Photodiode
convert's light into current.
See Also: Diode, Laser Diode, Zener Diode, Diode Test, Photodiode Arrays
-
Product
Photodiode
-
A high sensitivity receiver in a fiber pigtail coupled package, it includes a high speed InGaAs avalanche photodiode with a high gain TIA in a hermetically sealed coaxial package. It incorporates an LC/UPC pigtail and a flexible printed circuit (FPC). The signal GND and a receptacle are electrically isolated in this APD receiver.
-
Product
*Photodiode Energy Sensors
-
Ophir photodiode laser energy sensors are able to measure low energy pulses down to 10pJ at frequencies up to 20 kHz. Silicon photodiodes for the UV and visible spectrum and Germanium photodiodes for infrared.
-
Product
16-element Si photodiode array
S12362-321
-
The S12362/S12363 series is a back-illuminated type 16-element photodiode array specifi cally designed for non-destructive X-ray inspection. These are modified versions of our previous products (S11212 series: 1.575 mm pitch). The pitch has been changed to 2.5 mm. The back-illuminated photodiode array is also simple to handle and easily couples to scintillators without having to worry about wire damage because there are no bonding wires and photosensitive areas on the back side.
-
Product
Photodiode Energy Sensors
-
Our photodiode laser energy sensors are able to measure low energy pulses down to 10 pJ at frequencies up to 20 kHz. Silicon photodiodes for the UV and visible spectrum and Germanium photodiodes for infrared.
-
Product
PIN Photodiode
-
PIN photodiode is a kind of photo detector, it can convert optical signals into electrical signals.This technology was invented in the latest of 1950's. There are three regions in this type of diode. There is a p-region an intrinsic region and an n-region. The p-region and n-region are comparatively heavily doped than the p-region and n-region of usual p-n diodes. The width of the intrinsic region should be larger than the space charge width of a normal p-n junction. The PIN photo diode operates with an applied reverse bias voltage and when the reverse bias is applied, the space charge region must cover the intrinsic region completely. Electron hole pairs are generated in the space charge region by photon absorption. The switching speed of frequency response of photo diode is inversely proportional to the life time. The switching speed can be enhanced by a small minority carrier lifetime. For the photo detector applications where the speed of response is important, the depletion region width should be made as large as possible for small minority carrier lifetime as a result the switch speed also increases.
-
Product
Optical Sensors
-
Analog Devices optical sensors are optical sensing front ends that include integrated ultra-low noise amplification and high performance photodiodes. These solutions are used to achieve the highest performance for instrumentation, industrial, or clinical applications; or to optimize a solution to achieve the lowest power dissipation at a given performance level for battery powered and portable applications.
-
Product
UV-Vis & UV-Vis-NIR Systems
-
Our range of powerful and productive UV-Vis and UV-Vis-NIR molecular spectroscopy systems offers options for any optical application. The Cary 60 Spectrophotometer has a unique Xenon flash lamp to enable remote sampling, while the Cary 4000 allows you to measure highly turbid solutions without an integrating sphere. The Cary 8454 photodiode array captures the complete UV-Vis spectrum (190-1100nm) in less than one second.
-
Product
Avalanche Photodiodes
-
Excelitas offers Avalanche Photodiodes (APDs) on both Silicon (Si) and InGaAs materials. Si APDs cover the spectral range of 400 nm to 1100 nm and the InGaAs APDs cover 950 nm to 1550 nm. An Avalanche Photodiode (APD) provides higher sensitivity than a standard photodiode and is for extreme low-level light (LLL) detection and photon counting.
