efficiently and early in the development life-cycle. It can also be used to perform impact analysis when introducing changes to the existing code, as well as helping vulnerability analysis. Using control-flow, data-flow, and other advanced static analysis techniques, CodePeer detects errors that would otherwise only be found through labor-intensive debugging.
-
product
Light Meter
LI-250A
The LI-250A is a portable meter that displays the output from any LI-COR light sensor that has a cable terminated with a BNC connector. It shows instantaneous values or 15-second averages of values from a sensor.
-
product
Source of Signals
CRS+
The CRS+ is a stable and calibrated source of signals which cover the 9KHz - 30MHz frequency range. The fundamental signal is a 15KHz comb and each harmonic is output as a narrowband peak of known amplitude. This signal is output on either the L and N lines, referenced to ground. A switch provides on/off and line selection.
-
product
AC Power Source
LSP-500VAR
• AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCU • Protection for over hot, thundering voltage and current • Total voltage distortion: ≤0.3%; Voltage stability: ≤0.05%/30min • Load adjust rate: ≤0.05%; Frequency stability: ≤0.01%/30min • Output voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400Hz • It is pure sine wave AC power source with low harmonic and high accuracy • Input Power: 220V and 50/60Hz (110V can be option) • Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
product
Single Filament Sources
Get a cost-effective solution that’s ideal for your high-volume, high-value MBE process needs with reliable Veeco Single Filament Sources. They feature dependable band thermocouples and single heater filaments for 750-1200°C operation. Three system configurations, and many crucible sizes, are available. All offer stable and consistent fluxes of high vapor pressure materials.
-
product
Excitation Sources
SPECS Surface Nano Analysis GmbH
o our customers in research and industry we offer a variety of sources for deposition, excitation and charge neutralization as well as analyzers and monochromators. Most of our sources originate from product lines which we have taken over from Leybold AG, Cologne, and from VSI GmbH. The X-ray monochromator Focus 500 and the UV monochromator TMM 302 are original developments by SPECS.
-
product
Long Life Serismic Energy Source
2800LLX
Bolt introduced the LONG-LIFE air gun in 1992. Since then it has become the standard energy source for marine seismic exploration.
-
product
6000 Series ATE（AC Source）
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
product
SparkFun Ambient Light Sensor Breakout
TEMT6000
Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin.
-
product
SpikeSafe DC / Continuous Pulsed Current Sources
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
-
product
Light Meters For LEDs
Photometers for the measurement of visible LEDs and radiometers for UV , visible and NIR LEDs.
-
product
Exclusive Control Unit For Safety Light Curtain
SF-C10
Panasonic Industrial Devices Sales Company of America
Exclusive Control Unit For Safety Light Curtain
-
product
Omnidirectional Source
BAS001
The BAS001 Source is designed to generate omnidirectional sound fields for making standard compliant measurements including: reverberation time (ISO 3382, ASTM E2235), building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-4 ISO 140-3, ASTM E336, ASTM E90, DIN 55 210). The BAS001 is typically used to saturate a room with a uniform acoustic field. The available high-efficiency power amplifier has no fan for cooling, allowing measurements in quiet environments, like those in reverberation time applications.
-
product
*Divergent Light Measurement
The IS1.5-VIS-FPD-800 & IS1.5-IRG-FPD-800 contain 2 photodiodes: a calibrated photodiode for precise power measurement using Ophir meters and a fast photodiode with integral reverse bias circuit for temporal characterization using third-party instrumentation such as oscilloscopes and spectrum analyzers. Their small, 1.5" internal diameter preserves the temporal shape of pulses down to 3.5 nsec for VIS and 6 nsec for IRG. An SMA fiber optic connector is provided for connection to a spectrometer. The large, 20 mm input aperture allows for wide acceptance angles and long working distances, making these spheres well suited for testing VCSELs and other types of laser.
-
product
Visible Laser Source
VLS35
The KD Optics VLS-35 is a pocket sized, visible source used for testing fibre optic cable installations. The unit is pocket sized with a long battery life from a PP3 battery, making it ideal for local fault finding and continuity checking of fibres.