-
Product
UV Index Measurement
-
The sglux UV-Index sensors measure the UVI with a worldwide unique low measurement uncertainty of less than 5 %. This makes our sensors compliant to the highest measurement precisions class one according the DIN/EN 5031-11, chapter 8. Since 2018 our product UV-Cosine_UVI (ERYCA) is appointed for public authority tasks: The German Federal Office for Radiation Protection (BfS) services 27 measurement points in Germany for public information of the daily UV-Index. Twenty of these points (Andernach, Chieming, Duderstadt, Fichtelberg, Genthin, Giessen-Wettenberg, Schauenburg-Kassel, Langen, Lueneburg, Munchen-Neuherberg, Norderney, Belm/Osnabrueck, Schauinsland, Tholey, Todendorf, Waldhof-Falkenstein, Waldmuenchen, Wurmberg, Zingst and Zirchow) use the sglux ERYCA to obtain the local UV-Index value. In 2017 ARPANSA (Australian Government’s primary authority on radiation protection and nuclear safety) began replacing the existing biometers with SiC photodiode UV sensors (sglux ERYCA) at all network sites. There are currently thirteen measurement sites in Australia that have been upgraded to the new sensors.
-
Product
Handheld Laser Power & Energy Meter
Nova ΙΙ 7Z01550
-
*Compatible with all standard Ophir Thermopile, BeamTrack, Pyroelectric and Photodiode sensors.*Large, high definition LCD display.*Both digital and analog needle display.*USB and RS232 output to PC with Statistics package.*Select between English and Japanese interfaces*Analog output.*Soft keys and menu driven functions with on line help.*Log every data point at up to 4000Hz with pyroelectric sensors.*Non-volatile data storage up to 59,400 points.*Laser tuning screen and power log.*2 position kickstand.*System Integrator Tools included: LabVIEW VIs, COM Object Interface.
-
Product
Optical Transimpedance Amplifiers
-
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
Product
Laser Power / Energy Meter
StarBright 7Z01580
-
*Compatible with all standard Ophir thermal, BeamTrack, pyroelectric (PE-C series) and photodiode sensors*Brilliant color large size TFT 320x240 display*Choose between Digital with Bargraph, Analog Needle, Line Plot (for laser tuning), Pulse Chart, Pass/Fail, *Position, Stability, Real Time Statistics displays*Sophisticated power and energy logging, including logging every point at up to 5000Hz with Pyro sensors*Math functions for advanced processing such as Density, Scale Factor, Normalize against base line, etc.*Can mix functions together and display the results graphically. Function results can also be logged.*USB Disk on Key (Thumb Drive) for nearly unlimited data storage.*USB and RS232 interfaces with StarLab PC applications and User Commands document
-
Product
Low Input Bias Current Op Amps (≤100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
FTTx Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.
-
Product
Two -Dimensional PSD
-
Functions according to the Lateral Effect Photodiode principle. It is an analogue device and therefore displays excellent position resolution. The resolution is determined by the system signal-to-noise ratio. It is operated in the biased mode. Typical applications include: distance andheight measurement, alignment, position and motion measurements and vibration studies
-
Product
10G APD Photoreceivers
-
Macom Technology Solutions Holdings Inc.
MACOM offers high-sensitivity avalanche photodiode (APD) based photoreceivers in a variety of packages, including ROSA, OEM module and instrument-style. A wide range of 10G solutions are available with both multimode and single-mode fiber-coupled products.
-
Product
Detectors & Sensors
-
Excelitas offers Photonic Detection Solutions ranging from Silicon and InGaAS PINs and Avalanche Photodiodes, Hybrid Receivers, and Photon Counting Modules to address high-performance, high-volume applications across a wide range of markets. Excelitas Thermal IR Sensors represent a broad range of Pyroelectric Detectors, Thermopile Detectors and IR Sensor Modules used for motion detection, presence monitoring, temperature measurement and gas detection.
-
Product
Current to Digital
-
Analog Devices’ breakthrough current-to-digital converter technology is backed by award winning expertise to help solve your medical, industrial, and security application needs. Our high speed, high resolution ADC modules enable improved CT scanner data acquisition, photodiode sensors and power monitoring, spectroscopy, and high channel count data acquisition systems.
-
Product
X-Ray And Gamma Detector Systems
-
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
Product
Avalanche Photodiodes
-
These avalanche photodiodes (APDs) are silicon photodiodes with an internal gain mechanism. As with a conventional photodiode, absorption of incident photons creates electron-hole pairs. A high reverse bias voltage creates a strong internal electric field, which accelerates the electrons through the silicon crystal lattice and produces secondary electrons by impact ionization. The resulting electron avalanche can produce gain factors up to several hundred.
-
Product
2x8 Coherent Mixer With Single-ended Photodetectors
-
This page defines the requirement of a special coherent receiver with 8 single-ended photodiode outputs, per customer request. The coherent mixer, consisting of two polarization-diversified 90deg optical hybrids, a polarizing beam splitter and a beam splitter, is exactly same as existing DP-QPSK coherent mixer, and therefore offering same optical performance.
-
Product
Benchtop Femtosecond/Picosecond Lasers and Amplifiers
-
The systems feature a portable design with user-friendly front panel control knobs for adjustment of output parameters, such as power, pulse width and repetition rate. With wavelength options of 780 nm, 850 nm, 1310 nm, and 1550 nm, pulse widths as low as < 0.3 ps, and GHz low-jitter synchronization signals, these systems provide ideal optical sources for high speed transceiver conformance testing and photodiode characterization.
-
Product
Gated Integrator | Boxcar Averager
GIA100
-
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
Product
OLED Life Time Test System
-
A system for measuring measurement items (brightness and so forth through Voltage, Current, and Photodiode) and their lifetime in intervals of set time, while supplying power to multiple (32 Channel) OLED panel stably.
-
Product
Spectral Response (Spectral Sensitivity) Measurement
-
It is used to measure the spectral response (spectral sensitivity) of photoelectric conversion devices (photodetectors / sensors) such as silicon photodiodes and CCD · CMOS image sensors . Measurement in the broadband wavelength region can be performed with low stray light.
-
Product
High Speed Free Space Optical Detectors
-
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
Product
Photodiodes
-
Opto Diode manufactures high quality standard and custom photodiodes. Our wide range of standard device feature low dark current and low capacitance. The silicon detectors are ideal for general purpose applications, laser monitoring, position sensing, measuring photons, electrons, or X-rays, or for detecting sun and rain applications. The devices operate from the deep UV to the near-infrared wavelengths.
-
Product
2D CMOS Image Sensor
Lince6M5
-
Lince6M5 is a single chip, fully digital, high speed CMOS active pixel sensor which is designed for maximum flexibility. It has excellent performance in a large variety of applications, ranging from low noise, high dynamic range surveillance, to high speed slow motion analysis, including high resolution machine vision applications. Lince6M5 incorporates a high speed 6.5MP CMOS active pixel image sensor providing both global and rolling electronic shutter, as well as High Dynamic Range (HDR) features. The sensor array utilizes active CMOS pixels with pinned photodiodes to deliver high image quality whilst maintaining the size, cost, and integration advantage of the CMOS technology.
-
Product
Power Meter
TW3211
-
Techwin(China) Industry Co., Ltd
TW3211 optical power meter Is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optical fibers. A Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, a wide range of power measurement, high accuracy, an user self-calibration function and a reference power level storage.
-
Product
High End Portable Laser Power/Energy Meter
Centauri Single Channel P/N7Z01700
-
*Compatible with all standard Ophir Thermal, BeamTrack, Pyroelectric and Photodiode sensors*Large 7" Full Color Touch Display*Multilingual interface – English, French, Spanish, Italian, German, Russian, Japanese, Chinese and Korean*Single and Dual Channel models available*Various Displays: Bargraph, Analog Needle, Line Plot, Pulse Chart, Pass/Fail, Position, Stability, and Real Time Statistics*Dual Channel Instrument supports Split and Merged Graphical Displays*Sophisticated power and energy logging, including logging every pulse at up to 25000Hz with Pyro sensors*Math functions: Density, Scale Factor, Normalize against base line, etc. Functions can be mixed together, displayed graphically, and can also be logged
